Hi Bjorn, On 4/5/21 6:18 PM, Bjorn Andersson wrote:
On Thu 25 Feb 12:27 CST 2021, Thara Gopinath wrote:Add register programming sequence for enabling AEAD algorithms on the Qualcomm crypto engine. Signed-off-by: Thara Gopinath <thara.gopinath@xxxxxxxxxx> --- drivers/crypto/qce/common.c | 155 +++++++++++++++++++++++++++++++++++- 1 file changed, 153 insertions(+), 2 deletions(-) diff --git a/drivers/crypto/qce/common.c b/drivers/crypto/qce/common.c index 05a71c5ecf61..54d209cb0525 100644 --- a/drivers/crypto/qce/common.c +++ b/drivers/crypto/qce/common.c @@ -15,6 +15,16 @@ #include "core.h" #include "regs-v5.h" #include "sha.h" +#include "aead.h" + +static const u32 std_iv_sha1[SHA256_DIGEST_SIZE / sizeof(u32)] = { + SHA1_H0, SHA1_H1, SHA1_H2, SHA1_H3, SHA1_H4, 0, 0, 0 +}; + +static const u32 std_iv_sha256[SHA256_DIGEST_SIZE / sizeof(u32)] = { + SHA256_H0, SHA256_H1, SHA256_H2, SHA256_H3, + SHA256_H4, SHA256_H5, SHA256_H6, SHA256_H7 +};static inline u32 qce_read(struct qce_device *qce, u32 offset){ @@ -96,7 +106,7 @@ static inline void qce_crypto_go(struct qce_device *qce, bool result_dump) qce_write(qce, REG_GOPROC, BIT(GO_SHIFT)); }-#ifdef CONFIG_CRYPTO_DEV_QCE_SHA+#if defined(CONFIG_CRYPTO_DEV_QCE_SHA) || defined(CONFIG_CRYPTO_DEV_QCE_AEAD) static u32 qce_auth_cfg(unsigned long flags, u32 key_size, u32 auth_size) { u32 cfg = 0; @@ -139,7 +149,9 @@ static u32 qce_auth_cfg(unsigned long flags, u32 key_size, u32 auth_size)return cfg;} +#endif+#ifdef CONFIG_CRYPTO_DEV_QCE_SHAstatic int qce_setup_regs_ahash(struct crypto_async_request *async_req) { struct ahash_request *req = ahash_request_cast(async_req); @@ -225,7 +237,7 @@ static int qce_setup_regs_ahash(struct crypto_async_request *async_req) } #endif-#ifdef CONFIG_CRYPTO_DEV_QCE_SKCIPHER+#if defined(CONFIG_CRYPTO_DEV_QCE_SKCIPHER) || defined(CONFIG_CRYPTO_DEV_QCE_AEAD) static u32 qce_encr_cfg(unsigned long flags, u32 aes_key_size) { u32 cfg = 0; @@ -271,7 +283,9 @@ static u32 qce_encr_cfg(unsigned long flags, u32 aes_key_size)return cfg;} +#endif+#ifdef CONFIG_CRYPTO_DEV_QCE_SKCIPHERstatic void qce_xts_swapiv(__be32 *dst, const u8 *src, unsigned int ivsize) { u8 swap[QCE_AES_IV_LENGTH]; @@ -386,6 +400,139 @@ static int qce_setup_regs_skcipher(struct crypto_async_request *async_req) } #endif+#ifdef CONFIG_CRYPTO_DEV_QCE_AEAD+static int qce_setup_regs_aead(struct crypto_async_request *async_req) +{ + struct aead_request *req = aead_request_cast(async_req); + struct qce_aead_reqctx *rctx = aead_request_ctx(req); + struct qce_aead_ctx *ctx = crypto_tfm_ctx(async_req->tfm); + struct qce_alg_template *tmpl = to_aead_tmpl(crypto_aead_reqtfm(req)); + struct qce_device *qce = tmpl->qce; + __be32 enckey[QCE_MAX_CIPHER_KEY_SIZE / sizeof(__be32)] = {0}; + __be32 enciv[QCE_MAX_IV_SIZE / sizeof(__be32)] = {0}; + __be32 authkey[QCE_SHA_HMAC_KEY_SIZE / sizeof(__be32)] = {0}; + __be32 authiv[SHA256_DIGEST_SIZE / sizeof(__be32)] = {0}; + __be32 authnonce[QCE_MAX_NONCE / sizeof(__be32)] = {0}; + unsigned int enc_keylen = ctx->enc_keylen; + unsigned int auth_keylen = ctx->auth_keylen; + unsigned int enc_ivsize = rctx->ivsize; + unsigned int auth_ivsize; + unsigned int enckey_words, enciv_words; + unsigned int authkey_words, authiv_words, authnonce_words; + unsigned long flags = rctx->flags; + u32 encr_cfg = 0, auth_cfg = 0, config, totallen;I don't see any reason to initialize encr_cfg or auth_cfg.
right.. I will remove it
+ u32 *iv_last_word; + + qce_setup_config(qce); + + /* Write encryption key */ + qce_cpu_to_be32p_array(enckey, ctx->enc_key, enc_keylen); + enckey_words = enc_keylen / sizeof(u32); + qce_write_array(qce, REG_ENCR_KEY0, (u32 *)enckey, enckey_words);Afaict all "array registers" in this function are affected by the CRYPTO_SETUP little endian bit, but you set this bit before launching the operation dependent on IS_CCM(). So is this really working for the !IS_CCM() case?
I am not sure I understand you. Below , /* get little endianness */ config = qce_config_reg(qce, 1); qce_write(qce, REG_CONFIG, config); is outside of any checks..
+ + /* Write encryption iv */ + qce_cpu_to_be32p_array(enciv, rctx->iv, enc_ivsize); + enciv_words = enc_ivsize / sizeof(u32); + qce_write_array(qce, REG_CNTR0_IV0, (u32 *)enciv, enciv_words);It would be nice if this snippet was extracted to a helper function.+ + if (IS_CCM(rctx->flags)) { + iv_last_word = (u32 *)&enciv[enciv_words - 1]; +// qce_write(qce, REG_CNTR3_IV3, enciv[enciv_words - 1] + 1);I believe this is a remnant of the two surrounding lines.
It indeed is.. I will remove it.
+ qce_write(qce, REG_CNTR3_IV3, (*iv_last_word) + 1);enciv is an array of big endian 32-bit integers, which you tell the compiler to treat as cpu-native endian, and then you do math on it. Afaict from the documentation the value of REG_CNTR3_IVn should be set to rctx->iv + 1, but if the hardware expects these in big endian then I think you added 16777216.
So, the crypto engine documentation talks of writing to these registers in little endian mode. The byte stream that you get for iv from the user is in big endian mode as in the MSB is byte 0. So we kind of invert this and write to these registers. This is what happens with declaring the __be32 array and copying words to it from the byte stream. So now byte 0 is the LSB and a +1 will just add a 1 to it.
I suspect from what I read in the documentation we could get away by removing this and writing the big endian byte stream directly and never setting the little endian in config register. Though I am not sure if this has ever been tested out. If we change it, it will be across algorithms and as a separate effort.
Perhaps I'm missing something here though? PS. Based on how the documentation is written, shouldn't you write out REG_CNTR_IV[012] as well?
It is done on top, right ? qce_write_array(qce, REG_CNTR0_IV0, (u32 *)enciv, enciv_words);
+ qce_write_array(qce, REG_ENCR_CCM_INT_CNTR0, (u32 *)enciv, enciv_words); + qce_write(qce, REG_CNTR_MASK, ~0); + qce_write(qce, REG_CNTR_MASK0, ~0); + qce_write(qce, REG_CNTR_MASK1, ~0); + qce_write(qce, REG_CNTR_MASK2, ~0); + } + + /* Clear authentication IV and KEY registers of previous values */ + qce_clear_array(qce, REG_AUTH_IV0, 16); + qce_clear_array(qce, REG_AUTH_KEY0, 16); + + /* Clear byte count */ + qce_clear_array(qce, REG_AUTH_BYTECNT0, 4); + + /* Write authentication key */ + qce_cpu_to_be32p_array(authkey, ctx->auth_key, auth_keylen); + authkey_words = DIV_ROUND_UP(auth_keylen, sizeof(u32)); + qce_write_array(qce, REG_AUTH_KEY0, (u32 *)authkey, authkey_words); + + if (IS_SHA_HMAC(rctx->flags)) { + /* Write default authentication iv */ + if (IS_SHA1_HMAC(rctx->flags)) { + auth_ivsize = SHA1_DIGEST_SIZE; + memcpy(authiv, std_iv_sha1, auth_ivsize); + } else if (IS_SHA256_HMAC(rctx->flags)) { + auth_ivsize = SHA256_DIGEST_SIZE; + memcpy(authiv, std_iv_sha256, auth_ivsize); + } + authiv_words = auth_ivsize / sizeof(u32); + qce_write_array(qce, REG_AUTH_IV0, (u32 *)authiv, authiv_words);AUTH_IV0 is affected by the little endian configuration, does this imply that IS_SHA_HMAC() and IS_CCM() are exclusive bits of rctx->flags? If so I think it would be nice if you grouped the conditionals in a way that made that obvious when reading the function.
So yes IS_SHA_HMAC() and IS_CCM() are exclusive bits of rctx->flags. AUTH_IVn is 0 for ccm and has initial value for HMAC algorithms. I don't understand the confusion here.
+ } + + if (IS_CCM(rctx->flags)) { + qce_cpu_to_be32p_array(authnonce, rctx->ccm_nonce, QCE_MAX_NONCE); + authnonce_words = QCE_MAX_NONCE / sizeof(u32); + qce_write_array(qce, REG_AUTH_INFO_NONCE0, (u32 *)authnonce, authnonce_words); + } + + /* Set up ENCR_SEG_CFG */ + encr_cfg = qce_encr_cfg(flags, enc_keylen); + if (IS_ENCRYPT(flags)) + encr_cfg |= BIT(ENCODE_SHIFT); + qce_write(qce, REG_ENCR_SEG_CFG, encr_cfg); + + /* Set up AUTH_SEG_CFG */ + auth_cfg = qce_auth_cfg(rctx->flags, auth_keylen, ctx->authsize); + auth_cfg |= BIT(AUTH_LAST_SHIFT); + auth_cfg |= BIT(AUTH_FIRST_SHIFT); + if (IS_ENCRYPT(flags)) { + if (IS_CCM(rctx->flags)) + auth_cfg |= AUTH_POS_BEFORE << AUTH_POS_SHIFT; + else + auth_cfg |= AUTH_POS_AFTER << AUTH_POS_SHIFT; + } else { + if (IS_CCM(rctx->flags)) + auth_cfg |= AUTH_POS_AFTER << AUTH_POS_SHIFT; + else + auth_cfg |= AUTH_POS_BEFORE << AUTH_POS_SHIFT; + } + qce_write(qce, REG_AUTH_SEG_CFG, auth_cfg); + + totallen = rctx->cryptlen + rctx->assoclen; + + /* Set the encryption size and start offset */ + if (IS_CCM(rctx->flags) && IS_DECRYPT(rctx->flags)) + qce_write(qce, REG_ENCR_SEG_SIZE, rctx->cryptlen + ctx->authsize); + else + qce_write(qce, REG_ENCR_SEG_SIZE, rctx->cryptlen); + qce_write(qce, REG_ENCR_SEG_START, rctx->assoclen & 0xffff); + + /* Set the authentication size and start offset */ + qce_write(qce, REG_AUTH_SEG_SIZE, totallen); + qce_write(qce, REG_AUTH_SEG_START, 0); + + /* Write total length */ + if (IS_CCM(rctx->flags) && IS_DECRYPT(rctx->flags)) + qce_write(qce, REG_SEG_SIZE, totallen + ctx->authsize); + else + qce_write(qce, REG_SEG_SIZE, totallen); + + /* get little endianness */ + config = qce_config_reg(qce, 1); + qce_write(qce, REG_CONFIG, config); + + /* Start the process */ + if (IS_CCM(flags)) + qce_crypto_go(qce, 0);Second parameter is defined as "bool", please use "false" here (and true below). Or qce_crypto_go(qce, !IS_CCM(flags));
will do... I like the one liner better. -- Warm Regards Thara
