On Fri, Feb 22, 2019 at 11:14 AM David Summers <beagleboard@xxxxxxxxxxxxxxxxxxx> wrote: > > Hi Vasily, > > Just catching up with this series - good that you are doing it. We need > it for users on ArchLinux ARM! > > On question though, what is "firmware-postfix" used for? I see in the > documentation, that it points to the board name. But can't see where > else it is used. See h5_serdev_probe() in drivers/bluetooth/hci_h5.c. Basically it specifies what firmware config to use. I agree with Rob that we should probably use firmware-name here instead. > Is there a need to have the board name? As far as I understand firmware config depends on board, so I think it's a good idea to use board name here. > Anyway good work. Thanks! > > David. > > On 18/02/2019 22:28, Vasily Khoruzhick wrote: > > On Mon, Feb 18, 2019 at 2:08 PM Stefan Wahren <stefan.wahren@xxxxxxxx> wrote: > >> Hi Vasily, > > Hi Stefan, > > > >>> Vasily Khoruzhick <anarsoul@xxxxxxxxx> hat am 18. Februar 2019 um 22:24 geschrieben: > >>> > >>> > >>> On Mon, Feb 18, 2019 at 1:10 PM Rob Herring <robh@xxxxxxxxxx> wrote: > >>>> On Fri, Jan 18, 2019 at 09:02:27AM -0800, Vasily Khoruzhick wrote: > >>>>> Add binding document for bluetooth part of RTL8723BS/RTL8723CS > >>>>> > >>>>> Signed-off-by: Vasily Khoruzhick <anarsoul@xxxxxxxxx> > >>>>> --- > >>>>> .../bindings/net/rtl8723bs-bluetooth.txt | 35 +++++++++++++++++++ > >>>>> 1 file changed, 35 insertions(+) > >>>>> create mode 100644 Documentation/devicetree/bindings/net/rtl8723bs-bluetooth.txt > >>>>> > >>>>> diff --git a/Documentation/devicetree/bindings/net/rtl8723bs-bluetooth.txt b/Documentation/devicetree/bindings/net/rtl8723bs-bluetooth.txt > >>>>> new file mode 100644 > >>>>> index 000000000000..8357f242ae4c > >>>>> --- /dev/null > >>>>> +++ b/Documentation/devicetree/bindings/net/rtl8723bs-bluetooth.txt > >>>>> @@ -0,0 +1,35 @@ > >>>>> +RTL8723BS/RTL8723CS Bluetooth > >>>>> +--------------------- > >>>>> + > >>>>> +RTL8723CS/RTL8723CS is WiFi + BT chip. WiFi part is connected over SDIO, while > >>>>> +BT is connected over serial. It speaks H5 protocol with few extra commands > >>>>> +to upload firmware and change module speed. > >>>>> + > >>>>> +Required properties: > >>>>> + > >>>>> + - compatible: should be one of the following: > >>>>> + * "realtek,rtl8723bs-bt" > >>>>> + * "realtek,rtl8723cs-bt" > >>>>> +Optional properties: > >>>>> + > >>>>> + - device-wake-gpios: GPIO specifier, used to wakeup the BT module (active high) > >>>>> + - enable-gpios: GPIO specifier, used to enable the BT module (active high) > >>>>> + - host-wake-gpios: GPIO specifier, used to wakeup the host processor (active high) > >>>>> + - firmware-postfix: firmware postfix to be used for firmware config > >> sorry, i didn't noticed your great series before. David and i working at the same stuff but for the Asus Tinker Board. > >> > >> I created a similiar yet untested patch version for hci_h5 [1]. Maybe it's useful. > > Looks good to me, but you may need to add firmware-postfix. > > > >> Just a comment about the binding. It's really necessary to add the reset-gpio? Can't we use the enable-gpio with inverse polarity for this? > > Yes, we can use enable-gpio instead of reset-gpio on pine64 and pinebook. > > > >> Stefan > >
