Re: [PATCH] Bluetooth: qca: generalise device address check

[Date Prev][Date Next][Thread Prev][Thread Next][Date Index][Thread Index]

 



Hi Luiz,

On 5/2/2024 11:02 PM, Luiz Augusto von Dentz wrote:
Hi Janaki,

On Thu, May 2, 2024 at 1:03 PM Janaki Ramaiah Thota
<quic_janathot@xxxxxxxxxxx> wrote:

Hi Johan,

On 5/2/2024 3:41 PM, Johan Hovold wrote:
On Thu, May 02, 2024 at 12:35:19PM +0530, Janaki Ramaiah Thota wrote:
On 4/30/2024 6:37 PM, Johan Hovold wrote:

But here we disagree. A non-unique address is not a valid one as it will
cause collisions if you have more than one such controller.

I understand that this may be convenient/good enough for developers in
some cases, but this can hurt end users that do not realise why things
break.

And a developer can always configure an address manually or patch the
driver as needed for internal use.

Are there any other reasons that makes you want to keep the option to
configure the device address through NVM files? I'm assuming you're not
relying on patching NVM files to provision device-specific addresses
after installation on target?

We prefer unique address to be flashed on OTP (persistent) memory of
BT-Chip, which is supported by almost all QC BT-chips.

Yes, that is certainly the best option for everyone.

If someone is not able to do that/ does not prefer that, they still
have an option to flash unique address in firmware binary (NVM)file.
This does not require setting BD address from user space.

Also until a developer flashes OTP/ keep unique BD-Address in NVM,
he should be able to run most of the use cases from Device, that's
why we want to make it as configured.

Ok, but a developer can still do this since they can patch the driver to
disable the check temporarily or, alternatively, just update the
devicetree with a valid unique address.

In our opinion this provides best Out of box experience.


If a developer has to patch a code/update device-tree, that is not
a "out of box" experience. By "out of box" we meant, things should
work without much changes required.

You can also look into improving support in user space (e.g. bluez) for
providing a valid unique address in a simple text-based configuration
file.


We don't think putting a must-have dependency in user space is the
right thing to do, especially when we own a code in kernel space.

That would be useful for all Linux users and not require having access
to Qualcomm specific tools to update the NVM configuration file (which
could also be in a read-only file system, e.g. on Android).


Having a non-unique valid address allows a developer to handle all
scenarios where he/she is dealing with DUT + commercial device and
in such case, default BD-Address from nvm file should also be okay.
Only when 2/more similar devices are in the mix, they need unique
address. In that case we are providing end developers with a NVM
utility(part of Qcom build Not open source tool)to change this
default BD-Address.

And we don't agree with doing that, that is why the controller shall
be marked as unconfigured when a non-unique address is used and if you
insist in doing that I will probably have to escalate that you guys
are intentionally using addresses that can clash over the air.

If the firmware is intended for developer, it shall be kept private,
public firmware shall never use duplicate addresses, ever, and don't
come back with arguments like that only when 2/more similar devices
are in the mix but that would just stress even more the point that you
are breaking stuff _on purpose_, which is pretty bad by itself, and
then suggesting to use a non-open-source tool to fix the address is
making things worse because end users can be affected by this, that
really fills like you don't care if your hardware works on regular
Linux distros and in that case I will probably move it to
driver/staging.


Our intention is not to break things, instead we wanted driver should
be sufficient to set a BD-Address, without putting a necessary
requirement on user space/Stack to configure BD-Address.
Other solutions ( like Android ) were approaching this
problem in this way. Now we also agree with your point
that we should not leave any scope for having a non-unique
BD-Address. Current bottleneck that we see with driver creating
and managing unique BD-Address on its own is how to ensure
persistence on reboot. If you are aware of any mechanism with
which we can ensure persistence in kernel across reboot please
let us know, otherwise we will write/reuse bluez-mgmt user
space utility to solve this problem.

Johan

-Janaki Ram


--
Luiz Augusto von Dentz

-Janaki Ram




[Index of Archives]     [Bluez Devel]     [Linux Wireless Networking]     [Linux Wireless Personal Area Networking]     [Linux ATH6KL]     [Linux USB Devel]     [Linux Media Drivers]     [Linux Audio Users]     [Linux Kernel]     [Linux SCSI]     [Big List of Linux Books]

  Powered by Linux