This helper doesn't buy us much over calling kmap_atomic directly.
In fact in the only caller it does a bit of useless work as the
caller already has the bvec at hand, and said caller would even
buggy for a multi-segment bio due to the use of this helper.
So just remove it.
Signed-off-by: Christoph Hellwig <hch@xxxxxx>
---
Jens, this is on top of your bio_kmap_irq removal patch on the list.
Documentation/block/biodoc.txt | 11 +++++------
arch/xtensa/platforms/iss/simdisk.c | 4 ++--
block/blk-settings.c | 2 +-
include/linux/bio.h | 12 ------------
4 files changed, 8 insertions(+), 21 deletions(-)
diff --git a/Documentation/block/biodoc.txt b/Documentation/block/biodoc.txt
index 01c0a03407cc..86927029a52d 100644
--- a/Documentation/block/biodoc.txt
+++ b/Documentation/block/biodoc.txt
@@ -216,10 +216,9 @@ may need to abort DMA operations and revert to PIO for the transfer, in
which case a virtual mapping of the page is required. For SCSI it is also
done in some scenarios where the low level driver cannot be trusted to
handle a single sg entry correctly. The driver is expected to perform the
-kmaps as needed on such occasions using the bio_kmap_irq and friends
-routines as appropriate. A driver could also use the blk_queue_bounce()
-routine on its own to bounce highmem i/o to low memory for specific requests
-if so desired.
+kmaps as needed on such occasions as appropriate. A driver could also use
+the blk_queue_bounce() routine on its own to bounce highmem i/o to low
+memory for specific requests if so desired.
iii. The i/o scheduler algorithm itself can be replaced/set as appropriate
@@ -1137,8 +1136,8 @@ use dma_map_sg for scatter gather) to be able to ship it to the driver. For
PIO drivers (or drivers that need to revert to PIO transfer once in a
while (IDE for example)), where the CPU is doing the actual data
transfer a virtual mapping is needed. If the driver supports highmem I/O,
-(Sec 1.1, (ii) ) it needs to use __bio_kmap_atomic or similar to
-temporarily map a bio into the virtual address space.
+(Sec 1.1, (ii) ) it needs to use kmap_atomic or similar to temporarily map
+a bio into the virtual address space.
8. Prior/Related/Impacted patches
diff --git a/arch/xtensa/platforms/iss/simdisk.c b/arch/xtensa/platforms/iss/simdisk.c
index c45b90bb9339..eacf1e433518 100644
--- a/arch/xtensa/platforms/iss/simdisk.c
+++ b/arch/xtensa/platforms/iss/simdisk.c
@@ -110,13 +110,13 @@ static blk_qc_t simdisk_make_request(struct request_queue *q, struct bio *bio)
sector_t sector = bio->bi_iter.bi_sector;
bio_for_each_segment(bvec, bio, iter) {
- char *buffer = __bio_kmap_atomic(bio, iter);
+ char *buffer = kmap_atomic(bvec.bv_page) + bvec.bv_offset;
unsigned len = bvec.bv_len >> SECTOR_SHIFT;
simdisk_transfer(dev, sector, len, buffer,
bio_data_dir(bio) == WRITE);
sector += len;
- __bio_kunmap_atomic(buffer);
+ kunmap_atomic(buffer)
}
bio_endio(bio);
diff --git a/block/blk-settings.c b/block/blk-settings.c
index 8559e9563c52..48ebe6be07b7 100644
--- a/block/blk-settings.c
+++ b/block/blk-settings.c
@@ -157,7 +157,7 @@ EXPORT_SYMBOL(blk_set_stacking_limits);
* Caveat:
* The driver that does this *must* be able to deal appropriately
* with buffers in "highmemory". This can be accomplished by either calling
- * __bio_kmap_atomic() to get a temporary kernel mapping, or by calling
+ * kmap_atomic() to get a temporary kernel mapping, or by calling
* blk_queue_bounce() to create a buffer in normal memory.
**/
void blk_queue_make_request(struct request_queue *q, make_request_fn *mfn)
diff --git a/include/linux/bio.h b/include/linux/bio.h
index fd3e11284a38..65f613612fb0 100644
--- a/include/linux/bio.h
+++ b/include/linux/bio.h
@@ -128,18 +128,6 @@ static inline void *bio_data(struct bio *bio)
*/
#define bvec_to_phys(bv) (page_to_phys((bv)->bv_page) + (unsigned long) (bv)->bv_offset)
-/*
- * queues that have highmem support enabled may still need to revert to
- * PIO transfers occasionally and thus map high pages temporarily. For
- * permanent PIO fall back, user is probably better off disabling highmem
- * I/O completely on that queue (see ide-dma for example)
- */
-#define __bio_kmap_atomic(bio, iter) \
- (kmap_atomic(bio_iter_iovec((bio), (iter)).bv_page) + \
- bio_iter_iovec((bio), (iter)).bv_offset)
-
-#define __bio_kunmap_atomic(addr) kunmap_atomic(addr)
-
/*
* merge helpers etc
*/
--
2.14.2
