On 6/20/06, Stephen Cameron <smcameron@xxxxxxxxx> wrote:
Mark Knecht wrote;
> On 6/20/06, Stephen Cameron <smcameron@xxxxxxxxx> wrote:
> <SNIP>
> >
> > Well, here's what I've tried so far tonight:
> >
> > Ran jack as root.
> > Ran qjackctl as root.
>
> Let's try running Jack from within QJC. That way you can set up a Jack
> profile with settings that make sense and then you can save them.
Actually I did. After I typed "Run jack as root", I meant to
replace that line with "Run qjackctl as root", not keep both
lines.
>
> I suspect, for no good reason, that the mixer and the Hammerfall
> wouldn't be happy if the Hammerfall is really running at 22K.
Ok. I don't know what to make of that.
>
> In QJC make sure that you are choosing the right soundcard. Is it
> possible that you have a built in sound card that is set up for card 0
> and the Hammerfall is actually card 1?
>
I set in the Setup window of qjackctl -> interface: "hw:1"
but actually, this is a good point, I actually
have _three_ soundcards, I think. The first is
the completely useless one on the motherboard,
the 2nd is an "audigy2 value" and the third is
the RME. So, now that you mention it, I would
think it should be hw:2, but somehow I still
think it's "hw:1" Maybe it's because the motherboard
soundcard is so utterly useless it doesn't even
show up for work? Er, come to think of it I may have
disabled it in the ROM setup of my computer because
it was only causing problems... I can't recall if I
did that or not. I am sure I thought about trying to do
it. In any case, I think "hw:1" is correct, because of this:
[scameron@zuul ~]$ arecord -l
**** List of CAPTURE Hardware Devices ****
card 0: Audigy2 [Audigy 2 Value [SB0400]], device 0: emu10k1 [ADC Capture/Standard PCM Playback]
Subdevices: 1/1
Subdevice #0: subdevice #0
card 0: Audigy2 [Audigy 2 Value [SB0400]], device 1: emu10k1 mic [Mic Capture]
Subdevices: 1/1
Subdevice #0: subdevice #0
card 0: Audigy2 [Audigy 2 Value [SB0400]], device 2: emu10k1 efx [Multichannel Capture/PT
Playback]
Subdevices: 1/1
Subdevice #0: subdevice #0
card 1: R15 [RME Digi9636 (Rev 1.5)], device 0: RME Digi9636 (Rev 1.5) [RME Digi9636 (Rev 1.5)]
Subdevices: 1/1
Subdevice #0: subdevice #0
[scameron@zuul ~]$
[scameron@zuul ~]$ cat /proc/asound/cards
0 [Audigy2 ]: Audigy2 - Audigy 2 Value [SB0400]
Audigy 2 Value [SB0400] (rev.0, serial:0x10011102) at 0x9000, irq 11
1 [R15 ]: RME9636 - RME Digi9636 (Rev 1.5)
RME Digi9636 (Rev 1.5) at 0xea000000, irq 10
[scameron@zuul ~]$
>
> mark@lightning ~ $ cat /proc/asound/cards
> 0 [CK804 ]: NFORCE - NVidia CK804
> NVidia CK804 with ALC850 at 0xda103000, irq 225
> 1 [DSP ]: H-DSP - Hammerfall DSP
> RME Hammerfall HDSP 9652 at 0xda000000, irq 66
> mark@lightning ~ $
>
>
> If yours looks anything like this then the default Jack setting is
> running Jack with the built in card. However since you see 18 IO's it
> sounds like the Hammerfall and not a built in unless they are virtual
> ports...
Yeah, I set it to "hw:1" so I think it's correct.
>
> >From within QJC I start Jack here with the command shown, and again
> this is my HDSP9652, not a Hammerfall, but it should be very close if
> not exactly the same, and this is what I see in QJC's message window:
>
> (you do NOT need to run 64/2 for testing...)
>
> 20:01:52.019 jackd -R -P80 -p512 -dalsa -dhw:1 -r44100 -p64 -n2
Ok, I will have to try that one.
> 20:01:52.035 JACK was started with PID=4148 (0x1034).
> jackd 0.102.14
> Copyright 2001-2005 Paul Davis and others.
> jackd comes with ABSOLUTELY NO WARRANTY
> This is free software, and you are welcome to redistribute it
> under certain conditions; see the file COPYING for details
> JACK compiled with System V SHM support.
> loading driver ..
> apparent rate = 44100
> creating alsa driver ... hw:1|hw:1|64|2|44100|0|0|nomon|swmeter|-|32bit
> control device hw:1
> configuring for 44100Hz, period = 64 frames, buffer = 2 periods
> ALSA: final selected sample format for capture: 32bit little-endian
> ALSA: use 2 periods for capture
> ALSA: final selected sample format for playback: 32bit little-endian
> ALSA: use 2 periods for playback
> 20:01:54.084 Server configuration saved to "/home/mark/.jackdrc".
>
> Hope this helps somehow,
> Mark
>
__________________________________________________
Do You Yahoo!?
Tired of spam? Yahoo! Mail has the best spam protection around
http://mail.yahoo.com
