On Thu, 2004-07-08 at 20:49, Joseph Dell'Orfano wrote: > I missed the beginning of this thread, so forgive me if this has already > been covered. Did you try listening through the onboard mixer at all? > This removes the software from the equation. Use envy24control and route > the first 2 channels through the onboard mixer, then listen for your > crackles/pops/snaps. My delta 1010lt performs flawlessly on linux > (fedora core 1). > > -Joe No I didn't...but thanks for the idea. I think I have a handle on this. And mush thanks to Mr Depner for helping me out with an .asoundrc question. To provide the solution after all my bleating: I had been using the "default" alsa setting in Qjackctl. I had this nagging feeling that setting up an .asoundrc as I have always done in the past would resolve this, or at least help. I read somewhere that the "default" setting is not as efficient? Anyway, no amount of googling would give me enough info for an .asounrc config for the 8 analgue I/O's (or so it seemed to my sublime ignorance). I tried several different configs and each way I entered them thru Qjackctl would not provide success. Finally, I read Jan's how to again and looking at his script and knowing he is also using the 1010, I saw he had the generic .asoundrc from the Alsa site. I e-mailed him asking how and if, in fact, he gets the 8 I/O's showing in the Connect pannel of Qjackctl. He was kind enough to indulge me and said that he is now using the .asoundrc that is listed for a "hoontech" card with the Envy24 chip on the bottom of the Envy24 pages in the Alsa site Details and docs. So I figured I'd plug it in and see... I fired up Qjackctl again and tried the usual "hw:0" and "default" settings. None would connect at first. Then I tried setting the "channels" widgets to "0" where I had been setting them to either 2 or 8. I set to hw:0 and ........WAHLAA! Finally!!! This .asoundrc actually sets up for 12 ins and 10 outs. It's including the digital I/O's as well for the needs of whomever wrote this particular one. And in point of fact the CPU usage shown is lower using this and less call backs than the "default" setting. Been farting around with it for several hours now and not one "Snap, crackle nor pop!" Been using the 2.6.7 kernel with all the realtime goodies to see if it is better now I have a good configuration for my card. It seems to be... So, it seems I'm up. (Throws salt over shoulder) I have a rehearsal tomorrow night so it will get a work out. Thanks for the replies and hints. And Thanks Jan for pointing me where I'd already been but didn't know I was there and removing all doubt! :) Russell > > > On Thu, 2004-07-08 at 15:46, Russell Hanaghan wrote: > > On Thu, 2004-07-08 at 12:20, Joe Hartley wrote: > > > On Thu, 08 Jul 2004 10:19:41 -0700 > > > Russell Hanaghan <hanaghan@xxxxxxxxxxxx> wrote: > > > > > > > Still have some light "snap, crackle and pop" problems here. They don't > > > > seem to be related to X-runs. > > > > > > I was having some big problems with noises and distortion for a while. > > > It turns out that I had some mismatches on the dB level of my gear. > > > Some worked at -10dB, some at +4dB. When I mixed and matched it, I > > > had some baaaad sounds for a while. > > > > > > I don't know how/if the 1010LT lets you change these settings, but it > > > might be worth looking at. > > > > Hmmm. I hear it mostly on the ch 1 input of the 1010. Now this channel > > is provided with a mic preamp and it is adjustable via a jumper on the > > card from (I think) +4 to -10. I use this channel because the output of > > my Takamine is relatively low. I dont hear much distortion (unless I > > thump into my axe a bit) but more subtle pops at random intervals. > > > > But I buss the other fx in seperate mixer channels in Ardour back out to > > seperate channels of the card. I am pretty sure I hear the odd pop in > > the reverb and delays as well. > > > > R~ > > > > R~ > > >
