On Tue, Dec 07, 2021 at 11:43:43AM +0530, Balakrishna Godavarthi wrote:
> Subject: arm64: dts: qcom: sc7280: Add bluetooth node on SC7280
nit: the node is added to the IDP boards, not sc7280 in general
> From: Balakrishna Godavarthi <bgodavar@xxxxxxxxxxxxx>
>
> Add bluetooth SoC WCN6750 node for SC7280 IDP boards.
>
> Signed-off-by: Balakrishna Godavarthi <bgodavar@xxxxxxxxxxxxxx>
> ---
> v3:
> * Addressed reviewers comments
that's not overly useful, instead you should describe what changed
> * Added pin config for sw_ctrl line.
> v2:
> * merged two patches into one
> * Removed unused comments
> * Removed pinmux & pin conf.
> * Addressed reviewers comments
>
> v1: initial patch
> ---
> arch/arm64/boot/dts/qcom/sc7280-idp.dts | 4 ++++
> arch/arm64/boot/dts/qcom/sc7280-idp.dtsi | 37 ++++++++++++++++++++++++++++++++
> arch/arm64/boot/dts/qcom/sc7280-idp2.dts | 4 ++++
> 3 files changed, 45 insertions(+)
>
> diff --git a/arch/arm64/boot/dts/qcom/sc7280-idp.dts b/arch/arm64/boot/dts/qcom/sc7280-idp.dts
> index 9b991ba..19bd228 100644
> --- a/arch/arm64/boot/dts/qcom/sc7280-idp.dts
> +++ b/arch/arm64/boot/dts/qcom/sc7280-idp.dts
> @@ -56,6 +56,10 @@
> };
> };
>
> +&bluetooth {
> + vddio-supply = <&vreg_l19b_1p8>;
> +};
> +
> &ipa {
> status = "okay";
> modem-init;
> diff --git a/arch/arm64/boot/dts/qcom/sc7280-idp.dtsi b/arch/arm64/boot/dts/qcom/sc7280-idp.dtsi
> index d623d71..b8b00dc 100644
> --- a/arch/arm64/boot/dts/qcom/sc7280-idp.dtsi
> +++ b/arch/arm64/boot/dts/qcom/sc7280-idp.dtsi
> @@ -14,6 +14,11 @@
> #include "pmk8350.dtsi"
>
> / {
> + aliases {
> + bluetooth0 = &bluetooth;
> + serial1 = &uart7;
> + };
> +
> gpio-keys {
> compatible = "gpio-keys";
> label = "gpio-keys";
> @@ -422,6 +427,23 @@
> <&tlmm 31 IRQ_TYPE_EDGE_FALLING>;
> pinctrl-names = "default", "sleep";
> pinctrl-1 = <&qup_uart7_sleep_cts>, <&qup_uart7_sleep_rts>, <&qup_uart7_sleep_tx>, <&qup_uart7_sleep_rx>;
> +
> + bluetooth: bluetooth {
> + compatible = "qcom,wcn6750-bt";
> + pinctrl-names = "default";
> + pinctrl-0 = <&bt_en>, <&swctrl_gpio>;
> + enable-gpios = <&tlmm 85 GPIO_ACTIVE_HIGH>;
> + swctrl-gpios = <&tlmm 86 GPIO_ACTIVE_HIGH>;
> + vddaon-supply = <&vreg_s7b_0p9>;
> + vddbtcxmx-supply = <&vreg_s7b_0p9>;
> + vddrfacmn-supply = <&vreg_s7b_0p9>;
> + vddrfa0p8-supply = <&vreg_s7b_0p9>;
> + vddrfa1p7-supply = <&vreg_s1b_1p8>;
> + vddrfa1p2-supply = <&vreg_s8b_1p2>;
> + vddrfa2p2-supply = <&vreg_s1c_2p2>;
> + vddasd-supply = <&vreg_l11c_2p8>;
> + max-speed = <3200000>;
> + };
> };
>
> /* PINCTRL - additions to nodes defined in sc7280.dtsi */
> @@ -491,6 +513,14 @@
> };
>
> &tlmm {
> + bt_en: bt-en {
> + pins = "gpio85";
> + function = "gpio";
> + drive-strength = <2>;
is it really necessary to specify the drive strength?
Documentation/devicetree/bindings/pinctrl/qcom,sc7280-pinctrl.yaml:
drive-strength:
enum: [2, 4, 6, 8, 10, 12, 14, 16]
default: 2
The default is 2, so it shouldn't be needed.
> + output-low;
> + bias-disable;
> + };
> +
> nvme_pwren: nvme-pwren {
> function = "gpio";
> };
> @@ -554,6 +584,13 @@
> */
> bias-pull-up;
> };
> +
> + swctrl_gpio: swctrl-gpio {
The 'gpio' suffix isn't really useful.
I suggest to use the signal name from the schematics "mos-sw-ctrl" or
call it "bt-sw-ctrl". If you use the schematic name then this should
be also done for the enable pin.
