Hi Thara, Thanks for the review and sorry for the late reply. On Fri, 21 May 2021 at 07:27, Thara Gopinath <thara.gopinath@xxxxxxxxxx> wrote: > > > > On 5/19/21 10:36 AM, Bhupesh Sharma wrote: > > Since the Qualcomm qce crypto driver needs the BAM dma driver to be > > setup first (to allow crypto operations), it makes sense to defer > > the qce crypto driver probing in case the BAM dma driver is not yet > > probed. > > > > Move the code leg requesting dma channels earlier in the > > probe() flow. This fixes the qce probe failure issues when both qce > > and BMA dma are compiled as static part of the kernel. > > So, I do not understand what issue you faced with the current code > ordering. When bam dma is not initialized, qce_dma_request will fail and > rest the error path kicks in. > To me the correct ordering for enabling a driver is to turn on clocks > and interconnect before requesting for dma. Unless, there is a specific > issue, I will ask for that order to be maintained. Sure. The problem I faced was the following. Let's consider the scenario where while the qce crypto driver and the interconnect are compiled as static parts of the kernel, the bam DMA driver is compiled as a module, then the -EPROBE_DEFER return leg from the qce crypto driver is very late in the probe() flow, as we first turn on the clocks and then the interconnect. Now the suggested linux deferred probe implementation is to return as early from the caling driver in case the called driver (subdev) is not yet ready. SInce the qce crypto driver requires the bam DMA to be set up first, it makes sense to move 'qce_dma_request' early in the boot flow. If it's not yet probed(), it probably doesn't make sense to set up the clks and interconnects yet in the qce driver. We can do it later when the bam DMA is setup. I have tested the following combinations with the change I made in this patchset: 1. qce - static, bam - module, interconnect - module -> qce_dma_request returned -EPROBE_DEFER 2. qce - static, bam - module, interconnect - static -> qce_dma_request returned -EPROBE_DEFER 3. qce - static, bam - static, interconnect - module -> qce_dma_request returned -EPROBE_DEFER 4. qce - static, bam - static, interconnect - static -> no -EPROBE_DEFER Thanks, Bhupesh > > Cc: Thara Gopinath <thara.gopinath@xxxxxxxxxx> > > Cc: Bjorn Andersson <bjorn.andersson@xxxxxxxxxx> > > Cc: Rob Herring <robh+dt@xxxxxxxxxx> > > Cc: Andy Gross <agross@xxxxxxxxxx> > > Cc: Herbert Xu <herbert@xxxxxxxxxxxxxxxxxxx> > > Cc: David S. Miller <davem@xxxxxxxxxxxxx> > > Cc: Stephen Boyd <sboyd@xxxxxxxxxx> > > Cc: Michael Turquette <mturquette@xxxxxxxxxxxx> > > Cc: Vinod Koul <vkoul@xxxxxxxxxx> > > Cc: dmaengine@xxxxxxxxxxxxxxx > > Cc: linux-clk@xxxxxxxxxxxxxxx > > Cc: linux-crypto@xxxxxxxxxxxxxxx > > Cc: devicetree@xxxxxxxxxxxxxxx > > Cc: linux-kernel@xxxxxxxxxxxxxxx > > Cc: bhupesh.linux@xxxxxxxxx > > Signed-off-by: Bhupesh Sharma <bhupesh.sharma@xxxxxxxxxx> > > --- > > drivers/crypto/qce/core.c | 16 +++++++++------- > > 1 file changed, 9 insertions(+), 7 deletions(-) > > > > diff --git a/drivers/crypto/qce/core.c b/drivers/crypto/qce/core.c > > index 8b3e2b4580c2..207221d5b996 100644 > > --- a/drivers/crypto/qce/core.c > > +++ b/drivers/crypto/qce/core.c > > @@ -218,6 +218,14 @@ static int qce_crypto_probe(struct platform_device *pdev) > > if (ret < 0) > > goto err_out; > > > > + /* qce driver requires BAM dma driver to be setup first. > > + * In case the dma channel are not set yet, this check > > + * helps use to return -EPROBE_DEFER earlier. > > + */ > > + ret = qce_dma_request(qce->dev, &qce->dma); > > + if (ret) > > + return ret; > > + > > qce->mem_path = devm_of_icc_get(qce->dev, "memory"); > > if (IS_ERR(qce->mem_path)) > > return dev_err_probe(dev, PTR_ERR(qce->mem_path), > > @@ -269,10 +277,6 @@ static int qce_crypto_probe(struct platform_device *pdev) > > goto err_clks_iface; > > } > > > > - ret = qce_dma_request(qce->dev, &qce->dma); > > - if (ret) > > - goto err_clks; > > - > > ret = qce_check_version(qce); > > if (ret) > > goto err_clks; > > @@ -287,12 +291,10 @@ static int qce_crypto_probe(struct platform_device *pdev) > > > > ret = qce_register_algs(qce); > > if (ret) > > - goto err_dma; > > + goto err_clks; > > > > return 0; > > > > -err_dma: > > - qce_dma_release(&qce->dma); > > err_clks: > > clk_disable_unprepare(qce->bus); > > err_clks_iface: > > > >
