On 2021-02-26 15:57, Dmitry Baryshkov wrote:
On Fri, 26 Feb 2021 at 09:59, <skakit@xxxxxxxxxxxxxx> wrote:
Hi,
On 2021-02-25 16:39, Dmitry Baryshkov wrote:
> On 24/02/2021 11:33, satya priya wrote:
>> Correct the REGULATOR_LINEAR_RANGE and n_voltges for
>> pmic5_hfsmps515 buck.
>>
>> Signed-off-by: satya priya <skakit@xxxxxxxxxxxxxx>
>> ---
>> drivers/regulator/qcom-rpmh-regulator.c | 4 ++--
>> 1 file changed, 2 insertions(+), 2 deletions(-)
>>
>> diff --git a/drivers/regulator/qcom-rpmh-regulator.c
>> b/drivers/regulator/qcom-rpmh-regulator.c
>> index 79a554f..36542c3 100644
>> --- a/drivers/regulator/qcom-rpmh-regulator.c
>> +++ b/drivers/regulator/qcom-rpmh-regulator.c
>> @@ -726,8 +726,8 @@ static const struct rpmh_vreg_hw_data
>> pmic5_ftsmps510 = {
>> static const struct rpmh_vreg_hw_data pmic5_hfsmps515 = {
>> .regulator_type = VRM,
>> .ops = &rpmh_regulator_vrm_ops,
>> - .voltage_range = REGULATOR_LINEAR_RANGE(2800000, 0, 4, 16000),
>> - .n_voltages = 5,
>> + .voltage_range = REGULATOR_LINEAR_RANGE(320000, 0, 235, 16000),
>> + .n_voltages = 236,
>
> I've checked the docs for pm8009, the chip which also uses hfsmps515
> regulators. The pdf clearly states that the 'Output voltage operating
> range' is from 2.8 V to 2.85 V.
>
> So we'd probably need to define different versions of HFS515 regulator
> data (like I had to create for pm8009-1).
>
>
The min-max voltages for S1C (PM8350c) regulator are 2190000-2210000uV
for sc7280(kodiak), so we had to modify this buck to support this
regulator.
AFAIK, this struct defines the HW constraints of a regulator, but the
platform specific min-max values can be controlled from DT files. So,
can't we modify it like above instead of adding a new definition? the
new min_uV value (32000) is anyway not exceeding the old value
(2800000)
right? please correct me if wrong.
As far as I understand for other regulators we put 'output voltage
limitations' from the docs into the regulator definition and further
constrain it by the platform device tree. Please correct me if I'm
wrong.
I see that for most of the regulators, these specifications are specific
to regulator buck (like HFS515) but not chipset specific, we set the
chipset specific(like pm8009/pm8350c) requirements from DT files.
For example:
pmic5_nldo regulator spec mentions LLIMIT= 0.32V and ULIMIT =1.304V with
step 8mV
.voltage_range = REGULATOR_LINEAR_RANGE(320000, 0, 123, 8000),
max output voltage supported by this regulator is 123*8000 + 320000 =
1304000mV which is same as mentioned in the regulator spec.
For pm8009 the data from the datasheet matches the regulators defined
in the source file. Unfortunately I don't have kodiak specs at hand.
From the HFS515 spec I got below info
"HFS510 and lower max output voltage is limited to 2.04V max, and
Yoda(pm8009) requirement was 2.4V for IOT PA and 2.85V for camera
application. Hence, HFS515 added a new register and corresponding HW
changes to support the higher voltage. Table 5‑24 shows the new
FB_RANGE bit. When configured to 0 the buck works as earlier where Vout
max = 2.04V in 8mV steps, but when configured to 1 the buck range
doubles and can now support a Vout max = 4.08V in 16mV steps."
As per above, the max output voltage supported by HFS515 buck is 4.08V
(which is kodiak pm8350c pmic's requirement).
So, we have modified the buck data to support pm8350c(palani) along with
pm8009(yoda).
Thanks,
Satya Priya
