Re: [PATCH 3/7] regulator: qcom-rpmh: Correct the pmic5_hfsmps515 buck

[Date Prev][Date Next][Thread Prev][Thread Next][Date Index][Thread Index]

 



On Fri, 26 Feb 2021 at 09:59, <skakit@xxxxxxxxxxxxxx> wrote:
>
> Hi,
>
> On 2021-02-25 16:39, Dmitry Baryshkov wrote:
> > On 24/02/2021 11:33, satya priya wrote:
> >> Correct the REGULATOR_LINEAR_RANGE and n_voltges for
> >> pmic5_hfsmps515 buck.
> >>
> >> Signed-off-by: satya priya <skakit@xxxxxxxxxxxxxx>
> >> ---
> >>   drivers/regulator/qcom-rpmh-regulator.c | 4 ++--
> >>   1 file changed, 2 insertions(+), 2 deletions(-)
> >>
> >> diff --git a/drivers/regulator/qcom-rpmh-regulator.c
> >> b/drivers/regulator/qcom-rpmh-regulator.c
> >> index 79a554f..36542c3 100644
> >> --- a/drivers/regulator/qcom-rpmh-regulator.c
> >> +++ b/drivers/regulator/qcom-rpmh-regulator.c
> >> @@ -726,8 +726,8 @@ static const struct rpmh_vreg_hw_data
> >> pmic5_ftsmps510 = {
> >>   static const struct rpmh_vreg_hw_data pmic5_hfsmps515 = {
> >>      .regulator_type = VRM,
> >>      .ops = &rpmh_regulator_vrm_ops,
> >> -    .voltage_range = REGULATOR_LINEAR_RANGE(2800000, 0, 4, 16000),
> >> -    .n_voltages = 5,
> >> +    .voltage_range = REGULATOR_LINEAR_RANGE(320000, 0, 235, 16000),
> >> +    .n_voltages = 236,
> >
> > I've checked the docs for pm8009, the chip which also uses hfsmps515
> > regulators. The pdf clearly states that the 'Output voltage operating
> > range' is from 2.8 V to 2.85 V.
> >
> > So we'd probably need to define different versions of HFS515 regulator
> > data (like I had to create for pm8009-1).
> >
> >
>
> The min-max voltages for S1C (PM8350c) regulator are 2190000-2210000uV
> for sc7280(kodiak), so we had to modify this buck to support this
> regulator.
>
> AFAIK, this struct defines the HW constraints of a regulator, but the
> platform specific min-max values can be controlled from DT files. So,
> can't we modify it like above instead of adding a new definition? the
> new min_uV value (32000) is anyway not exceeding the old value (2800000)
> right? please correct me if wrong.

As far as I understand for other regulators we put 'output voltage
limitations' from the docs into the regulator definition and further
constrain it by the platform device tree. Please correct me if I'm
wrong.
For pm8009 the data from the datasheet matches the regulators defined
in the source file. Unfortunately I don't have kodiak specs at hand.


-- 
With best wishes
Dmitry



[Index of Archives]     [Linux ARM Kernel]     [Linux ARM]     [Linux Omap]     [Fedora ARM]     [Linux for Sparc]     [IETF Annouce]     [Security]     [Bugtraq]     [Linux MIPS]     [ECOS]     [Asterisk Internet PBX]     [Linux API]

  Powered by Linux