[PATCH v9 0/4] Introduce PMIC based USB type C detection

[Date Prev][Date Next][Thread Prev][Thread Next][Date Index][Thread Index]

 



Changes in v9:
 - Fixed dt-binding to reference usb-connector from the 'connector' node,
   removed properties that didn't have further constraints (than specified in
   usb-connector.yaml), and make 'reg' a required property.
 - Moved vbus_reg get call into probe(), and will fail if the regulator is not
   available.
 - Removed some references from qcom_pmic_typec, as they were not needed after
   probe().
 - Moved interrupt registration until after all used variables were initialized.

Changes in v8:
 - Simplified some property definitions, and corrected the
   connector reference in the dt binding.

Changes in v7:
 - Fixups in qcom-pmic-typec.c to remove uncesscary includes, printk formatting,
   and revising some logic operations. 

Changes in v6:
 - Removed qcom_usb_vbus-regulator.c and qcom,usb-vbus-regulator.yaml from the
   series as they have been merged on regulator.git
 - Added separate references to the usb-connector.yaml in qcom,pmic-typec.yaml
   instead of referencing the entire schema.

Changes in v5:
 - Fix dt_binding_check warning/error in qcom,pmic-typec.yaml

Changes in v4:
 - Modified qcom,pmic-typec binding to include the SS mux and the DRD remote
   endpoint nodes underneath port@1, which is assigned to the SSUSB path
   according to usb-connector
 - Added usb-connector reference to the typec dt-binding
 - Added tags to the usb type c and vbus nodes
 - Removed "qcom" tags from type c and vbus nodes
 - Modified Kconfig module name, and removed module alias from the typec driver
 
Changes in v3:
 - Fix driver reference to match driver name in Kconfig for
   qcom_usb_vbus-regulator.c
 - Utilize regulator bitmap helpers for enable, disable and is enabled calls in
   qcom_usb_vbus-regulator.c
 - Use of_get_regulator_init_data() to initialize regulator init data, and to
   set constraints in qcom_usb_vbus-regulator.c
 - Remove the need for a local device structure in the vbus regulator driver
 
Changes in v2:
 - Use devm_kzalloc() in qcom_pmic_typec_probe()
 - Add checks to make sure return value of typec_find_port_power_role() is
   valid
 - Added a VBUS output regulator driver, which will be used by the PMIC USB
   type c driver to enable/disable the source
 - Added logic to control vbus source from the PMIC type c driver when
   UFP/DFP is detected
 - Added dt-binding for this new regulator driver
 - Fixed Kconfig typec notation to match others
 - Leave type C block disabled until enabled by a platform DTS

Wesley Cheng (4):
  usb: typec: Add QCOM PMIC typec detection driver
  dt-bindings: usb: Add Qualcomm PMIC type C controller dt-binding
  arm64: boot: dts: qcom: pm8150b: Add node for USB type C block
  arm64: boot: dts: qcom: pm8150b: Add DTS node for PMIC VBUS booster

 .../bindings/usb/qcom,pmic-typec.yaml         | 108 ++++++++
 arch/arm64/boot/dts/qcom/pm8150b.dtsi         |  13 +
 arch/arm64/boot/dts/qcom/sm8150-mtp.dts       |   4 +
 drivers/usb/typec/Kconfig                     |  12 +
 drivers/usb/typec/Makefile                    |   1 +
 drivers/usb/typec/qcom-pmic-typec.c           | 262 ++++++++++++++++++
 6 files changed, 400 insertions(+)
 create mode 100644 Documentation/devicetree/bindings/usb/qcom,pmic-typec.yaml
 create mode 100644 drivers/usb/typec/qcom-pmic-typec.c

-- 
The Qualcomm Innovation Center, Inc. is a member of the Code Aurora Forum,
a Linux Foundation Collaborative Project




[Index of Archives]     [Linux ARM Kernel]     [Linux ARM]     [Linux Omap]     [Fedora ARM]     [Linux for Sparc]     [IETF Annouce]     [Security]     [Bugtraq]     [Linux MIPS]     [ECOS]     [Asterisk Internet PBX]     [Linux API]

  Powered by Linux