Re: [PATCH v13 3/5] usb: xhci: Add support for Renesas controller with memory

[Date Prev][Date Next][Thread Prev][Thread Next][Date Index][Thread Index]

 



On Mon, 18 May 2020 at 21:57, Vinod Koul <vkoul@xxxxxxxxxx> wrote:
>
> Hi Anders,

Hi Vinod,

>
> On 18-05-20, 19:53, Anders Roxell wrote:
> > On Wed, 6 May 2020 at 08:01, Vinod Koul <vkoul@xxxxxxxxxx> wrote:
> > >
> > > Some rensas controller like uPD720201 and uPD720202 need firmware to be
> > > loaded. Add these devices in pci table and invoke renesas firmware loader
> > > functions to check and load the firmware into device memory when
> > > required.
> > >
> > > Signed-off-by: Vinod Koul <vkoul@xxxxxxxxxx>
> >
> > Hi, I got a build error when I built an arm64 allmodconfig kernel.
>
> Thanks for this. This is happening as we have default y for USB_XHCI_PCI
> and then we make USB_XHCI_PCI_RENESAS=m. That should be not allowed as
> we export as symbol so both can be inbuilt or modules but USB_XHCI_PCI=y
> and USB_XHCI_PCI_RENESAS=m cant. While it is valid that USB_XHCI_PCI=y|m
> and USB_XHCI_PCI_RENESAS=n
>
> So this seems to get fixed by below for me. I have tested with
>  - both y and m (easy)
>  - make USB_XHCI_PCI_RENESAS=n, USB_XHCI_PCI=y|m works
>  - try making USB_XHCI_PCI=y and USB_XHCI_PCI_RENESAS=m, then
>    USB_XHCI_PCI=m by kbuild :)
>  - try making USB_XHCI_PCI=m and USB_XHCI_PCI_RENESAS=y, kbuild gives
>    error prompt that it will be m due to depends
>
> Thanks to all the fixes done by Arnd which pointed me to this. Pls
> verify

I was able to build an arm64 allmodconfig kernel with this change.

Cheers,
Anders

> and I will send the fix with you as reported :)
>
> ---- >8 ----
>
> diff --git a/drivers/usb/host/Kconfig b/drivers/usb/host/Kconfig
> index b5c542d6a1c5..92783d175b3f 100644
> --- a/drivers/usb/host/Kconfig
> +++ b/drivers/usb/host/Kconfig
> @@ -40,11 +40,11 @@ config USB_XHCI_DBGCAP
>  config USB_XHCI_PCI
>         tristate
>         depends on USB_PCI
> +       depends on USB_XHCI_PCI_RENESAS || !USB_XHCI_PCI_RENESAS
>         default y
>
>  config USB_XHCI_PCI_RENESAS
>         tristate "Support for additional Renesas xHCI controller with firwmare"
> -       depends on USB_XHCI_PCI
>         ---help---
>           Say 'Y' to enable the support for the Renesas xHCI controller with
>           firwmare. Make sure you have the firwmare for the device and
>
> --
> ~Vinod



[Index of Archives]     [Linux ARM Kernel]     [Linux ARM]     [Linux Omap]     [Fedora ARM]     [Linux for Sparc]     [IETF Annouce]     [Security]     [Bugtraq]     [Linux MIPS]     [ECOS]     [Asterisk Internet PBX]     [Linux API]

  Powered by Linux