Re: [PATCH V5 3/4] backlight: qcom-wled: Add WLED5 bindings

[Date Prev][Date Next][Thread Prev][Thread Next][Date Index][Thread Index]

 



On 2020-04-15 20:42, Rob Herring wrote:
On Tue, Apr 07, 2020 at 09:17:09PM +0530, Kiran Gunda wrote:
Add WLED5 specific bindings.


checkpatch.pl complains about some trailing whitespace. The previous
patch too.

Signed-off-by: Kiran Gunda <kgunda@xxxxxxxxxxxxxx>
Signed-off-by: Subbaraman Narayanamurthy <subbaram@xxxxxxxxxxxxxx>
---
.../bindings/leds/backlight/qcom-wled.yaml | 60 ++++++++++++++++++++--
 1 file changed, 57 insertions(+), 3 deletions(-)

diff --git a/Documentation/devicetree/bindings/leds/backlight/qcom-wled.yaml b/Documentation/devicetree/bindings/leds/backlight/qcom-wled.yaml
index 770e780..5714631 100644
--- a/Documentation/devicetree/bindings/leds/backlight/qcom-wled.yaml
+++ b/Documentation/devicetree/bindings/leds/backlight/qcom-wled.yaml
@@ -21,6 +21,7 @@ properties:
       - qcom,pm8941-wled
       - qcom,pmi8998-wled
       - qcom,pm660l-wled
+      - qcom,pm8150l-wled

   reg:
     maxItems: 1
@@ -28,12 +29,13 @@ properties:
   default-brightness:
     description:
       brightness value on boot.
-    minimum: 0
-    maximum: 4095
-    default: 2048

   label: true

+  max-brightness:
+    description:
+      Maximum brightness level.
+
   qcom,cs-out:
     description:
       enable current sink output.
@@ -130,6 +132,31 @@ properties:
       This feature is not supported for WLED3.
     type: boolean

+  qcom,modulator-sel:
+    description:

Need a '|' at the end to preserve formatting.

+      Selects the modulator used for brightness modulation.
+      Allowed values are,
+           0 - Modulator A
+           1 - Modulator B
+      This property is applicable only to WLED5 peripheral.
+    allOf:
+      - $ref: /schemas/types.yaml#/definitions/uint32
+      - enum: [ 0, 1 ]
+      - default: 0
+
+  qcom,cabc-sel:
+    description:

Need a '|'.

+      Selects the CABC pin signal used for brightness modulation.
+      Allowed values are,
+           0 - CABC disabled
+           1 - CABC 1
+           2 - CABC 2
+           3 - External signal (e.g. LPG) is used for dimming
+      This property is applicable only to WLED5 peripheral.
+    allOf:
+      - $ref: /schemas/types.yaml#/definitions/uint32
+      - enum: [ 0, 1, 2, 3 ]
+
 allOf:
   - if:
       properties:
@@ -179,6 +206,33 @@ allOf:
             - const: ovp
             - const: short

+  - if:
+      properties:
+        compatible:
+          contains:
+            enum:
+              - qcom,pm8150l-wled
+
+    then:
+      properties:
+        default-brightness:
+          minimum: 0
+          maximum: 32767
+
+        max-brightness:
+          minimum: 0
+          maximum: 32767
+
+    else:
+      properties:
+        default-brightness:
+            minimum: 0
+            maximum: 4095

Wrong indentation.

+
+        max-brightness:
+          minimum: 0
+          maximum: 4095
+
 required:
   - compatible
   - reg
--
The Qualcomm Innovation Center, Inc. is a member of the Code Aurora Forum,
 a Linux Foundation Collaborative Project

Thanks for reviewing. I will submit the next revision with all the fixes.



[Index of Archives]     [Linux ARM Kernel]     [Linux ARM]     [Linux Omap]     [Fedora ARM]     [Linux for Sparc]     [IETF Annouce]     [Security]     [Bugtraq]     [Linux MIPS]     [ECOS]     [Asterisk Internet PBX]     [Linux API]

  Powered by Linux