[PATCH] drivers: thermal: step_wise: add support for hysteresis

[Amit Kucheria <amit.kucheria@xxxxxxxxxx>]

From: Ram Chandrasekar <rkumbako@xxxxxxxxxxxxxx>

Currently, step wise governor increases the mitigation when the
temperature goes above a threshold and decreases the mitigation when the
temperature goes below the threshold. If there is a case where the
temperature is wavering around the threshold, the mitigation will be
applied and removed every iteration, which is not very efficient.

The use of hysteresis temperature could avoid this ping-pong of
mitigation by relaxing the mitigation to happen only when the
temperature goes below this lower hysteresis value.

Signed-off-by: Ram Chandrasekar <rkumbako@xxxxxxxxxxxxxx>
Signed-off-by: Lina Iyer <ilina@xxxxxxxxxxxxxx>
[Rebased patch from downstream]
Signed-off-by: Amit Kucheria <amit.kucheria@xxxxxxxxxx>
---
 drivers/thermal/step_wise.c | 35 ++++++++++++++++++++++++-----------
 1 file changed, 24 insertions(+), 11 deletions(-)

diff --git a/drivers/thermal/step_wise.c b/drivers/thermal/step_wise.c
index 6e051cbd824ff..2c8a34a7cf959 100644
--- a/drivers/thermal/step_wise.c
+++ b/drivers/thermal/step_wise.c
@@ -24,7 +24,7 @@
  *       for this trip point
  *    d. if the trend is THERMAL_TREND_DROP_FULL, use lower limit
  *       for this trip point
- * If the temperature is lower than a trip point,
+ * If the temperature is lower than a hysteresis temperature,
  *    a. if the trend is THERMAL_TREND_RAISING, do nothing
  *    b. if the trend is THERMAL_TREND_DROPPING, use lower cooling
  *       state for this trip point, if the cooling state already
@@ -115,30 +115,31 @@ static void update_passive_instance(struct thermal_zone_device *tz,
 
 static void thermal_zone_trip_update(struct thermal_zone_device *tz, int trip)
 {
-	int trip_temp;
+	int trip_temp, hyst_temp;
 	enum thermal_trip_type trip_type;
 	enum thermal_trend trend;
 	struct thermal_instance *instance;
-	bool throttle = false;
+	bool throttle;
 	int old_target;
 
 	if (trip == THERMAL_TRIPS_NONE) {
-		trip_temp = tz->forced_passive;
+		hyst_temp = trip_temp = tz->forced_passive;
 		trip_type = THERMAL_TRIPS_NONE;
 	} else {
 		tz->ops->get_trip_temp(tz, trip, &trip_temp);
+		hyst_temp = trip_temp;
+		if (tz->ops->get_trip_hyst) {
+			tz->ops->get_trip_hyst(tz, trip, &hyst_temp);
+			hyst_temp = trip_temp - hyst_temp;
+		}
 		tz->ops->get_trip_type(tz, trip, &trip_type);
 	}
 
 	trend = get_tz_trend(tz, trip);
 
-	if (tz->temperature >= trip_temp) {
-		throttle = true;
-		trace_thermal_zone_trip(tz, trip, trip_type);
-	}
-
-	dev_dbg(&tz->device, "Trip%d[type=%d,temp=%d]:trend=%d,throttle=%d\n",
-				trip, trip_type, trip_temp, trend, throttle);
+	dev_dbg(&tz->device,
+		"Trip%d[type=%d,temp=%d,hyst=%d]:trend=%d,throttle=%d\n",
+		trip, trip_type, trip_temp, hyst_temp, trend, throttle);
 
 	mutex_lock(&tz->lock);
 
@@ -147,6 +148,18 @@ static void thermal_zone_trip_update(struct thermal_zone_device *tz, int trip)
 			continue;
 
 		old_target = instance->target;
+		throttle = false;
+		/*
+		 * Lower the mitigation only if the temperature
+		 * goes below the hysteresis temperature.
+		 */
+		if (tz->temperature >= trip_temp ||
+		    (tz->temperature >= hyst_temp &&
+		     old_target != THERMAL_NO_TARGET)) {
+			throttle = true;
+			trace_thermal_zone_trip(tz, trip, trip_type);
+		}
+
 		instance->target = get_target_state(instance, trend, throttle);
 		dev_dbg(&instance->cdev->device, "old_target=%d, target=%d\n",
 					old_target, (int)instance->target);
-- 
2.17.1