Hi Jeffrey, On 07/02/19 8:22 PM, Jeffrey Hugo wrote: > On 2/7/2019 1:50 AM, Alim Akhtar wrote: >> Hi Marc, >> >> On 06/02/19 9:22 PM, Marc Gonzalez wrote: >>> On 06/02/2019 16:27, Alim Akhtar wrote: >>> >>>> On 06/02/19 8:29 PM, Marc Gonzalez wrote: >>>> >>>>> [ 2.405734] regulator_disable: ENTER vdd_l26 >>>>> [ 2.405958] regulator_disable: EXIT vdd_l26 >>>>> [ 2.406032] regulator_set_load: vdd_l26 = 0 uA >>>>> [ 3.930447] ufshcd-qcom 1da4000.ufshc: ufshcd_query_attr: opcode >>>>> 0x04 for idn 13 failed, index 0, err = -11 >>>>> [ 5.434358] ufshcd-qcom 1da4000.ufshc: ufshcd_query_attr: opcode >>>>> 0x04 for idn 13 failed, index 0, err = -11 >>>>> [ 6.938318] ufshcd-qcom 1da4000.ufshc: ufshcd_query_attr: opcode >>>>> 0x04 for idn 13 failed, index 0, err = -11 >>>>> [ 6.938414] ufshcd-qcom 1da4000.ufshc: ufshcd_query_attr_retry: >>>>> query attribute, idn 13, failed with error -11 after 3 retires >>>>> [ 6.946959] ufshcd-qcom 1da4000.ufshc: >>>>> ufshcd_disable_auto_bkops: failed to enable exception event -11 >>>>> [ 6.958523] ufshcd-qcom 1da4000.ufshc: dme-peer-get: attr-id >>>>> 0x1587 failed 3 retries >>>>> [ 6.967730] ufshcd-qcom 1da4000.ufshc: dme-peer-get: attr-id >>>>> 0x1586 failed 3 retries >>>>> [ 6.975576] ufshcd-qcom 1da4000.ufshc: ufshcd_get_max_pwr_mode: >>>>> invalid max pwm tx gear read = 0 >>>>> [ 6.983306] ufshcd-qcom 1da4000.ufshc: ufshcd_probe_hba: Failed >>>>> getting max supported power mode >>>>> [ 8.506314] ufshcd-qcom 1da4000.ufshc: ufshcd_query_flag: >>>>> Sending flag query for idn 3 failed, err = -11 >>>>> [ 10.010352] ufshcd-qcom 1da4000.ufshc: ufshcd_query_flag: >>>>> Sending flag query for idn 3 failed, err = -11 >>>>> [ 11.514313] ufshcd-qcom 1da4000.ufshc: ufshcd_query_flag: >>>>> Sending flag query for idn 3 failed, err = -11 >>>>> [ 11.514412] ufshcd-qcom 1da4000.ufshc: ufshcd_query_flag_retry: >>>>> query attribute, opcode 5, idn 3, failed with error -11 after 3 >>>>> retires >>>>> [ 13.050354] ufshcd-qcom 1da4000.ufshc: >>>>> __ufshcd_query_descriptor: opcode 0x01 for idn 8 failed, index 0, >>>>> err = -11 >>>>> [ 14.554313] ufshcd-qcom 1da4000.ufshc: >>>>> __ufshcd_query_descriptor: opcode 0x01 for idn 8 failed, index 0, >>>>> err = -11 >>>>> [ 16.058313] ufshcd-qcom 1da4000.ufshc: >>>>> __ufshcd_query_descriptor: opcode 0x01 for idn 8 failed, index 0, >>>>> err = -11 >>>>> [ 16.058421] ufshcd-qcom 1da4000.ufshc: ufshcd_read_desc_param: >>>>> Failed reading descriptor. desc_id 8, desc_index 0, param_offset 0, >>>>> ret -11 >>>>> [ 16.067654] ufshcd-qcom 1da4000.ufshc: ufshcd_init_icc_levels: >>>>> Failed reading power descriptor.len = 98 ret = -11 >>>>> [ 37.074334] ufshcd-qcom 1da4000.ufshc: link startup failed 1 >>>> >>>> Can you check if your UFS device RESET_N is asserted correctly. It >>>> might >>>> be connected to some regulator and may be you can try keeping that >>>> regulator as "regulator-always-on" from your DT node. >>> >>> How do I check RESET_N? In software or hardware? >>> >> RST_N is the reset logic for UFS device core logic and it is input to >> the device from UFS host controller.So, in your platform please check if >> this line somehow connected to (pulled up) a PMIC supply. If that is the >> case, please keep that regulator ON and see if this issue is resolved. > > The reset line is routed though the global clock controller (GCC), and > must be explicitly asserted within the GCC to trigger a reset. As far > as I am aware, Linux is not touching this. > > Additionally, I fail to see how if this was a reset issue, reverting > 60f0187031c0 would have any impact (which doing so addresses our issue) > OK, that's again implementation dependent and your platform used that way. My point was to make sure that reset part is ok, if reset/power is not proper to the UFS device core logic this kind of issues comes. >>> Do you think it is not a good idea to revert >>> 60f0187031c05e04cbadffb62f557d0ff3564490 ? >>> >> Please hold on till we understand the real cause of this issue. Or we >> have a consensuses for reverting the said commit. >> Thanks! > > Did you see https://lkml.org/lkml/2019/2/5/659 where I indicated VCCQ > powers components within the host controller, and by not setting load on > the regulator properly, we are likely undervolting those components due > to the current draw? > In theory may be true. But looks like we dont have a solid evidence yet (correct me if I am wrong or misunderstood anything here) So that means its some short of hardware/board quirk, right? Can you please recheck the schematic and see what Bjorn is telling (about having right entries in the DT for regulator) resolve your issue? Marc, Can you disabled pmic on that board (hope your board boots with default PMIC supply) and see if this issue still occurs? I am just trying to understand and see what is the real cause. @Yaniv Gardi, will you be able to comment on reason for adding 60f0187031c05e04cbadffb62f557d0ff3564490 (any issue faced)?
