On 1/16/2019 3:56 AM, Marc Gonzalez wrote:
Add host controller and PHY DT nodes.
Signed-off-by: Marc Gonzalez <marc.w.gonzalez@xxxxxxx>
---
TODO: check whether the driver uses the 'resets' prop
---
arch/arm64/boot/dts/qcom/msm8998-mtp.dtsi | 20 +++++++
arch/arm64/boot/dts/qcom/msm8998.dtsi | 63 +++++++++++++++++++++++
2 files changed, 83 insertions(+)
diff --git a/arch/arm64/boot/dts/qcom/msm8998-mtp.dtsi b/arch/arm64/boot/dts/qcom/msm8998-mtp.dtsi
index 50e9033aa7f6..cd1c9e84eab7 100644
--- a/arch/arm64/boot/dts/qcom/msm8998-mtp.dtsi
+++ b/arch/arm64/boot/dts/qcom/msm8998-mtp.dtsi
@@ -257,3 +257,23 @@
pinctrl-0 = <&sdc2_clk_on &sdc2_cmd_on &sdc2_data_on &sdc2_cd_on>;
pinctrl-1 = <&sdc2_clk_off &sdc2_cmd_off &sdc2_data_off &sdc2_cd_off>;
};
+
+&ufshc {
+ vdd-hba-fixed-regulator;
Since we are not specifying the vdd anymore, I suspect this should be
dropped. Do you know of any reason why we'd still need it?
+ vcc-supply = <&vreg_l20a_2p95>;
+ vccq-supply = <&vreg_l26a_1p2>;
+ vccq2-supply = <&vreg_s4a_1p8>;
+ vcc-max-microamp = <750000>;
+ vccq-max-microamp = <560000>;
+ vccq2-max-microamp = <750000>;
+};
+
+&ufsphy {
+ vdda-phy-supply = <&vreg_l1a_0p875>;
+ vdda-pll-supply = <&vreg_l2a_1p2>;
+ vddp-ref-clk-supply = <&vreg_l26a_1p2>;
+ vdda-phy-max-microamp = <51400>;
+ vdda-pll-max-microamp = <14600>;
+ vddp-ref-clk-max-microamp = <100>;
+ vddp-ref-clk-always-on;
+};
diff --git a/arch/arm64/boot/dts/qcom/msm8998.dtsi b/arch/arm64/boot/dts/qcom/msm8998.dtsi
index 6f4f4b79853b..36fd2e614464 100644
--- a/arch/arm64/boot/dts/qcom/msm8998.dtsi
+++ b/arch/arm64/boot/dts/qcom/msm8998.dtsi
@@ -711,6 +711,69 @@
redistributor-stride = <0x0 0x20000>;
interrupts = <GIC_PPI 9 IRQ_TYPE_LEVEL_HIGH>;
};
+
+ ufshc: ufshc@1da4000 {
+ compatible = "qcom,msm8998-ufshc", "qcom,ufshc",
+ "jedec,ufs-2.0";
+ reg = <0x1da4000 0x2500>;
Bjorn would like it if reg addresses are full width, ie 0x01da4000
+ interrupts = <GIC_SPI 265 IRQ_TYPE_LEVEL_HIGH>;
+ phys = <&ufsphy_lanes>;
+ phy-names = "ufsphy";
+ lanes-per-direction = <2>;
+ power-domains = <&gcc UFS_GDSC>;
+
+ clock-names =
+ "core_clk",
+ "bus_aggr_clk",
+ "iface_clk",
+ "core_clk_unipro",
+ "ref_clk",
+ "tx_lane0_sync_clk",
+ "rx_lane0_sync_clk",
+ "rx_lane1_sync_clk";
+ clocks =
+ <&gcc GCC_UFS_AXI_CLK>,
+ <&gcc GCC_AGGRE1_UFS_AXI_CLK>,
+ <&gcc GCC_UFS_AHB_CLK>,
+ <&gcc GCC_UFS_UNIPRO_CORE_CLK>,
+ <&rpmcc RPM_SMD_LN_BB_CLK1>,
+ <&gcc GCC_UFS_TX_SYMBOL_0_CLK>,
+ <&gcc GCC_UFS_RX_SYMBOL_0_CLK>,
+ <&gcc GCC_UFS_RX_SYMBOL_1_CLK>;
+ freq-table-hz =
+ <50000000 200000000>,
+ <0 0>,
+ <0 0>,
+ <37500000 150000000>,
+ <0 0>,
+ <0 0>,
+ <0 0>,
+ <0 0>;
+
+ resets = <&gcc GCC_UFS_BCR>;
+ reset-names = "rst";
+ };
+
+ ufsphy: phy@1da7000 {
+ compatible = "qcom,sdm845-qmp-ufs-phy";
We should make an 8998 compatible. Also, don't you have phy changes
since the init sequence differs between 845 and 8998?
+ reg = <0x1da7000 0x18c>;
0x01da7000, see above comment
+ #address-cells = <1>;
+ #size-cells = <1>;
+ ranges;
+ clock-names = "ref", "ref_aux";
+ clocks =
+ <&gcc GCC_UFS_CLKREF_CLK>,
+ <&gcc GCC_UFS_PHY_AUX_CLK>;
+
+ ufsphy_lanes: lanes@1da7400 {
+ reg = <0x1da7400 0x128>,
+ <0x1da7600 0x1fc>,
+ <0x1da7c00 0x1dc>,
+ <0x1da7800 0x128>,
+ <0x1da7a00 0x1fc>;
+ #phy-cells = <0>;
+ };
+ };
};
};
--
Jeffrey Hugo
Qualcomm Datacenter Technologies as an affiliate of Qualcomm
Technologies, Inc.
Qualcomm Technologies, Inc. is a member of the
Code Aurora Forum, a Linux Foundation Collaborative Project.
