This change adds register regions for the second lane of dual-lane nodes. This additional specification is needed so that the driver can stop reaching beyond the tx and rx register allocations to get at the second lane registers in a dual-lane PHY. While in there, document #clock-cells as optional for PHYs that don't provide a pipe clock. Also, document the pcs_misc register region, which was being quietly supplied and used. Signed-off-by: Evan Green <evgreen@xxxxxxxxxxxx> --- This applies atop linux-next 20181018 with the addition of Doug's changes [1] and [2]. [1] https://lore.kernel.org/lkml/20181012213632.252346-1-dianders@xxxxxxxxxxxx/ [2] https://lore.kernel.org/lkml/20181012213926.253765-1-dianders@xxxxxxxxxxxx/ .../devicetree/bindings/phy/qcom-qmp-phy.txt | 73 +++++++++++++++++++--- 1 file changed, 65 insertions(+), 8 deletions(-) diff --git a/Documentation/devicetree/bindings/phy/qcom-qmp-phy.txt b/Documentation/devicetree/bindings/phy/qcom-qmp-phy.txt index fbc198d5dd39..297a7c753fc8 100644 --- a/Documentation/devicetree/bindings/phy/qcom-qmp-phy.txt +++ b/Documentation/devicetree/bindings/phy/qcom-qmp-phy.txt @@ -25,7 +25,7 @@ Required properties: - For all others: - The reg-names property shouldn't be defined. - - #clock-cells: must be 1 + - #clock-cells: must be 1 (PCIe and USB3 PHYs only) - Phy pll outputs a bunch of clocks for Tx, Rx and Pipe interface (for pipe based PHYs). These clock are then gate-controlled by gcc. @@ -82,23 +82,26 @@ Required nodes: - Each device node of QMP phy is required to have as many child nodes as the number of lanes the PHY has. -Required properties for child node: +Required properties for child nodes of PCIe PHYs (one child per lane): - reg: list of offset and length pairs of register sets for PHY blocks - - - index 0: tx - - index 1: rx - - index 2: pcs - - index 3: pcs_misc (optional) + tx, rx, pcs, and pcs_misc (optional). + - #phy-cells: must be 0 +Required properties for a single "lanes" child node of non-PCIe PHYs: + - reg: list of offset and length pairs of register sets for PHY blocks + For 1-lane devices: + tx, rx, pcs, and (optionally) pcs_misc + For 2-lane devices: + tx0, rx0, pcs, tx1, rx1, and (optionally) pcs_misc - #phy-cells: must be 0 -Required properties child node of pcie and usb3 qmp phys: +Required properties for child node of PCIe and USB3 qmp phys: - clocks: a list of phandles and clock-specifier pairs, one for each entry in clock-names. - clock-names: Must contain following: "pipe<lane-number>" for pipe clock specific to each lane. - clock-output-names: Name of the PHY clock that will be the parent for the above pipe clock. - For "qcom,ipq8074-qmp-pcie-phy": - "pcie20_phy0_pipe_clk" Pipe Clock parent (or) @@ -150,3 +153,57 @@ Example: ... ... }; + + phy@88eb000 { + compatible = "qcom,sdm845-qmp-usb3-uni-phy"; + reg = <0x88eb000 0x18c>; + status = "disabled"; + #clock-cells = <1>; + #address-cells = <1>; + #size-cells = <1>; + ranges; + + clocks = <&gcc GCC_USB3_SEC_PHY_AUX_CLK>, + <&gcc GCC_USB_PHY_CFG_AHB2PHY_CLK>, + <&gcc GCC_USB3_SEC_CLKREF_CLK>, + <&gcc GCC_USB3_SEC_PHY_COM_AUX_CLK>; + clock-names = "aux", "cfg_ahb", "ref", "com_aux"; + + resets = <&gcc GCC_USB3PHY_PHY_SEC_BCR>, + <&gcc GCC_USB3_PHY_SEC_BCR>; + reset-names = "phy", "common"; + + lane@88eb200 { + reg = <0x88eb200 0x128>, + <0x88eb400 0x1fc>, + <0x88eb800 0x218>, + <0x88e9600 0x70>; + #phy-cells = <0>; + clocks = <&gcc GCC_USB3_SEC_PHY_PIPE_CLK>; + clock-names = "pipe0"; + clock-output-names = "usb3_uni_phy_pipe_clk_src"; + }; + }; + + phy@1d87000 { + compatible = "qcom,sdm845-qmp-ufs-phy"; + reg = <0x1d87000 0x18c>; + #address-cells = <1>; + #size-cells = <1>; + ranges; + clock-names = "ref", + "ref_aux"; + clocks = <&gcc GCC_UFS_MEM_CLKREF_CLK>, + <&gcc GCC_UFS_PHY_PHY_AUX_CLK>; + + status = "disabled"; + + lanes@1d87400 { + reg = <0x1d87400 0x108>, + <0x1d87600 0x1e0>, + <0x1d87c00 0x1dc>, + <0x1d87800 0x108>, + <0x1d87a00 0x1e0>; + #phy-cells = <0>; + }; + }; -- 2.16.4
