Re: [PATCH v1 2/3] dt-bindings: i3c: Document Qualcomm GENI I3C master bindings

[Date Prev][Date Next][Thread Prev][Thread Next][Date Index][Thread Index]

 



On Tue, Jul 31, 2018 at 11:39:01PM -0600, Mike Shettel wrote:
> Signed-off-by: Mike Shettel <mshettel@xxxxxxxxxxxxxx>
> ---
>  .../devicetree/bindings/i3c/qcom,geni-i3c.txt      | 44 ++++++++++++++++++++++
>  1 file changed, 44 insertions(+)
>  create mode 100644 Documentation/devicetree/bindings/i3c/qcom,geni-i3c.txt
> 
> diff --git a/Documentation/devicetree/bindings/i3c/qcom,geni-i3c.txt b/Documentation/devicetree/bindings/i3c/qcom,geni-i3c.txt
> new file mode 100644
> index 0000000..8b76fda
> --- /dev/null
> +++ b/Documentation/devicetree/bindings/i3c/qcom,geni-i3c.txt
> @@ -0,0 +1,44 @@
> +Bindings for Qualcomm Geni I3C master block
> +===========================================
> +
> +Required properties:
> +--------------------
> +- compatible: shall be "qcom,geni-i3c"
> +- clocks: shall reference the se clock
> +- clock-names: shall contain clock name corresponding to the serial engine

What's the name?

> +- interrupts: the interrupt line connected to this I3C master
> +- reg: I3C master registers
> +
> +Optional properties:
> +--------------------
> +- se-clock-frequency: Source serial clock frequency to use

You should be able to figure out this frequency based on available 
dividers and the specified bus frequencies.

Or use assigned-clocks.

> +- dfs-index: Dynamic frequency scaling table index to use

Needs a vendor prefix.

> +
> +Mandatory properties defined by the generic binding (see
> +Documentation/devicetree/bindings/i3c/i3c.txt for more details):
> +
> +- #address-cells: shall be set to 3
> +- #size-cells: shall be set to 0
> +
> +Optional properties defined by the generic binding (see
> +Documentation/devicetree/bindings/i3c/i3c.txt for more details):
> +
> +- i2c-scl-hz
> +- i3c-scl-hz
 +
> +I3C device connected on the bus follow the generic description (see
> +Documentation/devicetree/bindings/i3c/i3c.txt for more details).
> +
> +Example:
> +
> +	i3c-master@0d040000 {
> +		compatible = "qcom,geni-i3c";
> +		clocks = <&clock_gcc GCC_QUPV3_WRAP0_S0_CLK>;
> +		clock-names = "se";
> +		interrupts = <GIC_SPI 356 IRQ_TYPE_LEVEL_HIGH>;
> +		reg = <0x0d040000 0x4000>;
> +		#address-cells = <3>;
> +		#size-cells = <0>;
> +		i2c-scl-hz = <100000>;
> +	};
> +
> -- 
> The Qualcomm Innovation Center, Inc. is a member of the Code Aurora Forum,
> a Linux Foundation Collaborative Project
> 



[Index of Archives]     [Linux ARM Kernel]     [Linux ARM]     [Linux Omap]     [Fedora ARM]     [Linux for Sparc]     [IETF Annouce]     [Security]     [Bugtraq]     [Linux MIPS]     [ECOS]     [Asterisk Internet PBX]     [Linux API]

  Powered by Linux