Hi Matthias, On 2018-07-31 02:25, Matthias Kaehlcke wrote:
On Fri, Jul 27, 2018 at 07:43:20PM +0530, Balakrishna Godavarthi wrote:From: Balakrishna Godavarthi <bgodavar@xxxxxxxxxxxxxx> Add support to set voltage/current of various regulators to power up/down Bluetooth chip wcn3990. Signed-off-by: Balakrishna Godavarthi <bgodavar@xxxxxxxxxxxxxx> --- Changes in v11: * removed support to read regulator currents from dts. * updated review comments.Updated regulator voltage ranges?+static int qca_wcn3990_init(struct hci_uart *hu, u32 *soc_ver) +{ + struct hci_dev *hdev = hu->hdev; + int i, ret; + + /* wcn3990 is a discrete Bluetooth chip connected to SoC. + * sometimes we will face communication synchronization issues, + * like reading version command timeouts. In which HCI_SETUP fails, + * to overcome these issues, we try to communicate by performing an + * cold power off and on. + */ + for (i = 0; i <= 3; i++) { + ret = qca_power_setup(hu, true); + if (ret) + goto regs_off; + + /* Forcefully enable wcn3990 to enter in to boot mode. */ + host_set_baudrate(hu, 2400); + ret = qca_send_power_pulse(hdev, QCA_WCN3990_POWEROFF_PULSE); + if (ret) + goto regs_off; + + qca_set_speed(hu, QCA_INIT_SPEED); + ret = qca_send_power_pulse(hdev, QCA_WCN3990_POWERON_PULSE); + if (ret) + goto regs_off; + + /* Wait for 100 ms for SoC to boot */ + msleep(100); + + /* Now the device is in ready state to communicate with host. + * To sync host with device we need to reopen port. + * Without this, we will have RTS and CTS synchronization + * issues. + */ + serdev_device_close(hu->serdev); + ret = serdev_device_open(hu->serdev); + if (ret) { + bt_dev_err(hu->hdev, "failed to open port"); + break; + } + + hci_uart_set_flow_control(hu, false); + ret = qca_read_soc_version(hdev, soc_ver); + + if (!ret) + break; + +regs_off: + bt_dev_err(hdev, "retrying to establish communication: %d", + i + 1); + qca_power_shutdown(hdev); + } + + return ret; +}I'm still not convinced that the retry loop is needed/desirable, I commented on the discussion on v10.
[Bala] : replied on v10 patch.
+static const struct qca_vreg_data qca_soc_data = { + .soc_type = QCA_WCN3990, + .vregs = (struct qca_vreg []) { + { "vddio", 1800000, 1900000, 15000 }, + { "vddxo", 1800000, 1900000, 80000 }, + { "vddrf", 1300000, 1350000, 300000 }, + { "vddch0", 3300000, 3400000, 450000 }, + },In v10 this was: { "vddio", 1800000, 1800000, 15000 }, { "vddxo", 1800000, 1800000, 80000 }, { "vddrf", 1304000, 1304000, 300000 }, { "vddch0", 3000000, 3312000, 450000 }, I don't have concerns about the new voltage ranges, but you should mention such changes in the changelog, ideally with a brief description why the change was made.
[Bala]: I missed to add, I just updated with latest values from datasheet.
-- Regards Balakrishna. -- To unsubscribe from this list: send the line "unsubscribe linux-arm-msm" in the body of a message to majordomo@xxxxxxxxxxxxxxx More majordomo info at http://vger.kernel.org/majordomo-info.html
