Hi Matthias,
On 2018-06-26 04:50, Matthias Kaehlcke wrote:
On Mon, Jun 25, 2018 at 07:10:09PM +0530, Balakrishna Godavarthi wrote:
Redefinition of qca_uart_setup will help future Qualcomm Bluetooth
SoC, to use the same function instead of duplicating the function.
Added new arguments soc_type and soc_ver to the functions.
These arguments will help to decide type of firmware files
to be loaded into Bluetooth chip.
soc_type holds the Bluetooth chip connected to APPS processor.
soc_ver holds the Bluetooth chip version.
Signed-off-by: Balakrishna Godavarthi <bgodavar@xxxxxxxxxxxxxx>
---
Changes in v8:
* updated soc_type with enum.
Changes in v7:
* initial patch
* redefined qca_uart_setup function to generic.
---
drivers/bluetooth/btqca.c | 23 ++++++++++++-----------
drivers/bluetooth/btqca.h | 13 +++++++++++--
drivers/bluetooth/hci_qca.c | 3 ++-
3 files changed, 25 insertions(+), 14 deletions(-)
diff --git a/drivers/bluetooth/btqca.c b/drivers/bluetooth/btqca.c
index c5cf9cab438a..3b25be1be19c 100644
--- a/drivers/bluetooth/btqca.c
+++ b/drivers/bluetooth/btqca.c
@@ -327,9 +327,9 @@ int qca_set_bdaddr_rome(struct hci_dev *hdev,
const bdaddr_t *bdaddr)
}
EXPORT_SYMBOL_GPL(qca_set_bdaddr_rome);
-int qca_uart_setup(struct hci_dev *hdev, uint8_t baudrate)
+int qca_uart_setup(struct hci_dev *hdev, uint8_t baudrate,
+ enum qca_btsoc_type soc_type, u32 soc_ver)
{
- u32 rome_ver = 0;
struct rome_config config;
int err;
@@ -337,19 +337,20 @@ int qca_uart_setup(struct hci_dev *hdev, uint8_t
baudrate)
config.user_baud_rate = baudrate;
- /* Get QCA version information */
- err = qca_read_soc_version(hdev, &rome_ver);
- if (err < 0 || rome_ver == 0) {
- bt_dev_err(hdev, "QCA Failed to get version %d", err);
- return err;
+ if (!soc_ver) {
+ /* Get QCA version information */
+ err = qca_read_soc_version(hdev, &soc_ver);
+ if (err < 0 || soc_ver == 0) {
+ bt_dev_err(hdev, "QCA Failed to get version (%d)", err);
+ return err;
+ }
+ bt_dev_info(hdev, "QCA controller version 0x%08x", soc_ver);
}
I thought we agreed in the discussion on "[v7,4/8] Bluetooth: btqca:
Redefine qca_uart_setup() to generic function" to call
qca_read_soc_version() in common code. Did I misinterpret that?
[Bala]: After integrating wcn3990, calling qca_read_soc_version() in
qca_setup()
is not preferable. as we will have multiple common blocks of
code in qca_setup.
calling function to set an operator speed is required in the
both the if -else blcoks
code snippet: (this i copied from previous conversation, before this
patch series. so you may see a different function call)
static int qca_setup(struct hci_uart *hu)
{
...
qcadev = serdev_device_get_drvdata(hu->serdev);
/* Patch downloading has to be done without IBS mode */
clear_bit(STATE_IN_BAND_SLEEP_ENABLED, &qca->flags);
/* Setup initial baudrate */
qca_set_speed(hu, speed, QCA_INIT_SPEED);
if (qcadev->btsoc_type == QCA_WCN3990) {
bt_dev_dbg(hdev, "setting up wcn3990");
hci_uart_set_flow_control(hu, true);
ret = qca_send_vendor_cmd(hdev,
QCA_WCN3990_POWERON_PULSE);
if (ret) {
bt_dev_err(hdev, "failed to send power on
command");
return ret;
}
serdev_device_close(hu->serdev);
ret = serdev_device_open(hu->serdev);
if (ret) {
bt_dev_err(hdev, "failed to open port");
return ret;
}
msleep(100);
speed = qca_get_speed(hu, QCA_INIT_SPEED);
if (speed)
qca_set_speed(hu, speed, QCA_INIT_SPEED);
hci_uart_set_flow_control(hu, false);
} else {
bt_dev_info(hdev, "ROME setup");
/* Setup user speed if needed */
speed = qca_get_speed(hu, QCA_OPER_SPEED);
if (speed) {
ret = qca_set_speed(hu, speed, QCA_OPER_SPEED);
if (ret)
return ret;
qca_baudrate = qca_get_baudrate_value(speed);
}
}
ret = qca_read_soc_version(hdev, &soc_ver);
if (ret < 0 || soc_ver == 0) {
bt_dev_err(hdev, "Failed to get version %d", ret);
return ret;
}
bt_dev_info(hdev, "wcn3990 controller version 0x%08x", soc_ver);
if (qcadev->btsoc_type == QCA_WCN3990) {
hci_uart_set_flow_control(hu, true);
/* Setup user speed if needed */
speed = qca_get_speed(hu, QCA_OPER_SPEED);
if (speed) {
ret = qca_set_speed(hu, speed, QCA_OPER_SPEED);
if (ret)
return ret;
qca_baudrate = qca_get_baudrate_value(speed);
}
/* Setup patch / NVM configurations */
ret = qca_uart_setup(hdev, qca_baudrate, qcadev->btsoc_type,
soc_ver);
if (!ret) {
set_bit(STATE_IN_BAND_SLEEP_ENABLED, &qca->flags);
qca_debugfs_init(hdev);
} else if (ret == -ENOENT) {
/* No patch/nvm-config found, run with original
fw/config */
ret = 0;
} else if (ret == -EAGAIN) {
/*
...
}
diff --git a/drivers/bluetooth/btqca.h b/drivers/bluetooth/btqca.h
index 5c9851b11838..24d6667eecf1 100644
--- a/drivers/bluetooth/btqca.h
+++ b/drivers/bluetooth/btqca.h
...
-static inline int qca_uart_setup(struct hci_dev *hdev, uint8_t
baudrate)
+static inline int qca_uart_setup(struct hci_dev *hdev, uint8_t
baudrate,
+ enum qca_btsoc_type soc_type, u32 soc_ver);
Remove trailing semicolon.
[Bala]: i didn't get you.
--
Regards
Balakrishna.
--
To unsubscribe from this list: send the line "unsubscribe linux-arm-msm" in
the body of a message to majordomo@xxxxxxxxxxxxxxx
More majordomo info at http://vger.kernel.org/majordomo-info.html
