On Mon, Jun 25, 2018 at 07:10:13PM +0530, Balakrishna Godavarthi wrote:
> Add support to set voltage/current of various regulators
> to power up/down Bluetooth chip wcn3990.
>
> Signed-off-by: Balakrishna Godavarthi <bgodavar@xxxxxxxxxxxxxx>
> ---
> changes in v8:
> * closing qca buffer, if qca_power_setup fails
> * chnaged ibs start timer function call location.
> * updated review comments.
>
> changes in v7:
> * addressed review comments.
>
> changes in v6:
> * Hooked up qca_power to qca_serdev.
> * renamed all the naming inconsistency functions with qca_*
> * leveraged common code of ROME for wcn3990.
> * created wrapper functions for re-usable blocks.
> * updated function of _*regulator_enable and _*regualtor_disable.
> * removed redundant comments and functions.
> * addressed review comments.
>
> Changes in v5:
> * updated regulator vddpa min_uV to 1304000.
> * addressed review comments.
>
> Changes in v4:
> * Segregated the changes of btqca from hci_qca
> * rebased all changes on top of bluetooth-next.
> * addressed review comments.
>
> ---
> diff --git a/drivers/bluetooth/hci_qca.c b/drivers/bluetooth/hci_qca.c
> index 28187a89b850..bd4c9a78716f 100644
> --- a/drivers/bluetooth/hci_qca.c
> +++ b/drivers/bluetooth/hci_qca.c
> ...
> +static int qca_send_vendor_cmd(struct hci_dev *hdev, u8 cmd)
> +{
> + struct hci_uart *hu = hci_get_drvdata(hdev);
> + struct qca_data *qca = hu->priv;
> + struct sk_buff *skb;
> +
> + bt_dev_dbg(hdev, "sending command %02x to SoC", cmd);
> +
> + skb = bt_skb_alloc(sizeof(cmd), GFP_KERNEL);
> + if (!skb) {
> + bt_dev_err(hdev, "Failed to allocate memory for vendor packet");
As mentioned on v7, custom OOM messages should be avoided.
> static int qca_set_speed(struct hci_uart *hu, enum qca_speed_type speed_type)
> {
> + struct qca_serdev *qcadev;
> unsigned int speed, qca_baudrate;
> int ret;
>
> @@ -971,6 +1054,13 @@ static int qca_set_speed(struct hci_uart *hu, enum qca_speed_type speed_type)
> return 0;
> }
>
> + qcadev = serdev_device_get_drvdata(hu->serdev);
> + /* Disabling hardware flow control is preferred while
> + * sending change baud rate command to SoC.
> + */
Is it only preferred or must be?
> + if (qcadev->btsoc_type == QCA_WCN3990)
> + hci_uart_set_flow_control(hu, true);
> +
nit: consider doing this just before qca_set_baudrate(). It doesn't
make a difference but leaves it clearer what exactly needs to be
'protected' (analogy to locking).
> qca_baudrate = qca_get_baudrate_value(speed);
> bt_dev_info(hu->hdev, "Set UART speed to %d", speed);
> ret = qca_set_baudrate(hu->hdev, qca_baudrate);
> @@ -980,8 +1070,10 @@ static int qca_set_speed(struct hci_uart *hu, enum qca_speed_type speed_type)
> }
>
> host_set_baudrate(hu, speed);
> + if (qcadev->btsoc_type == QCA_WCN3990)
> + hci_uart_set_flow_control(hu, false);
> static int qca_setup(struct hci_uart *hu)
> @@ -989,10 +1081,11 @@ static int qca_setup(struct hci_uart *hu)
> struct hci_dev *hdev = hu->hdev;
> struct qca_data *qca = hu->priv;
> unsigned int speed, qca_baudrate = QCA_BAUDRATE_115200;
> + struct qca_serdev *qcadev;
> int ret;
> int soc_ver = 0;
>
> - bt_dev_info(hdev, "ROME setup");
> + qcadev = serdev_device_get_drvdata(hu->serdev);
>
> /* Patch downloading has to be done without IBS mode */
> clear_bit(STATE_IN_BAND_SLEEP_ENABLED, &qca->flags);
> @@ -1000,6 +1093,35 @@ static int qca_setup(struct hci_uart *hu)
> /* Setup initial baudrate */
> qca_set_speed(hu, QCA_INIT_SPEED);
>
> + if (qcadev->btsoc_type == QCA_WCN3990) {
> + bt_dev_dbg(hdev, "setting up wcn3990");
> + hci_uart_set_flow_control(hu, true);
> + ret = qca_send_vendor_cmd(hdev, QCA_WCN3990_POWERON_PULSE);
> + if (ret)
> + return ret;
> +
> + hci_uart_set_flow_control(hu, false);
> + serdev_device_close(hu->serdev);
> + ret = serdev_device_open(hu->serdev);
> + if (ret) {
> + bt_dev_err(hdev, "failed to open port");
> + return ret;
> + }
> +
> + msleep(100);
Is the sleep really related with _open() or is it rather that the
device needs to settle after the power on pulse? In the latter case
I'd suggest to do the sleep before _open(), if it doesn't make a
functional difference (makes the code a bit more self documenting).
> + /* Setup initial baudrate */
> + qca_set_speed(hu, QCA_INIT_SPEED);
> + hci_uart_set_flow_control(hu, false);
This is still a bit noisy with all the open/close and flow control
stuff. If I understand correctly this essentially switches the
controller on (or resets it?) and brings it (and the driver) into a
sane state. Would it make sense to move the above block into a
wcn3990_init/reset() or so?
--
To unsubscribe from this list: send the line "unsubscribe linux-arm-msm" in
the body of a message to majordomo@xxxxxxxxxxxxxxx
More majordomo info at http://vger.kernel.org/majordomo-info.html
