This gets host USB working again for me on db410c on master.
This reverts commit ed75d6a969056cc8f5dd2df3af6c75b792b9116b.
---
arch/arm64/boot/dts/qcom/apq8016-sbc.dtsi | 34 ++++++++---------
arch/arm64/boot/dts/qcom/msm8916.dtsi | 62 ++++++++++++++++---------------
2 files changed, 49 insertions(+), 47 deletions(-)
diff --git a/arch/arm64/boot/dts/qcom/apq8016-sbc.dtsi b/arch/arm64/boot/dts/qcom/apq8016-sbc.dtsi
index bd310ac1967a..f326f4fb4d72 100644
--- a/arch/arm64/boot/dts/qcom/apq8016-sbc.dtsi
+++ b/arch/arm64/boot/dts/qcom/apq8016-sbc.dtsi
@@ -215,16 +215,22 @@
usb@78d9000 {
extcon = <&usb_id>, <&usb_id>;
status = "okay";
- adp-disable;
- hnp-disable;
- srp-disable;
- ulpi {
- phy {
- v1p8-supply = <&pm8916_l7>;
- v3p3-supply = <&pm8916_l13>;
- extcon = <&usb_id>;
- };
- };
+ };
+
+ ehci@78d9000 {
+ status = "okay";
+ };
+
+ phy@78d9000 {
+ v1p8-supply = <&pm8916_l7>;
+ v3p3-supply = <&pm8916_l13>;
+ vddcx-supply = <&pm8916_s1>;
+ extcon = <&usb_id>, <&usb_id>;
+ dr_mode = "otg";
+ status = "okay";
+ switch-gpio = <&pm8916_gpios 4 GPIO_ACTIVE_HIGH>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&usb_sw_sel_pm>;
};
lpass@07708000 {
@@ -342,14 +348,6 @@
pinctrl-0 = <&usb_id_default>;
};
- usb-switch {
- compatible = "toshiba,tc7usb40mu";
- switch-gpios = <&pm8916_gpios 4 GPIO_ACTIVE_HIGH>;
- extcon = <&usb_id>;
- pinctrl-names = "default";
- pinctrl-0 = <&usb_sw_sel_pm>;
- };
-
hdmi-out {
compatible = "hdmi-connector";
type = "a";
diff --git a/arch/arm64/boot/dts/qcom/msm8916.dtsi b/arch/arm64/boot/dts/qcom/msm8916.dtsi
index 5c36a0934989..a4de94f9fecb 100644
--- a/arch/arm64/boot/dts/qcom/msm8916.dtsi
+++ b/arch/arm64/boot/dts/qcom/msm8916.dtsi
@@ -566,40 +566,44 @@
status = "disabled";
};
- otg: usb@78d9000 {
+ usb_dev: usb@78d9000 {
compatible = "qcom,ci-hdrc";
- reg = <0x78d9000 0x200>,
- <0x78d9200 0x200>;
+ reg = <0x78d9000 0x400>;
+ dr_mode = "peripheral";
+ interrupts = <GIC_SPI 134 IRQ_TYPE_LEVEL_HIGH>;
+ usb-phy = <&usb_otg>;
+ status = "disabled";
+ };
+
+ usb_host: ehci@78d9000 {
+ compatible = "qcom,ehci-host";
+ reg = <0x78d9000 0x400>;
+ interrupts = <GIC_SPI 134 IRQ_TYPE_LEVEL_HIGH>;
+ usb-phy = <&usb_otg>;
+ status = "disabled";
+ };
+
+ usb_otg: phy@78d9000 {
+ compatible = "qcom,usb-otg-snps";
+ reg = <0x78d9000 0x400>;
interrupts = <GIC_SPI 134 IRQ_TYPE_LEVEL_HIGH>,
<GIC_SPI 140 IRQ_TYPE_LEVEL_HIGH>;
+
+ qcom,vdd-levels = <500000 1000000 1320000>;
+ qcom,phy-init-sequence = <0x44 0x6B 0x24 0x13>;
+ dr_mode = "peripheral";
+ qcom,otg-control = <2>; // PMIC
+ qcom,manual-pullup;
+
clocks = <&gcc GCC_USB_HS_AHB_CLK>,
- <&gcc GCC_USB_HS_SYSTEM_CLK>;
- clock-names = "iface", "core";
- assigned-clocks = <&gcc GCC_USB_HS_SYSTEM_CLK>;
- assigned-clock-rates = <80000000>;
- resets = <&gcc GCC_USB_HS_BCR>;
- reset-names = "core";
- phy_type = "ulpi";
- dr_mode = "otg";
- ahb-burst-config = <0>;
- phy-names = "usb-phy";
- phys = <&usb_hs_phy>;
- status = "disabled";
- #reset-cells = <1>;
+ <&gcc GCC_USB_HS_SYSTEM_CLK>,
+ <&gcc GCC_USB2A_PHY_SLEEP_CLK>;
+ clock-names = "iface", "core", "sleep";
- ulpi {
- usb_hs_phy: phy {
- compatible = "qcom,usb-hs-phy-msm8916",
- "qcom,usb-hs-phy";
- #phy-cells = <0>;
- clocks = <&xo_board>, <&gcc GCC_USB2A_PHY_SLEEP_CLK>;
- clock-names = "ref", "sleep";
- resets = <&gcc GCC_USB2A_PHY_BCR>, <&otg 0>;
- reset-names = "phy", "por";
- qcom,init-seq = /bits/ 8 <0x0 0x44
- 0x1 0x6b 0x2 0x24 0x3 0x13>;
- };
- };
+ resets = <&gcc GCC_USB2A_PHY_BCR>,
+ <&gcc GCC_USB_HS_BCR>;
+ reset-names = "phy", "link";
+ status = "disabled";
};
intc: interrupt-controller@b000000 {
--
2.13.0
--
To unsubscribe from this list: send the line "unsubscribe linux-arm-msm" in
the body of a message to majordomo@xxxxxxxxxxxxxxx
More majordomo info at http://vger.kernel.org/majordomo-info.html
