Re: [PATCH 1/8] PM / Domains: Make genpd state allocation dynamic

[Date Prev][Date Next][Thread Prev][Thread Next][Date Index][Thread Index]

 



On 6 October 2016 at 17:40, Lina Iyer <lina.iyer@xxxxxxxxxx> wrote:
> On Thu, Oct 06 2016 at 02:37 -0600, Ulf Hansson wrote:
>>
>> On 5 October 2016 at 22:31, Lina Iyer <lina.iyer@xxxxxxxxxx> wrote:
>>>
>>> Allow PM Domain states to be defined dynamically by the drivers. This
>>> removes the limitation on the maximum number of states possible for a
>>> domain.
>>>
>>> Cc: Axel Haslam <ahaslam+renesas@xxxxxxxxxxxx>
>>> Suggested-by: Ulf Hansson <ulf.hansson@xxxxxxxxxx>
>>> Signed-off-by: Lina Iyer <lina.iyer@xxxxxxxxxx>
>
> <...>
>>>
>>> -#define GENPD_MAX_NUM_STATES   8 /* Number of possible low power states
>>> */
>>> -
>>>  enum gpd_status {
>>>         GPD_STATE_ACTIVE = 0,   /* PM domain is active */
>>>         GPD_STATE_POWER_OFF,    /* PM domain is off */
>>> @@ -70,7 +68,7 @@ struct generic_pm_domain {
>>>         void (*detach_dev)(struct generic_pm_domain *domain,
>>>                            struct device *dev);
>>>         unsigned int flags;             /* Bit field of configs for genpd
>>> */
>>> -       struct genpd_power_state states[GENPD_MAX_NUM_STATES];
>>> +       struct genpd_power_state *states;
>>>         unsigned int state_count; /* number of states */
>>>         unsigned int state_idx; /* state that genpd will go to when off
>>> */
>>>
>>> --
>>> 2.7.4
>>>
>>
>> In general I like the improvement, but..
>>
>> This change implies that ->states may very well be NULL. This isn't
>> validated by genpd's internal logic when power off/on the domain
>> (genpd_power_on|off(), __default_power_down_ok()). You need to fix
>> this, somehow.
>>
> Good point.
>
>> Perhaps the easiest solutions is, when pm_genpd_init() finds that
>> ->state is NULL, that we allocate a struct genpd_power_state with
>> array size of 1 and assign it to ->states. Although, doing this also
>> means you need to track that genpd was responsible for the the
>> allocation, so it must also free the data from within genpd_remove().
>>
>> Unless you have other ideas!?
>>
> I can think of some hacks, but they are uglier than the problem we are
> trying to solve. We could drop this patch. Real world situations would
> not have more than 8 states and if there is one, we can think about it
> then.

The problem with the current approach is that we waste some memory as
we always have an array of 8 states per genpd. In the worst case,
which currently is the most common case, only 1 out of 8 states is
being used.

So, let's not be lazy here and instead take the opportunity to fix
this, and especially I think this makes sense, before we go on and add
the DT parsing of the domain-idle-states.

The more sophisticated method would probably be to use kobject/kref,
but let's not go there for now. Instead let's try an easy method of
just tracking whether the allocations had been made internally by
genpd, via adding a "bool state_allocated to the struct
generic_pm_domain. Would that work?

Kind regards
Uffe
--
To unsubscribe from this list: send the line "unsubscribe linux-arm-msm" in
the body of a message to majordomo@xxxxxxxxxxxxxxx
More majordomo info at  http://vger.kernel.org/majordomo-info.html



[Index of Archives]     [Linux ARM Kernel]     [Linux ARM]     [Linux Omap]     [Fedora ARM]     [Linux for Sparc]     [IETF Annouce]     [Security]     [Bugtraq]     [Linux MIPS]     [ECOS]     [Asterisk Internet PBX]     [Linux API]

  Powered by Linux