Tagging on to Archit's patchset here.
Add DSI and panel nodes to get graphics up and running
on the Nexus7.
This still depends on the panel driver being present
(currently under review) along with the rpmclk code.
Feedback would be appreciated here!
Cc: Archit Taneja <architt@xxxxxxxxxxxxxx>
Cc: vinay simha <vinaysimha@xxxxxxxxxxxxxxxxxxxx>
Cc: andy.gross@xxxxxxxxxx
Cc: robdclark@xxxxxxxxx
Cc: linux-arm-msm@xxxxxxxxxxxxxxx
Cc: dri-devel@xxxxxxxxxxxxxxxxxxxxx
Signed-off-by: John Stultz <john.stultz@xxxxxxxxxx>
---
arch/arm/boot/dts/qcom-apq8064-asus-nexus7-flo.dts | 78 +++++++++++++++++++++-
1 file changed, 76 insertions(+), 2 deletions(-)
diff --git a/arch/arm/boot/dts/qcom-apq8064-asus-nexus7-flo.dts b/arch/arm/boot/dts/qcom-apq8064-asus-nexus7-flo.dts
index ff856c3..e25a764 100644
--- a/arch/arm/boot/dts/qcom-apq8064-asus-nexus7-flo.dts
+++ b/arch/arm/boot/dts/qcom-apq8064-asus-nexus7-flo.dts
@@ -27,6 +27,18 @@
regulator-boot-on;
};
+ vcc_1p8v: regulator-fixed@2 {
+ compatible = "regulator-fixed";
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+ regulator-name = "vcc_1p8v";
+ regulator-type = "voltage";
+ startup-delay-us = <0>;
+ gpio = <&pm8921_gpio 23 GPIO_ACTIVE_HIGH>;
+ enable-active-high;
+ regulator-boot-on;
+ };
+
gpio-keys {
compatible = "gpio-keys";
volume_up {
@@ -99,6 +111,7 @@
l2 {
regulator-min-microvolt = <1200000>;
regulator-max-microvolt = <1200000>;
+ regulator-always-on;
};
/* msm_otg-HSUSB_3p3 */
@@ -133,13 +146,14 @@
regulator-min-microvolt = <3000000>;
regulator-max-microvolt = <3000000>;
bias-pull-down;
+ regulator-always-on;
};
/* pwm_power for backlight */
l17 {
regulator-min-microvolt = <3000000>;
- regulator-max-microvolt = <3600000>;
- bias-pull-down;
+ regulator-max-microvolt = <3000000>;
+ regulator-always-on;
};
/* camera, qdsp6 */
@@ -184,6 +198,66 @@
};
};
+ mdp@5100000 {
+ status = "okay";
+ ports {
+ port@1 {
+ mdp_dsi1_out: endpoint {
+ remote-endpoint = <&dsi0_in>;
+ };
+ };
+ };
+ };
+
+ dsi0: qcom,mdss_dsi@4700000 {
+ status = "okay";
+ vdda-supply = <&pm8921_l2>;/*VDD_MIPI1 to 4*/
+ vdd-supply = <&pm8921_l8>;
+ vddio-supply = <&pm8921_lvs7>;
+ avdd-supply = <&pm8921_l11>;
+ vcss-supply = <&ext_3p3v>;
+
+ panel@0 {
+ reg = <0>;
+ compatible = "jdi,lt070me05000";
+
+ pinctrl-names = "default";
+ pinctrl-0 = <&dsi_panel_pinctrl>;
+
+ vddp-supply = <&pm8921_l17>;
+ dcdc_en-supply = <&pm8921_lvs7>;
+ vcc-supply = <&vcc_1p8v>;
+
+ reset-gpios = <&tlmm_pinmux 54 0>;
+ enable-gpios = <&pm8921_gpio 36 GPIO_ACTIVE_HIGH>;
+
+ port {
+ panel_in: endpoint {
+ remote-endpoint = <&dsi0_out>;
+ };
+ };
+ };
+ ports {
+ port@0 {
+ dsi0_in: endpoint {
+ remote-endpoint = <&mdp_dsi1_out>;
+ };
+ };
+
+ port@1 {
+ dsi0_out: endpoint {
+ remote-endpoint = <&panel_in>;
+ data-lanes = <0 1 2 3>;
+ };
+ };
+ };
+ };
+
+ mdp_dsi_phy0: qcom,mdss_dsi_phy@4700200 {
+ status = "okay";
+ vddio-supply = <&pm8921_lvs7>;/*VDD_PLL2_1 to 7*/
+ };
+
gsbi@16200000 {
status = "okay";
qcom,mode = <GSBI_PROT_I2C>;
--
1.9.1
--
To unsubscribe from this list: send the line "unsubscribe linux-arm-msm" in
the body of a message to majordomo@xxxxxxxxxxxxxxx
More majordomo info at http://vger.kernel.org/majordomo-info.html
