Add support for DSI PHY v7.0 on Qualcomm SM8750 SoC which comes with an
incompatible hardware interface change:
ICODE_ACCUM_STATUS_LOW and ALOG_OBSV_BUS_STATUS_1 registers - their
offsets were just switched. Currently these registers are not used in
the driver, so the easiest is to document both but keep them commented
out to avoid conflict.
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@xxxxxxxxxx>
---
Changes in v2:
1.
---
drivers/gpu/drm/msm/dsi/phy/dsi_phy.c | 2 +
drivers/gpu/drm/msm/dsi/phy/dsi_phy.h | 1 +
drivers/gpu/drm/msm/dsi/phy/dsi_phy_7nm.c | 79 ++++++++++++++++++++--
.../gpu/drm/msm/registers/display/dsi_phy_7nm.xml | 14 ++++
4 files changed, 90 insertions(+), 6 deletions(-)
diff --git a/drivers/gpu/drm/msm/dsi/phy/dsi_phy.c b/drivers/gpu/drm/msm/dsi/phy/dsi_phy.c
index c0bcc68289633fd7506ce4f1f963655d862e8f08..60571237efc4d332959ac76ff1d6d6245f688469 100644
--- a/drivers/gpu/drm/msm/dsi/phy/dsi_phy.c
+++ b/drivers/gpu/drm/msm/dsi/phy/dsi_phy.c
@@ -593,6 +593,8 @@ static const struct of_device_id dsi_phy_dt_match[] = {
.data = &dsi_phy_4nm_8550_cfgs },
{ .compatible = "qcom,sm8650-dsi-phy-4nm",
.data = &dsi_phy_4nm_8650_cfgs },
+ { .compatible = "qcom,sm8750-dsi-phy-3nm",
+ .data = &dsi_phy_3nm_8750_cfgs },
#endif
{}
};
diff --git a/drivers/gpu/drm/msm/dsi/phy/dsi_phy.h b/drivers/gpu/drm/msm/dsi/phy/dsi_phy.h
index 8985818bb2e0934e9084a420c90e2269c2e1c414..fdb6c648e16f25812a2948053f31186d4c0d4413 100644
--- a/drivers/gpu/drm/msm/dsi/phy/dsi_phy.h
+++ b/drivers/gpu/drm/msm/dsi/phy/dsi_phy.h
@@ -60,6 +60,7 @@ extern const struct msm_dsi_phy_cfg dsi_phy_5nm_8350_cfgs;
extern const struct msm_dsi_phy_cfg dsi_phy_5nm_8450_cfgs;
extern const struct msm_dsi_phy_cfg dsi_phy_4nm_8550_cfgs;
extern const struct msm_dsi_phy_cfg dsi_phy_4nm_8650_cfgs;
+extern const struct msm_dsi_phy_cfg dsi_phy_3nm_8750_cfgs;
struct msm_dsi_dphy_timing {
u32 clk_zero;
diff --git a/drivers/gpu/drm/msm/dsi/phy/dsi_phy_7nm.c b/drivers/gpu/drm/msm/dsi/phy/dsi_phy_7nm.c
index 6d287cfb0148bdb0b1c64675dfe7fa69d3faba2d..b626989cb3d505f1c53f212dba130e3d685fe59c 100644
--- a/drivers/gpu/drm/msm/dsi/phy/dsi_phy_7nm.c
+++ b/drivers/gpu/drm/msm/dsi/phy/dsi_phy_7nm.c
@@ -50,6 +50,8 @@
#define DSI_PHY_7NM_QUIRK_V4_3 BIT(3)
/* Hardware is V5.2 */
#define DSI_PHY_7NM_QUIRK_V5_2 BIT(4)
+/* Hardware is V7.0 */
+#define DSI_PHY_7NM_QUIRK_V7_0 BIT(5)
struct dsi_pll_config {
bool enable_ssc;
@@ -128,9 +130,30 @@ static void dsi_pll_calc_dec_frac(struct dsi_pll_7nm *pll, struct dsi_pll_config
dec_multiple = div_u64(pll_freq * multiplier, divider);
dec = div_u64_rem(dec_multiple, multiplier, &frac);
- if (pll->phy->cfg->quirks & DSI_PHY_7NM_QUIRK_PRE_V4_1)
+ if (pll->phy->cfg->quirks & DSI_PHY_7NM_QUIRK_PRE_V4_1) {
config->pll_clock_inverters = 0x28;
- else if ((pll->phy->cfg->quirks & DSI_PHY_7NM_QUIRK_V5_2)) {
+ } else if ((pll->phy->cfg->quirks & DSI_PHY_7NM_QUIRK_V7_0)) {
+ if (pll_freq < 163000000ULL)
+ config->pll_clock_inverters = 0xa0;
+ else if (pll_freq < 175000000ULL)
+ config->pll_clock_inverters = 0x20;
+ else if (pll_freq < 325000000ULL)
+ config->pll_clock_inverters = 0xa0;
+ else if (pll_freq < 350000000ULL)
+ config->pll_clock_inverters = 0x20;
+ else if (pll_freq < 650000000ULL)
+ config->pll_clock_inverters = 0xa0;
+ else if (pll_freq < 700000000ULL)
+ config->pll_clock_inverters = 0x20;
+ else if (pll_freq < 1300000000ULL)
+ config->pll_clock_inverters = 0xa0;
+ else if (pll_freq < 2500000000ULL)
+ config->pll_clock_inverters = 0x20;
+ else if (pll_freq < 4000000000ULL)
+ config->pll_clock_inverters = 0x00;
+ else
+ config->pll_clock_inverters = 0x40;
+ } else if ((pll->phy->cfg->quirks & DSI_PHY_7NM_QUIRK_V5_2)) {
if (pll_freq <= 1300000000ULL)
config->pll_clock_inverters = 0xa0;
else if (pll_freq <= 2500000000ULL)
@@ -249,7 +272,8 @@ static void dsi_pll_config_hzindep_reg(struct dsi_pll_7nm *pll)
vco_config_1 = 0x01;
}
- if ((pll->phy->cfg->quirks & DSI_PHY_7NM_QUIRK_V5_2)) {
+ if ((pll->phy->cfg->quirks & DSI_PHY_7NM_QUIRK_V5_2) ||
+ (pll->phy->cfg->quirks & DSI_PHY_7NM_QUIRK_V7_0)) {
if (pll->vco_current_rate < 1557000000ULL)
vco_config_1 = 0x08;
else
@@ -624,6 +648,7 @@ static int dsi_7nm_pll_restore_state(struct msm_dsi_phy *phy)
static int dsi_7nm_set_usecase(struct msm_dsi_phy *phy)
{
struct dsi_pll_7nm *pll_7nm = to_pll_7nm(phy->vco_hw);
+ void __iomem *base = phy->base;
u32 data = 0x0; /* internal PLL */
DBG("DSI PLL%d", pll_7nm->phy->id);
@@ -633,6 +658,9 @@ static int dsi_7nm_set_usecase(struct msm_dsi_phy *phy)
break;
case MSM_DSI_PHY_MASTER:
pll_7nm->slave = pll_7nm_list[(pll_7nm->phy->id + 1) % DSI_MAX];
+ /* v7.0: Enable ATB_EN0 and alternate clock output to external phy */
+ if (phy->cfg->quirks & DSI_PHY_7NM_QUIRK_V7_0)
+ writel(0x07, base + REG_DSI_7nm_PHY_CMN_CTRL_5);
break;
case MSM_DSI_PHY_SLAVE:
data = 0x1; /* external PLL */
@@ -914,7 +942,8 @@ static int dsi_7nm_phy_enable(struct msm_dsi_phy *phy,
/* Request for REFGEN READY */
if ((phy->cfg->quirks & DSI_PHY_7NM_QUIRK_V4_3) ||
- (phy->cfg->quirks & DSI_PHY_7NM_QUIRK_V5_2)) {
+ (phy->cfg->quirks & DSI_PHY_7NM_QUIRK_V5_2) ||
+ (phy->cfg->quirks & DSI_PHY_7NM_QUIRK_V7_0)) {
writel(0x1, phy->base + REG_DSI_7nm_PHY_CMN_GLBL_DIGTOP_SPARE10);
udelay(500);
}
@@ -948,7 +977,20 @@ static int dsi_7nm_phy_enable(struct msm_dsi_phy *phy,
lane_ctrl0 = 0x1f;
}
- if ((phy->cfg->quirks & DSI_PHY_7NM_QUIRK_V5_2)) {
+ if ((phy->cfg->quirks & DSI_PHY_7NM_QUIRK_V7_0)) {
+ if (phy->cphy_mode) {
+ /* TODO: different for second phy */
+ vreg_ctrl_0 = 0x57;
+ vreg_ctrl_1 = 0x41;
+ glbl_rescode_top_ctrl = 0x3d;
+ glbl_rescode_bot_ctrl = 0x38;
+ } else {
+ vreg_ctrl_0 = 0x56;
+ vreg_ctrl_1 = 0x19;
+ glbl_rescode_top_ctrl = less_than_1500_mhz ? 0x3c : 0x03;
+ glbl_rescode_bot_ctrl = less_than_1500_mhz ? 0x38 : 0x3c;
+ }
+ } else if ((phy->cfg->quirks & DSI_PHY_7NM_QUIRK_V5_2)) {
if (phy->cphy_mode) {
vreg_ctrl_0 = 0x45;
vreg_ctrl_1 = 0x41;
@@ -1010,6 +1052,7 @@ static int dsi_7nm_phy_enable(struct msm_dsi_phy *phy,
/* program CMN_CTRL_4 for minor_ver 2 chipsets*/
if ((phy->cfg->quirks & DSI_PHY_7NM_QUIRK_V5_2) ||
+ (phy->cfg->quirks & DSI_PHY_7NM_QUIRK_V7_0) ||
(readl(base + REG_DSI_7nm_PHY_CMN_REVISION_ID0) & (0xf0)) == 0x20)
writel(0x04, base + REG_DSI_7nm_PHY_CMN_CTRL_4);
@@ -1124,7 +1167,8 @@ static void dsi_7nm_phy_disable(struct msm_dsi_phy *phy)
/* Turn off REFGEN Vote */
if ((phy->cfg->quirks & DSI_PHY_7NM_QUIRK_V4_3) ||
- (phy->cfg->quirks & DSI_PHY_7NM_QUIRK_V5_2)) {
+ (phy->cfg->quirks & DSI_PHY_7NM_QUIRK_V5_2) ||
+ (phy->cfg->quirks & DSI_PHY_7NM_QUIRK_V7_0)) {
writel(0x0, base + REG_DSI_7nm_PHY_CMN_GLBL_DIGTOP_SPARE10);
wmb();
/* Delay to ensure HW removes vote before PHY shut down */
@@ -1341,3 +1385,26 @@ const struct msm_dsi_phy_cfg dsi_phy_4nm_8650_cfgs = {
.num_dsi_phy = 2,
.quirks = DSI_PHY_7NM_QUIRK_V5_2,
};
+
+const struct msm_dsi_phy_cfg dsi_phy_3nm_8750_cfgs = {
+ .has_phy_lane = true,
+ .regulator_data = dsi_phy_7nm_98000uA_regulators,
+ .num_regulators = ARRAY_SIZE(dsi_phy_7nm_98000uA_regulators),
+ .ops = {
+ .enable = dsi_7nm_phy_enable,
+ .disable = dsi_7nm_phy_disable,
+ .pll_init = dsi_pll_7nm_init,
+ .save_pll_state = dsi_7nm_pll_save_state,
+ .restore_pll_state = dsi_7nm_pll_restore_state,
+ .set_continuous_clock = dsi_7nm_set_continuous_clock,
+ },
+ .min_pll_rate = 600000000UL,
+#ifdef CONFIG_64BIT
+ .max_pll_rate = 5000000000UL,
+#else
+ .max_pll_rate = ULONG_MAX,
+#endif
+ .io_start = { 0xae95000, 0xae97000 },
+ .num_dsi_phy = 2,
+ .quirks = DSI_PHY_7NM_QUIRK_V7_0,
+};
diff --git a/drivers/gpu/drm/msm/registers/display/dsi_phy_7nm.xml b/drivers/gpu/drm/msm/registers/display/dsi_phy_7nm.xml
index d2c8c46bb04159da6e539bfe80a4b5dc9ffdf367..d62411961f5673e0a7a37b90cfc99962de83659e 100644
--- a/drivers/gpu/drm/msm/registers/display/dsi_phy_7nm.xml
+++ b/drivers/gpu/drm/msm/registers/display/dsi_phy_7nm.xml
@@ -26,6 +26,7 @@ xsi:schemaLocation="https://gitlab.freedesktop.org/freedreno/ rules-fd.xsd">
<reg32 offset="0x00028" name="CTRL_1"/>
<reg32 offset="0x0002c" name="CTRL_2"/>
<reg32 offset="0x00030" name="CTRL_3"/>
+ <reg32 offset="0x001b0" name="CTRL_5"/>
<reg32 offset="0x00034" name="LANE_CFG0"/>
<reg32 offset="0x00038" name="LANE_CFG1"/>
<reg32 offset="0x0003c" name="PLL_CNTRL"/>
@@ -191,11 +192,24 @@ xsi:schemaLocation="https://gitlab.freedesktop.org/freedreno/ rules-fd.xsd">
<reg32 offset="0x01b0" name="COMMON_STATUS_ONE"/>
<reg32 offset="0x01b4" name="COMMON_STATUS_TWO"/>
<reg32 offset="0x01b8" name="BAND_SEL_CAL"/>
+ <!--
+ Starting from SM8750, offset moved from 0x01bc to 0x01cc, however
+ we keep only one register map. That's not a problem, so far,
+ because this register is not used. The register map should be split
+ once it is going to be used. Comment out the code to prevent
+ any misuse due to the change in the offset.
<reg32 offset="0x01bc" name="ICODE_ACCUM_STATUS_LOW"/>
+ <reg32 offset="0x01cc" name="ICODE_ACCUM_STATUS_LOW"/>
+ -->
<reg32 offset="0x01c0" name="ICODE_ACCUM_STATUS_HIGH"/>
<reg32 offset="0x01c4" name="FD_OUT_LOW"/>
<reg32 offset="0x01c8" name="FD_OUT_HIGH"/>
+ <!--
+ Starting from SM8750, offset moved from 0x01cc to 0x01bc, however
+ we keep only one register map. See above comment.
<reg32 offset="0x01cc" name="ALOG_OBSV_BUS_STATUS_1"/>
+ <reg32 offset="0x01bc" name="ALOG_OBSV_BUS_STATUS_1"/>
+ -->
<reg32 offset="0x01d0" name="PLL_MISC_CONFIG"/>
<reg32 offset="0x01d4" name="FLL_CONFIG"/>
<reg32 offset="0x01d8" name="FLL_FREQ_ACQ_TIME"/>
--
2.43.0
