Re: [PATCH v5 4/6] arm64: dts: qcom: Add UFS node

[Date Prev][Date Next][Thread Prev][Thread Next][Date Index][Thread Index]

 



On Fri Aug 30, 2024 at 7:25 PM CEST, Marcus Glocker wrote:
> On Fri, Aug 30, 2024 at 02:05:48AM +0200, Konrad Dybcio wrote:
>
>> On 17.08.2024 10:38 PM, Marcus Glocker wrote:
>> > Add the UFS Host Controller node.  This was basically copied from the
>> > arch/arm64/boot/dts/qcom/sc7180.dtsi file.
>> >
>> > Signed-off-by: Marcus Glocker <marcus@xxxxxxxxx>
>> > Acked-by: Krzysztof Kozlowski <krzysztof.kozlowski@xxxxxxxxxx>
>> > ---
>> >  arch/arm64/boot/dts/qcom/x1e80100.dtsi | 72 ++++++++++++++++++++++++++
>> >  1 file changed, 72 insertions(+)
>> >
>> > diff --git a/arch/arm64/boot/dts/qcom/x1e80100.dtsi 
>> > b/arch/arm64/boot/dts/qcom/x1e80100.dtsi
>> > index 7bca5fcd7d52..9f01b3ff3737 100644
>> > --- a/arch/arm64/boot/dts/qcom/x1e80100.dtsi
>> > +++ b/arch/arm64/boot/dts/qcom/x1e80100.dtsi
>> > @@ -2878,6 +2878,78 @@ mmss_noc: interconnect@1780000 {
>> >  			#interconnect-cells = <2>;
>> >  		};
>> >
>> > +		ufs_mem_hc: ufs@1d84000 {
>> > +			compatible = "qcom,x1e80100-ufshc", "qcom,ufshc",
>> > +				     "jedec,ufs-2.0";
>> > +			reg = <0 0x01d84000 0 0x3000>;
>> > +			interrupts = <GIC_SPI 265 IRQ_TYPE_LEVEL_HIGH>;
>> > +			phys = <&ufs_mem_phy>;
>> > +			phy-names = "ufsphy";
>> > +			lanes-per-direction = <1>;
>> > +			#reset-cells = <1>;
>> > +			resets = <&gcc GCC_UFS_PHY_BCR>;
>> > +			reset-names = "rst";
>> > +
>> > +			power-domains = <&gcc GCC_UFS_PHY_GDSC>;
>> > +
>> > +			iommus = <&apps_smmu 0xa0 0x0>;
>> 
>> Looks like this should be 0x1a0 maybe
>> > +
>> > +			clock-names = "core_clk",
>> > +				      "bus_aggr_clk",
>> > +				      "iface_clk",
>> > +				      "core_clk_unipro",
>> > +				      "ref_clk",
>> > +				      "tx_lane0_sync_clk",
>> > +				      "rx_lane0_sync_clk";
>> > +			clocks = <&gcc GCC_UFS_PHY_AXI_CLK>,
>> > +				 <&gcc GCC_AGGRE_UFS_PHY_AXI_CLK>,
>> > +				 <&gcc GCC_UFS_PHY_AHB_CLK>,
>> > +				 <&gcc GCC_UFS_PHY_UNIPRO_CORE_CLK>,
>> > +				 <&rpmhcc RPMH_CXO_CLK>,
>> > +				 <&gcc GCC_UFS_PHY_TX_SYMBOL_0_CLK>,
>> > +				 <&gcc GCC_UFS_PHY_RX_SYMBOL_0_CLK>;
>> 
>> You also want
>> 
>> <&gcc GCC_UFS_PHY_RX_SYMBOL_1_CLK>
>> 
>> > +			freq-table-hz = <50000000 200000000>,
>> 25000000 300000000
>> 
>> > +					<0 0>,
>> > +					<0 0>,
>> > +					<37500000 150000000>,
>> 75000000 300000000
>> 
>> > +					<0 0>,
>> > +					<0 0>,
>> > +					<0 0>;
>> > +
>> > +			interconnects = <&aggre1_noc MASTER_UFS_MEM QCOM_ICC_TAG_ALWAYS
>> > +					 &mc_virt SLAVE_EBI1 QCOM_ICC_TAG_ALWAYS>,
>> > +					<&gem_noc MASTER_APPSS_PROC QCOM_ICC_TAG_ALWAYS
>> > +					 &config_noc SLAVE_UFS_MEM_CFG QCOM_ICC_TAG_ALWAYS>;
>> > +			interconnect-names = "ufs-ddr", "cpu-ufs";
>> > +
>> > +			qcom,ice = <&ice>;
>> > +
>> > +			status = "disabled";
>> > +		};
>> > +
>> > +		ufs_mem_phy: phy@1d87000 {
>> > +			compatible = "qcom,x1e80100-qmp-ufs-phy";
>> > +			reg = <0 0x01d87000 0 0x1000>;
>> 
>> most definitely should be 0x01d80000 with a size of 0x2000
>> 
>> > +			clocks = <&rpmhcc RPMH_CXO_CLK>,
>> > +				 <&gcc GCC_UFS_PHY_PHY_AUX_CLK>,
>> > +				 <&tcsr TCSR_UFS_PHY_CLKREF_EN>;
>> > +			clock-names = "ref",
>> > +				      "ref_aux",
>> > +				      "qref";
>> > +			power-domains = <&gcc GCC_UFS_PHY_GDSC>;
>> > +			resets = <&ufs_mem_hc 0>;
>> > +			reset-names = "ufsphy";
>> > +			#phy-cells = <0>;
>> > +			status = "disabled";
>> > +		};
>> > +
>> > +		ice: crypto@1d90000 {
>> > +			compatible = "qcom,x1e80100-inline-crypto-engine",
>> > +				     "qcom,inline-crypto-engine";
>> > +			reg = <0 0x01d90000 0 0x8000>;
>> 
>> 0x1d88000
>> 
>> 
>> All this combined means you probably wrote your init sequence into some
>> free(?) register space and the one left over from the bootloader was
>> good enough :P
>> 
>> Konrad
>
> I have not done anything special in our sub-system to boot this DTB.
> Changing the values as suggested by you also doesn't make any difference
> to me.
>
> Anyway, I think I'll give up at this point, since this process is
> getting too time consuming for me.  We'll go ahead with out downstream
> patches, which works for us so far.

Hi Marcus,

I came across this and I'd be interested in picking up the patches for testing.
Is there any guide or documentation available that I could follow to boot Linux
on this machine using this patchset? Also, could you share where I might be able
to find those downstream patches?

Thanks,
Daniel

>
> Cheers,
> Marcus






[Index of Archives]     [Linux ARM Kernel]     [Linux ARM]     [Linux Omap]     [Fedora ARM]     [Linux for Sparc]     [IETF Annouce]     [Security]     [Bugtraq]     [Linux MIPS]     [ECOS]     [Asterisk Internet PBX]     [Linux API]

  Powered by Linux