On Fri, Oct 04, 2024 at 04:57:38PM +0300, Abel Vesa wrote:
> +static int ps8830_enable_vregs(struct ps8830_retimer *retimer)
> +{
> + return 0;
> +
> +err_vddat_disable:
> + regulator_disable(retimer->vddat_supply);
> +
Nit: I'd drop the empty lines between the errors cases here.
> +err_vddar_disable:
> + regulator_disable(retimer->vddar_supply);
> +
> +err_vdd_disable:
> + regulator_disable(retimer->vdd_supply);
> +
> +err_vdd33_cap_disable:
> + regulator_disable(retimer->vdd33_cap_supply);
> +
> +err_vdd33_disable:
> + regulator_disable(retimer->vdd33_supply);
> +
> + return ret;
> +}
> +static int ps8830_retimer_probe(struct i2c_client *client)
> +{
> + struct device *dev = &client->dev;
> + struct typec_switch_desc sw_desc = { };
> + struct typec_retimer_desc rtmr_desc = { };
> + struct ps8830_retimer *retimer;
> + int ret;
> +
> + retimer = devm_kzalloc(dev, sizeof(*retimer), GFP_KERNEL);
> + if (!retimer)
> + return -ENOMEM;
> +
> + retimer->client = client;
> +
> + mutex_init(&retimer->lock);
> +
> + retimer->regmap = devm_regmap_init_i2c(client, &ps8830_retimer_regmap);
> + if (IS_ERR(retimer->regmap)) {
> + dev_err(dev, "failed to allocate register map\n");
Please make sure to log the errno as well here and below.
> + return PTR_ERR(retimer->regmap);
> + }
> +
> + ret = ps8830_get_vregs(retimer);
> + if (ret)
> + return ret;
> +
> + retimer->xo_clk = devm_clk_get(dev, "xo");
> + if (IS_ERR(retimer->xo_clk))
> + return dev_err_probe(dev, PTR_ERR(retimer->xo_clk),
> + "failed to get xo clock\n");
> +
> + retimer->reset_gpio = devm_gpiod_get(dev, "reset", GPIOD_OUT_HIGH);
The reset line is active low and should be described as such in DT. So
here you want to request it as logically low if you want to deassert
reset.
Is there now timing requirements on when you deassert reset after
enabling the supplies?
> + if (IS_ERR(retimer->reset_gpio))
> + return dev_err_probe(dev, PTR_ERR(retimer->reset_gpio),
> + "failed to get reset gpio\n");
> +
> + retimer->typec_switch = fwnode_typec_switch_get(dev->fwnode);
> + if (IS_ERR(retimer->typec_switch)) {
> + dev_err(dev, "failed to acquire orientation-switch\n");
I saw the driver fail here once, but not sure what the errno was since
it was not printed. Presumably it was a probe deferral and then this
should be a dev_err_probe() as well:
ps8830_retimer 2-0008: failed to acquire orientation-switch
> + return PTR_ERR(retimer->typec_switch);
> + }
> +
> + retimer->typec_mux = fwnode_typec_mux_get(dev->fwnode);
> + if (IS_ERR(retimer->typec_mux)) {
> + dev_err(dev, "failed to acquire mode-mux\n");
Similar here perhaps?
> + goto err_switch_put;
> + }
> +
> + sw_desc.drvdata = retimer;
> + sw_desc.fwnode = dev_fwnode(dev);
> + sw_desc.set = ps8830_sw_set;
> +
> + ret = drm_aux_bridge_register(dev);
> + if (ret)
> + goto err_mux_put;
> +
> + retimer->sw = typec_switch_register(dev, &sw_desc);
> + if (IS_ERR(retimer->sw)) {
> + dev_err(dev, "failed to register typec switch\n");
> + goto err_aux_bridge_unregister;
> + }
> +
> + rtmr_desc.drvdata = retimer;
> + rtmr_desc.fwnode = dev_fwnode(dev);
> + rtmr_desc.set = ps8830_retimer_set;
> +
> + retimer->retimer = typec_retimer_register(dev, &rtmr_desc);
> + if (IS_ERR(retimer->retimer)) {
> + dev_err(dev, "failed to register typec retimer\n");
> + goto err_switch_unregister;
> + }
> +
> + ret = clk_prepare_enable(retimer->xo_clk);
> + if (ret) {
> + dev_err(dev, "failed to enable XO: %d\n", ret);
> + goto err_retimer_unregister;
> + }
Should you really enable the clock before the regulators?
> +
> + ret = ps8830_enable_vregs(retimer);
> + if (ret)
> + goto err_clk_disable;
> +
> + /* delay needed as per datasheet */
> + usleep_range(4000, 14000);
> +
> + gpiod_set_value(retimer->reset_gpio, 1);
Here you only deassert reset in case the line is incorrectly described
as active high in DT.
> + return 0;
> +
> +err_clk_disable:
> + clk_disable_unprepare(retimer->xo_clk);
> +
> +err_retimer_unregister:
> + typec_retimer_unregister(retimer->retimer);
> +
> +err_switch_unregister:
> + typec_switch_unregister(retimer->sw);
> +
> +err_aux_bridge_unregister:
> + gpiod_set_value(retimer->reset_gpio, 0);
> + clk_disable_unprepare(retimer->xo_clk);
> +
> +err_mux_put:
> + typec_mux_put(retimer->typec_mux);
> +
> +err_switch_put:
> + typec_switch_put(retimer->typec_switch);
Drop newlines before labels?
> +
> + return ret;
> +}
Johan
