[PATCH 3/3] arm64: dts: qcom: x1e80100-qcp: Add WiFi/BT pwrseq

[Date Prev][Date Next][Thread Prev][Thread Next][Date Index][Thread Index]

 



Add the WiFi/BT nodes for QCP and describe the regulators for the WCN7850
combo chip using the new power sequencing bindings. All voltages are
derived from chained fixed regulators controlled using a single GPIO.

The same setup also works for CRD (and likely most of the other X1E80100
laptops). However, unlike the QCP they use soldered or removable M.2 cards
supplied by a single 3.3V fixed regulator. The other necessary voltages are
then derived inside the M.2 card. Describing this properly requires
new bindings, so this commit only adds QCP for now.

Signed-off-by: Stephan Gerhold <stephan.gerhold@xxxxxxxxxx>
---
 arch/arm64/boot/dts/qcom/x1e80100-qcp.dts | 144 ++++++++++++++++++++++++++++++
 1 file changed, 144 insertions(+)

diff --git a/arch/arm64/boot/dts/qcom/x1e80100-qcp.dts b/arch/arm64/boot/dts/qcom/x1e80100-qcp.dts
index 1c3a6a7b3ed6..9977c2a505b9 100644
--- a/arch/arm64/boot/dts/qcom/x1e80100-qcp.dts
+++ b/arch/arm64/boot/dts/qcom/x1e80100-qcp.dts
@@ -17,6 +17,7 @@ / {
 
 	aliases {
 		serial0 = &uart21;
+		serial1 = &uart14;
 	};
 
 	wcd938x: audio-codec {
@@ -254,6 +255,101 @@ vreg_nvme: regulator-nvme {
 		pinctrl-names = "default";
 		pinctrl-0 = <&nvme_reg_en>;
 	};
+
+	vreg_wcn_3p3: regulator-wcn-3p3 {
+		compatible = "regulator-fixed";
+
+		regulator-name = "VREG_WCN_3P3";
+		regulator-min-microvolt = <3300000>;
+		regulator-max-microvolt = <3300000>;
+
+		gpio = <&tlmm 214 GPIO_ACTIVE_HIGH>;
+		enable-active-high;
+
+		pinctrl-0 = <&wcn_sw_en>;
+		pinctrl-names = "default";
+
+		regulator-boot-on;
+	};
+
+	vreg_wcn_0p95: regulator-wcn-0p95 {
+		compatible = "regulator-fixed";
+
+		regulator-name = "VREG_WCN_0P95";
+		regulator-min-microvolt = <950000>;
+		regulator-max-microvolt = <950000>;
+
+		vin-supply = <&vreg_wcn_3p3>;
+	};
+
+	vreg_wcn_1p9: regulator-wcn-1p9 {
+		compatible = "regulator-fixed";
+
+		regulator-name = "VREG_WCN_1P9";
+		regulator-min-microvolt = <1900000>;
+		regulator-max-microvolt = <1900000>;
+
+		vin-supply = <&vreg_wcn_3p3>;
+	};
+
+	wcn7850-pmu {
+		compatible = "qcom,wcn7850-pmu";
+
+		vdd-supply = <&vreg_wcn_0p95>;
+		vddio-supply = <&vreg_l15b_1p8>;
+		vddaon-supply = <&vreg_wcn_0p95>;
+		vdddig-supply = <&vreg_wcn_0p95>;
+		vddrfa1p2-supply = <&vreg_wcn_1p9>;
+		vddrfa1p8-supply = <&vreg_wcn_1p9>;
+
+		wlan-enable-gpios = <&tlmm 117 GPIO_ACTIVE_HIGH>;
+		bt-enable-gpios = <&tlmm 116 GPIO_ACTIVE_HIGH>;
+
+		pinctrl-0 = <&wcn_wlan_bt_en>;
+		pinctrl-names = "default";
+
+		regulators {
+			vreg_pmu_rfa_cmn: ldo0 {
+				regulator-name = "vreg_pmu_rfa_cmn";
+			};
+
+			vreg_pmu_aon_0p59: ldo1 {
+				regulator-name = "vreg_pmu_aon_0p59";
+			};
+
+			vreg_pmu_wlcx_0p8: ldo2 {
+				regulator-name = "vreg_pmu_wlcx_0p8";
+			};
+
+			vreg_pmu_wlmx_0p85: ldo3 {
+				regulator-name = "vreg_pmu_wlmx_0p85";
+			};
+
+			vreg_pmu_btcmx_0p85: ldo4 {
+				regulator-name = "vreg_pmu_btcmx_0p85";
+			};
+
+			vreg_pmu_rfa_0p8: ldo5 {
+				regulator-name = "vreg_pmu_rfa_0p8";
+			};
+
+			vreg_pmu_rfa_1p2: ldo6 {
+				regulator-name = "vreg_pmu_rfa_1p2";
+			};
+
+			vreg_pmu_rfa_1p8: ldo7 {
+				regulator-name = "vreg_pmu_rfa_1p8";
+			};
+
+			vreg_pmu_pcie_0p9: ldo8 {
+				regulator-name = "vreg_pmu_pcie_0p9";
+			};
+
+			vreg_pmu_pcie_1p8: ldo9 {
+				regulator-name = "vreg_pmu_pcie_1p8";
+			};
+		};
+	};
 };
 
 &apps_rsc {
@@ -684,6 +780,23 @@ &pcie4_phy {
 	status = "okay";
 };
 
+&pcie4_port0 {
+	wifi@0 {
+		compatible = "pci17cb,1107";
+		reg = <0x10000 0x0 0x0 0x0 0x0>;
+
+		vddaon-supply = <&vreg_pmu_aon_0p59>;
+		vddwlcx-supply = <&vreg_pmu_wlcx_0p8>;
+		vddwlmx-supply = <&vreg_pmu_wlmx_0p85>;
+		vddrfacmn-supply = <&vreg_pmu_rfa_cmn>;
+		vddrfa0p8-supply = <&vreg_pmu_rfa_0p8>;
+		vddrfa1p2-supply = <&vreg_pmu_rfa_1p2>;
+		vddrfa1p8-supply = <&vreg_pmu_rfa_1p8>;
+		vddpcie0p9-supply = <&vreg_pmu_pcie_0p9>;
+		vddpcie1p8-supply = <&vreg_pmu_pcie_1p8>;
+	};
+};
+
 &pcie6a {
 	perst-gpios = <&tlmm 152 GPIO_ACTIVE_LOW>;
 	wake-gpios = <&tlmm 154 GPIO_ACTIVE_LOW>;
@@ -877,6 +990,37 @@ wcd_default: wcd-reset-n-active-state {
 		bias-disable;
 		output-low;
 	};
+
+	wcn_wlan_bt_en: wcn-wlan-bt-en-state {
+		pins = "gpio116", "gpio117";
+		function = "gpio";
+		drive-strength = <2>;
+		bias-disable;
+	};
+
+	wcn_sw_en: wcn-sw-en-state {
+		pins = "gpio214";
+		function = "gpio";
+		drive-strength = <2>;
+		bias-disable;
+	};
+};
+
+&uart14 {
+	status = "okay";
+
+	bluetooth {
+		compatible = "qcom,wcn7850-bt";
+		max-speed = <3200000>;
+
+		vddaon-supply = <&vreg_pmu_aon_0p59>;
+		vddwlcx-supply = <&vreg_pmu_wlcx_0p8>;
+		vddwlmx-supply = <&vreg_pmu_wlmx_0p85>;
+		vddrfacmn-supply = <&vreg_pmu_rfa_cmn>;
+		vddrfa0p8-supply = <&vreg_pmu_rfa_0p8>;
+		vddrfa1p2-supply = <&vreg_pmu_rfa_1p2>;
+		vddrfa1p8-supply = <&vreg_pmu_rfa_1p8>;
+	};
 };
 
 &uart21 {

-- 
2.46.0





[Index of Archives]     [Linux ARM Kernel]     [Linux ARM]     [Linux Omap]     [Fedora ARM]     [Linux for Sparc]     [IETF Annouce]     [Security]     [Bugtraq]     [Linux MIPS]     [ECOS]     [Asterisk Internet PBX]     [Linux API]

  Powered by Linux