Re: [PATCH v2 3/8] arm64: dts: qcom: qcs6490-rb3gen2: Add node for qps615

[Date Prev][Date Next][Thread Prev][Thread Next][Date Index][Thread Index]

 





On 9/9/2024 4:59 PM, Caleb Connolly wrote:
Hi Krishna,

On 03/08/2024 05:22, Krishna chaitanya chundru wrote:
Add QPS615 PCIe switch node which has 3 downstream ports and in one
downstream port two embedded ethernet devices are present.

Power to the QPS615 is supplied through two LDO regulators, controlled
by two GPIOs, these are added as fixed regulators.

Add i2c device node which is used to configure the switch.

Signed-off-by: Krishna chaitanya chundru <quic_krichai@xxxxxxxxxxx>
---
  arch/arm64/boot/dts/qcom/qcs6490-rb3gen2.dts | 121 +++++++++++++++++++++++++++
  arch/arm64/boot/dts/qcom/sc7280.dtsi         |   2 +-
  2 files changed, 122 insertions(+), 1 deletion(-)

diff --git a/arch/arm64/boot/dts/qcom/qcs6490-rb3gen2.dts b/arch/arm64/boot/dts/qcom/qcs6490-rb3gen2.dts
index 0d45662b8028..59d209768636 100644
--- a/arch/arm64/boot/dts/qcom/qcs6490-rb3gen2.dts
+++ b/arch/arm64/boot/dts/qcom/qcs6490-rb3gen2.dts
@@ -202,6 +202,30 @@ vph_pwr: vph-pwr-regulator {
  		regulator-min-microvolt = <3700000>;
  		regulator-max-microvolt = <3700000>;
  	};
+
+	vdd_ntn_0p9: regulator-vdd-ntn-0p9 {
+		compatible = "regulator-fixed";
+		regulator-name = "VDD_NTN_0P9";
+		gpio = <&pm8350c_gpios 2 GPIO_ACTIVE_HIGH>;
+		regulator-min-microvolt = <899400>;
+		regulator-max-microvolt = <899400>;
+		enable-active-high;
+		pinctrl-0 = <&ntn_0p9_en>;
+		pinctrl-names = "default";
+		regulator-enable-ramp-delay = <4300>;
+	};
+
+	vdd_ntn_1p8: regulator-vdd-ntn-1p8 {
+		compatible = "regulator-fixed";
+		regulator-name = "VDD_NTN_1P8";
+		gpio = <&pm8350c_gpios 3 GPIO_ACTIVE_HIGH>;
+		regulator-min-microvolt = <1800000>;
+		regulator-max-microvolt = <1800000>;
+		enable-active-high;
+		pinctrl-0 = <&ntn_1p8_en>;
+		pinctrl-names = "default";
+		regulator-enable-ramp-delay = <10000>;
+	};
  };
&apps_rsc {
@@ -595,6 +619,12 @@ lt9611_out: endpoint {
  			};
  		};
  	};
+
+	qps615_switch: pcie-switch@77 {
+		compatible = "qcom,qps615";
+		reg = <0x77>;
+		status = "okay";
+	};
  };
&i2c1 {
@@ -688,6 +718,75 @@ &pmk8350_rtc {
  	status = "okay";
  };
+&pcie1 {
+	status = "okay";
+};

Isn't it also necessary to configure the phy as well? It's also default
disabled and has two regulators.

There is one more patch series which does this.

https://lore.kernel.org/linux-arm-msm/20240207-enable_pcie-v1-1-b684afa6371c@xxxxxxxxxxx/T/

sorry for this I should have included this in cover letter.

I will squash those changes to this series or will update the cover
letter.
- Krishna Chaitanya.

Kind regards >> +
+&pcieport {
+	pcie@0,0 {
+		compatible = "pci1179,0623";
+		reg = <0x10000 0x0 0x0 0x0 0x0>;
+		#address-cells = <3>;
+		#size-cells = <2>;
+
+		device_type = "pci";
+		ranges;
+
+		vddc-supply = <&vdd_ntn_0p9>;
+		vdd18-supply = <&vdd_ntn_1p8>;
+		vdd09-supply = <&vdd_ntn_0p9>;
+		vddio1-supply = <&vdd_ntn_1p8>;
+		vddio2-supply = <&vdd_ntn_1p8>;
+		vddio18-supply = <&vdd_ntn_1p8>;
+
+		qcom,qps615-controller = <&qps615_switch>;
+
+		reset-gpios = <&pm8350c_gpios 1 GPIO_ACTIVE_LOW>;
+
+		pcie@1,0 {
+			reg = <0x20800 0x0 0x0 0x0 0x0>;
+			#address-cells = <3>;
+			#size-cells = <2>;
+
+			device_type = "pci";
+			ranges;
+		};
+
+		pcie@2,0 {
+			reg = <0x21000 0x0 0x0 0x0 0x0>;
+			#address-cells = <3>;
+			#size-cells = <2>;
+
+			device_type = "pci";
+			ranges;
+		};
+
+		pcie@3,0 {
+			reg = <0x21800 0x0 0x0 0x0 0x0>;
+			#address-cells = <3>;
+			#size-cells = <2>;
+			device_type = "pci";
+			ranges;
+
+			pcie@0,0 {
+				reg = <0x50000 0x0 0x0 0x0 0x0>;
+				#address-cells = <3>;
+				#size-cells = <2>;
+				device_type = "pci";
+				ranges;
+			};
+
+			pcie@0,1 {
+				reg = <0x50100 0x0 0x0 0x0 0x0>;
+				#address-cells = <3>;
+				#size-cells = <2>;
+				device_type = "pci";
+				ranges;
+			};
+		};
+	};
+};
+
  &qupv3_id_0 {
  	status = "okay";
  };
@@ -812,6 +911,28 @@ lt9611_rst_pin: lt9611-rst-state {
  	};
  };
+&pm8350c_gpios {
+	ntn_0p9_en: ntn-0p9-en-state {
+		pins = "gpio2";
+		function = "normal";
+
+		bias-disable;
+		input-disable;
+		output-enable;
+		power-source = <0>;
+	};
+
+	ntn_1p8_en: ntn-1p8-en-state {
+		pins = "gpio3";
+		function = "normal";
+
+		bias-disable;
+		input-disable;
+		output-enable;
+		power-source = <0>;
+	};
+};
+
  &tlmm {
  	lt9611_irq_pin: lt9611-irq-state {
  		pins = "gpio24";
diff --git a/arch/arm64/boot/dts/qcom/sc7280.dtsi b/arch/arm64/boot/dts/qcom/sc7280.dtsi
index 3d8410683402..3840f056b7f2 100644
--- a/arch/arm64/boot/dts/qcom/sc7280.dtsi
+++ b/arch/arm64/boot/dts/qcom/sc7280.dtsi
@@ -2279,7 +2279,7 @@ pcie1: pcie@1c08000 {
status = "disabled"; - pcie@0 {
+			pcieport: pcie@0 {
  				device_type = "pci";
  				reg = <0x0 0x0 0x0 0x0 0x0>;
  				bus-range = <0x01 0xff>;






[Index of Archives]     [Linux ARM Kernel]     [Linux ARM]     [Linux Omap]     [Fedora ARM]     [Linux for Sparc]     [IETF Annouce]     [Security]     [Bugtraq]     [Linux MIPS]     [ECOS]     [Asterisk Internet PBX]     [Linux API]

  Powered by Linux