The actual PHY used by MDSS DP2 is the USB SS2 QMP one. So switch to it
instead. This is needed to get external DP support on boards like CRD
where the 3rd Type-C USB port (right-hand side) is connected to DP2.
Fixes: 1940c25eaa63 ("arm64: dts: qcom: x1e80100: Add display nodes")
Signed-off-by: Abel Vesa <abel.vesa@xxxxxxxxxx>
---
arch/arm64/boot/dts/qcom/x1e80100.dtsi | 10 +++++-----
1 file changed, 5 insertions(+), 5 deletions(-)
diff --git a/arch/arm64/boot/dts/qcom/x1e80100.dtsi b/arch/arm64/boot/dts/qcom/x1e80100.dtsi
index 6abff8258674..197f9028de31 100644
--- a/arch/arm64/boot/dts/qcom/x1e80100.dtsi
+++ b/arch/arm64/boot/dts/qcom/x1e80100.dtsi
@@ -4715,14 +4715,14 @@ mdss_dp2: displayport-controller@ae9a000 {
assigned-clocks = <&dispcc DISP_CC_MDSS_DPTX2_LINK_CLK_SRC>,
<&dispcc DISP_CC_MDSS_DPTX2_PIXEL0_CLK_SRC>;
- assigned-clock-parents = <&mdss_dp2_phy 0>,
- <&mdss_dp2_phy 1>;
+ assigned-clock-parents = <&usb_1_ss2_qmpphy QMP_USB43DP_DP_LINK_CLK>,
+ <&usb_1_ss2_qmpphy QMP_USB43DP_DP_VCO_DIV_CLK>;
operating-points-v2 = <&mdss_dp2_opp_table>;
power-domains = <&rpmhpd RPMHPD_MMCX>;
- phys = <&mdss_dp2_phy>;
+ phys = <&usb_1_ss2_qmpphy QMP_USB43DP_DP_PHY>;
phy-names = "dp";
#sound-dai-cells = <0>;
@@ -4910,8 +4910,8 @@ dispcc: clock-controller@af00000 {
<&usb_1_ss0_qmpphy QMP_USB43DP_DP_VCO_DIV_CLK>,
<&usb_1_ss1_qmpphy QMP_USB43DP_DP_LINK_CLK>, /* dp1 */
<&usb_1_ss1_qmpphy QMP_USB43DP_DP_VCO_DIV_CLK>,
- <&mdss_dp2_phy 0>, /* dp2 */
- <&mdss_dp2_phy 1>,
+ <&usb_1_ss2_qmpphy QMP_USB43DP_DP_LINK_CLK>, /* dp2 */
+ <&usb_1_ss2_qmpphy QMP_USB43DP_DP_VCO_DIV_CLK>,
<&mdss_dp3_phy 0>, /* dp3 */
<&mdss_dp3_phy 1>;
power-domains = <&rpmhpd RPMHPD_MMCX>;
---
base-commit: b18bbfc14a38b5234e09c2adcf713e38063a7e6e
change-id: 20240829-x1e80100-dts-dp2-use-qmpphy-ss2-cbec8c3d8a2a
Best regards,
--
Abel Vesa <abel.vesa@xxxxxxxxxx>
