Add support for TEMP_ALARM GEN2 PMIC peripherals with digital major
revision 2. This revision utilizes individual temp DAC registers
to set the threshold temperature for over-temperature stages 1,
2, and 3 instead of a single register to specify a set of
thresholds.
Co-developed-by: David Collins <quic_collinsd@xxxxxxxxxxx>
Signed-off-by: David Collins <quic_collinsd@xxxxxxxxxxx>
Signed-off-by: Anjelique Melendez <quic_amelende@xxxxxxxxxxx>
---
drivers/thermal/qcom/qcom-spmi-temp-alarm.c | 195 ++++++++++++++++++--
1 file changed, 184 insertions(+), 11 deletions(-)
diff --git a/drivers/thermal/qcom/qcom-spmi-temp-alarm.c b/drivers/thermal/qcom/qcom-spmi-temp-alarm.c
index de4a2d99f0d5..1f56acd8f637 100644
--- a/drivers/thermal/qcom/qcom-spmi-temp-alarm.c
+++ b/drivers/thermal/qcom/qcom-spmi-temp-alarm.c
@@ -24,6 +24,10 @@
#define QPNP_TM_REG_STATUS 0x08
#define QPNP_TM_REG_SHUTDOWN_CTRL1 0x40
#define QPNP_TM_REG_ALARM_CTRL 0x46
+/* TEMP_DAC_* registers are only present for TEMP_GEN2 v2.0 */
+#define QPNP_TM_REG_TEMP_DAC_STG1 0x47
+#define QPNP_TM_REG_TEMP_DAC_STG2 0x48
+#define QPNP_TM_REG_TEMP_DAC_STG3 0x49
#define QPNP_TM_TYPE 0x09
#define QPNP_TM_SUBTYPE_GEN1 0x08
@@ -65,13 +69,42 @@ static const long temp_map_gen2_v1[THRESH_COUNT][STAGE_COUNT] = {
#define TEMP_STAGE_HYSTERESIS 2000
+/*
+ * For TEMP_GEN2 v2.0, TEMP_DAC_STG1/2/3 registers are used to set the threshold
+ * for each stage independently.
+ * TEMP_DAC_STG* = 0 --> 80 C
+ * Each 8 step increase in TEMP_DAC_STG* value corresponds to 5 C (5000 mC).
+ */
+#define TEMP_DAC_MIN 80000
+#define TEMP_DAC_SCALE_NUM 8
+#define TEMP_DAC_SCALE_DEN 5000
+
+#define TEMP_DAC_TEMP_TO_REG(temp) \
+ (((temp) - TEMP_DAC_MIN) * TEMP_DAC_SCALE_NUM / TEMP_DAC_SCALE_DEN)
+#define TEMP_DAC_REG_TO_TEMP(reg) \
+ (TEMP_DAC_MIN + (reg) * TEMP_DAC_SCALE_DEN / TEMP_DAC_SCALE_NUM)
+
+static const long temp_dac_max[STAGE_COUNT] = {
+ 119375, 159375, 159375
+};
+
/* Temperature in Milli Celsius reported during stage 0 if no ADC is present */
#define DEFAULT_TEMP 37000
+struct qpnp_tm_chip;
+
+struct spmi_temp_alarm_data {
+ const struct thermal_zone_device_ops *ops;
+ bool has_temp_dac;
+ int (*setup)(struct qpnp_tm_chip *chip);
+ int (*update_trip_temps)(struct qpnp_tm_chip *chip);
+};
+
struct qpnp_tm_chip {
struct regmap *map;
struct device *dev;
struct thermal_zone_device *tz_dev;
+ const struct spmi_temp_alarm_data *data;
unsigned int subtype;
unsigned int dig_revision;
long temp;
@@ -85,6 +118,8 @@ struct qpnp_tm_chip {
struct iio_channel *adc;
const long (*temp_map)[THRESH_COUNT][STAGE_COUNT];
+
+ long temp_dac_map[STAGE_COUNT];
};
/* This array maps from GEN2 alarm state to GEN1 alarm stage */
@@ -118,6 +153,13 @@ static int qpnp_tm_write(struct qpnp_tm_chip *chip, u16 addr, u8 data)
*/
static long qpnp_tm_decode_temp(struct qpnp_tm_chip *chip, unsigned int stage)
{
+ if (chip->data->has_temp_dac) {
+ if (stage == 0 || stage > STAGE_COUNT)
+ return 0;
+
+ return chip->temp_dac_map[stage - 1];
+ }
+
if (!chip->temp_map || chip->thresh >= THRESH_COUNT || stage == 0 ||
stage > STAGE_COUNT)
return 0;
@@ -219,6 +261,34 @@ static int qpnp_tm_get_temp(struct thermal_zone_device *tz, int *temp)
return 0;
}
+static int qpnp_tm_gen2_rev2_set_temp_thresh(struct qpnp_tm_chip *chip, int trip,
+ int temp)
+{
+ int ret, temp_cfg;
+ u8 reg;
+
+ if (trip < 0 || trip >= STAGE_COUNT) {
+ dev_err(chip->dev, "invalid TEMP_DAC trip = %d\n", trip);
+ return -EINVAL;
+ } else if (temp < TEMP_DAC_MIN || temp > temp_dac_max[trip]) {
+ dev_err(chip->dev, "invalid TEMP_DAC temp = %d\n", temp);
+ return -EINVAL;
+ }
+
+ reg = TEMP_DAC_TEMP_TO_REG(temp);
+ temp_cfg = TEMP_DAC_REG_TO_TEMP(reg);
+
+ ret = qpnp_tm_write(chip, QPNP_TM_REG_TEMP_DAC_STG1 + trip, reg);
+ if (ret < 0) {
+ dev_err(chip->dev, "TEMP_DAC_STG write failed, ret=%d\n", ret);
+ return ret;
+ }
+
+ chip->temp_dac_map[trip] = temp_cfg;
+
+ return 0;
+}
+
static int qpnp_tm_update_critical_trip_temp(struct qpnp_tm_chip *chip,
int temp)
{
@@ -286,6 +356,24 @@ static const struct thermal_zone_device_ops qpnp_tm_sensor_ops = {
.set_trip_temp = qpnp_tm_set_trip_temp,
};
+static int qpnp_tm_gen2_rev2_set_trip_temp(struct thermal_zone_device *tz,
+ int trip, int temp)
+{
+ struct qpnp_tm_chip *chip = tz->devdata;
+ int ret;
+
+ mutex_lock(&chip->lock);
+ ret = qpnp_tm_gen2_rev2_set_temp_thresh(chip, trip, temp);
+ mutex_unlock(&chip->lock);
+
+ return ret;
+}
+
+static const struct thermal_zone_device_ops qpnp_tm_gen2_rev2_sensor_ops = {
+ .get_temp = qpnp_tm_get_temp,
+ .set_trip_temp = qpnp_tm_gen2_rev2_set_trip_temp,
+};
+
static irqreturn_t qpnp_tm_isr(int irq, void *data)
{
struct qpnp_tm_chip *chip = data;
@@ -313,6 +401,71 @@ static int qpnp_tm_get_critical_trip_temp(struct qpnp_tm_chip *chip)
return THERMAL_TEMP_INVALID;
}
+/* Configure TEMP_DAC registers based on DT thermal_zone trips */
+static int qpnp_tm_gen2_rev2_update_trip_temps(struct qpnp_tm_chip *chip)
+{
+ struct thermal_trip trip = {0};
+ int ret, ntrips, i;
+
+ ntrips = thermal_zone_get_num_trips(chip->tz_dev);
+ /* Keep hardware defaults if no DT trips are defined. */
+ if (ntrips <= 0)
+ return 0;
+
+ for (i = 0; i < ntrips; i++) {
+ ret = thermal_zone_get_trip(chip->tz_dev, i, &trip);
+ if (ret < 0)
+ return ret;
+
+ ret = qpnp_tm_gen2_rev2_set_temp_thresh(chip, i, trip.temperature);
+ if (ret < 0)
+ return ret;
+ }
+
+ /* Verify that trips are strictly increasing. */
+ for (i = 1; i < STAGE_COUNT; i++) {
+ if (chip->temp_dac_map[i] <= chip->temp_dac_map[i - 1]) {
+ dev_err(chip->dev, "Threshold %d=%ld <= threshold %d=%ld\n",
+ i, chip->temp_dac_map[i], i - 1,
+ chip->temp_dac_map[i - 1]);
+ return -EINVAL;
+ }
+ }
+
+ return 0;
+}
+
+/* Read the hardware default TEMP_DAC stage threshold temperatures */
+static int qpnp_tm_gen2_rev2_init(struct qpnp_tm_chip *chip)
+{
+ int ret, i;
+ u8 reg = 0;
+
+ for (i = 0; i < STAGE_COUNT; i++) {
+ ret = qpnp_tm_read(chip, QPNP_TM_REG_TEMP_DAC_STG1 + i, ®);
+ if (ret < 0)
+ return ret;
+
+ chip->temp_dac_map[i] = TEMP_DAC_REG_TO_TEMP(reg);
+ }
+
+ return 0;
+}
+
+static const struct spmi_temp_alarm_data spmi_temp_alarm_data = {
+ .ops = &qpnp_tm_sensor_ops,
+ .has_temp_dac = false,
+ .setup = NULL,
+ .update_trip_temps = NULL,
+};
+
+static const struct spmi_temp_alarm_data spmi_temp_alarm_gen2_rev2_data = {
+ .ops = &qpnp_tm_gen2_rev2_sensor_ops,
+ .has_temp_dac = true,
+ .setup = qpnp_tm_gen2_rev2_init,
+ .update_trip_temps = qpnp_tm_gen2_rev2_update_trip_temps,
+};
+
/*
* This function initializes the internal temp value based on only the
* current thermal stage and threshold. Setup threshold control and
@@ -339,21 +492,27 @@ static int qpnp_tm_init(struct qpnp_tm_chip *chip)
goto out;
chip->stage = ret;
- stage = chip->subtype == QPNP_TM_SUBTYPE_GEN1
+ stage = (chip->subtype == QPNP_TM_SUBTYPE_GEN1)
? chip->stage : alarm_state_map[chip->stage];
if (stage)
chip->temp = qpnp_tm_decode_temp(chip, stage);
- mutex_unlock(&chip->lock);
+ if (chip->data->update_trip_temps) {
+ ret = chip->data->update_trip_temps(chip);
+ if (ret < 0)
+ goto out;
+ } else {
+ mutex_unlock(&chip->lock);
- crit_temp = qpnp_tm_get_critical_trip_temp(chip);
+ crit_temp = qpnp_tm_get_critical_trip_temp(chip);
- mutex_lock(&chip->lock);
+ mutex_lock(&chip->lock);
- ret = qpnp_tm_update_critical_trip_temp(chip, crit_temp);
- if (ret < 0)
- goto out;
+ ret = qpnp_tm_update_critical_trip_temp(chip, crit_temp);
+ if (ret < 0)
+ goto out;
+ }
/* Enable the thermal alarm PMIC module in always-on mode. */
reg = ALARM_CTRL_FORCE_ENABLE;
@@ -380,6 +539,10 @@ static int qpnp_tm_probe(struct platform_device *pdev)
if (!chip)
return -ENOMEM;
+ chip->data = of_device_get_match_data(&pdev->dev);
+ if (!chip->data)
+ return -EINVAL;
+
dev_set_drvdata(&pdev->dev, chip);
chip->dev = &pdev->dev;
@@ -455,18 +618,21 @@ static int qpnp_tm_probe(struct platform_device *pdev)
}
chip->subtype = subtype;
- if (subtype == QPNP_TM_SUBTYPE_GEN2 && dig_major >= 1)
+ if (subtype == QPNP_TM_SUBTYPE_GEN2 && dig_major == 1)
chip->temp_map = &temp_map_gen2_v1;
- else
+ else if (subtype == QPNP_TM_SUBTYPE_GEN1)
chip->temp_map = &temp_map_gen1;
+ if (chip->data->setup)
+ chip->data->setup(chip);
+
/*
* Register the sensor before initializing the hardware to be able to
* read the trip points. get_temp() returns the default temperature
* before the hardware initialization is completed.
*/
chip->tz_dev = devm_thermal_of_zone_register(
- &pdev->dev, 0, chip, &qpnp_tm_sensor_ops);
+ &pdev->dev, 0, chip, chip->data->ops);
if (IS_ERR(chip->tz_dev))
return dev_err_probe(&pdev->dev, PTR_ERR(chip->tz_dev),
"failed to register sensor\n");
@@ -488,7 +654,14 @@ static int qpnp_tm_probe(struct platform_device *pdev)
}
static const struct of_device_id qpnp_tm_match_table[] = {
- { .compatible = "qcom,spmi-temp-alarm" },
+ {
+ .compatible = "qcom,spmi-temp-alarm",
+ .data = &spmi_temp_alarm_data,
+ },
+ {
+ .compatible = "qcom,spmi-temp-alarm-gen2-rev2",
+ .data = &spmi_temp_alarm_gen2_rev2_data,
+ },
{ }
};
MODULE_DEVICE_TABLE(of, qpnp_tm_match_table);
--
2.34.1
