On 7/10/2024 5:41 PM, Bjorn Helgaas wrote:
On Wed, Jul 10, 2024 at 04:38:15PM +0530, Krishna chaitanya chundru wrote:
Add support to pass D-state change notification to Endpoint
function driver.
Blank line between paragraphs.
Ack.
Read perst value to determine if the link is in D3Cold/D3hot.
I assume this reads the state of the PERST# signal driven by the host.
Style it to match the spec usage ("PERST#") to make that connection
clearer.
Ack.
D3cold/D3hot is a device state and doesn't apply to a link. Link
states are L0, L1, L2, L3,etc. Also in cover letter.
Ack.
I don't understand the connection between PERST# state and the device
D state. D3cold is defined to mean main power is absent. Is the
endpoint firmware still running when main power is absent?
Host as part of its d3cold sequence will assert the perst. so we are
reading perst to know the link the state.
Qcom devices are drawing power from the PCIe, so even when PCIe is in
D3cold endpoint firmware can still run.
- Krishna Chaitanya.
Reviewed-by: Manivannan Sadhasivam <mani@xxxxxxxxxx>
Signed-off-by: Krishna chaitanya chundru <quic_krichai@xxxxxxxxxxx>
---
drivers/pci/controller/dwc/pcie-qcom-ep.c | 8 +++++++-
1 file changed, 7 insertions(+), 1 deletion(-)
diff --git a/drivers/pci/controller/dwc/pcie-qcom-ep.c b/drivers/pci/controller/dwc/pcie-qcom-ep.c
index 236229f66c80..817fad805c51 100644
--- a/drivers/pci/controller/dwc/pcie-qcom-ep.c
+++ b/drivers/pci/controller/dwc/pcie-qcom-ep.c
@@ -648,6 +648,7 @@ static irqreturn_t qcom_pcie_ep_global_irq_thread(int irq, void *data)
struct device *dev = pci->dev;
u32 status = readl_relaxed(pcie_ep->parf + PARF_INT_ALL_STATUS);
u32 mask = readl_relaxed(pcie_ep->parf + PARF_INT_ALL_MASK);
+ pci_power_t state;
u32 dstate, val;
writel_relaxed(status, pcie_ep->parf + PARF_INT_ALL_CLEAR);
@@ -671,11 +672,16 @@ static irqreturn_t qcom_pcie_ep_global_irq_thread(int irq, void *data)
dstate = dw_pcie_readl_dbi(pci, DBI_CON_STATUS) &
DBI_CON_STATUS_POWER_STATE_MASK;
dev_dbg(dev, "Received D%d state event\n", dstate);
- if (dstate == 3) {
+ state = dstate;
+ if (dstate == PCI_D3hot) {
val = readl_relaxed(pcie_ep->parf + PARF_PM_CTRL);
val |= PARF_PM_CTRL_REQ_EXIT_L1;
writel_relaxed(val, pcie_ep->parf + PARF_PM_CTRL);
+
+ if (gpiod_get_value(pcie_ep->reset))
+ state = PCI_D3cold;
}
+ pci_epc_dstate_notify(pci->ep.epc, state);
} else if (FIELD_GET(PARF_INT_ALL_LINK_UP, status)) {
dev_dbg(dev, "Received Linkup event. Enumeration complete!\n");
dw_pcie_ep_linkup(&pci->ep);
--
2.42.0
