The multiport USB controller in the SA8295P ADP is connected to four USB Type-A ports. VBUS for each of these ports are provided by a TPS2559QWDRCTQ1 regulator, controlled from PMIC GPIOs. Add the necessary regulators and GPIO configuration to power these. It seems reasonable that these regulators should be referenced as vbus supply of usb-a-connector nodes and controlled by e.g. dwc3, but as this is not supported in Linux today the regulators are left always-on for now. Signed-off-by: Krishna Kurapati <quic_kriskura@xxxxxxxxxxx> --- Changes in v17: Updated commit text as per comments on v16. This has been only compile tested as only the commit text has been updated. Link to v16: https://lore.kernel.org/all/20240429162048.2133512-3-quic_kriskura@xxxxxxxxxxx/ arch/arm64/boot/dts/qcom/sa8295p-adp.dts | 83 ++++++++++++++++++++++++ 1 file changed, 83 insertions(+) diff --git a/arch/arm64/boot/dts/qcom/sa8295p-adp.dts b/arch/arm64/boot/dts/qcom/sa8295p-adp.dts index 78e933c42c31..2fd1dafe63ce 100644 --- a/arch/arm64/boot/dts/qcom/sa8295p-adp.dts +++ b/arch/arm64/boot/dts/qcom/sa8295p-adp.dts @@ -9,6 +9,7 @@ #include <dt-bindings/gpio/gpio.h> #include <dt-bindings/regulator/qcom,rpmh-regulator.h> #include <dt-bindings/spmi/spmi.h> +#include <dt-bindings/pinctrl/qcom,pmic-gpio.h> #include "sa8540p.dtsi" #include "sa8540p-pmics.dtsi" @@ -109,6 +110,46 @@ edp3_connector_in: endpoint { }; }; + regulator-usb2-vbus { + compatible = "regulator-fixed"; + regulator-name = "USB2_VBUS"; + gpio = <&pmm8540c_gpios 9 GPIO_ACTIVE_HIGH>; + pinctrl-0 = <&usb2_en>; + pinctrl-names = "default"; + enable-active-high; + regulator-always-on; + }; + + regulator-usb3-vbus { + compatible = "regulator-fixed"; + regulator-name = "USB3_VBUS"; + gpio = <&pmm8540e_gpios 5 GPIO_ACTIVE_HIGH>; + pinctrl-0 = <&usb3_en>; + pinctrl-names = "default"; + enable-active-high; + regulator-always-on; + }; + + regulator-usb4-vbus { + compatible = "regulator-fixed"; + regulator-name = "USB4_VBUS"; + gpio = <&pmm8540g_gpios 5 GPIO_ACTIVE_HIGH>; + pinctrl-0 = <&usb4_en>; + pinctrl-names = "default"; + enable-active-high; + regulator-always-on; + }; + + regulator-usb5-vbus { + compatible = "regulator-fixed"; + regulator-name = "USB5_VBUS"; + gpio = <&pmm8540g_gpios 9 GPIO_ACTIVE_HIGH>; + pinctrl-0 = <&usb5_en>; + pinctrl-names = "default"; + enable-active-high; + regulator-always-on; + }; + reserved-memory { gpu_mem: gpu-mem@8bf00000 { reg = <0 0x8bf00000 0 0x2000>; @@ -637,6 +678,10 @@ &usb_1_qmpphy { status = "okay"; }; +&usb_2 { + status = "okay"; +}; + &usb_2_hsphy0 { vdda-pll-supply = <&vreg_l5a>; vdda18-supply = <&vreg_l7g>; @@ -697,6 +742,44 @@ max20411_en: max20411-en-state { }; }; +&pmm8540c_gpios { + usb2_en: usb2-en-state { + pins = "gpio9"; + function = "normal"; + qcom,drive-strength = <PMIC_GPIO_STRENGTH_HIGH>; + output-enable; + power-source = <0>; + }; +}; + +&pmm8540e_gpios { + usb3_en: usb3-en-state { + pins = "gpio5"; + function = "normal"; + qcom,drive-strength = <PMIC_GPIO_STRENGTH_HIGH>; + output-enable; + power-source = <0>; + }; +}; + +&pmm8540g_gpios { + usb4_en: usb4-en-state { + pins = "gpio5"; + function = "normal"; + qcom,drive-strength = <PMIC_GPIO_STRENGTH_HIGH>; + output-enable; + power-source = <0>; + }; + + usb5_en: usb5-en-state { + pins = "gpio9"; + function = "normal"; + qcom,drive-strength = <PMIC_GPIO_STRENGTH_HIGH>; + output-enable; + power-source = <0>; + }; +}; + &tlmm { pcie2a_default: pcie2a-default-state { clkreq-n-pins { -- 2.34.1
