From: Bartosz Golaszewski <bartosz.golaszewski@xxxxxxxxxx> Add a node for the PMU module of the QCA6391 present on the RB5 board. Assign its LDO power outputs to the existing Bluetooth module. Add a node for the PCIe port to sm8250.dtsi and define the WLAN node on it in the board's .dts and also make it consume the power outputs of the PMU. Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@xxxxxxxxxx> --- arch/arm64/boot/dts/qcom/qrb5165-rb5.dts | 103 +++++++++++++++++++++++++++---- arch/arm64/boot/dts/qcom/sm8250.dtsi | 2 +- 2 files changed, 93 insertions(+), 12 deletions(-) diff --git a/arch/arm64/boot/dts/qcom/qrb5165-rb5.dts b/arch/arm64/boot/dts/qcom/qrb5165-rb5.dts index 70036a95cace..135bb00fe9c8 100644 --- a/arch/arm64/boot/dts/qcom/qrb5165-rb5.dts +++ b/arch/arm64/boot/dts/qcom/qrb5165-rb5.dts @@ -108,6 +108,67 @@ lt9611_3v3: lt9611-3v3 { regulator-always-on; }; + qca6390-pmu { + compatible = "qcom,qca6390-pmu"; + + pinctrl-names = "default"; + pinctrl-0 = <&bt_en_state>, <&wlan_en_state>; + + vddaon-supply = <&vreg_s6a_0p95>; + vddpmu-supply = <&vreg_s2f_0p95>; + vddrfa0p95-supply = <&vreg_s2f_0p95>; + vddrfa1p3-supply = <&vreg_s8c_1p3>; + vddrfa1p9-supply = <&vreg_s5a_1p9>; + vddpcie1p3-supply = <&vreg_s8c_1p3>; + vddpcie1p9-supply = <&vreg_s5a_1p9>; + vddio-supply = <&vreg_s4a_1p8>; + + wlan-enable-gpios = <&tlmm 20 GPIO_ACTIVE_HIGH>; + bt-enable-gpios = <&tlmm 21 GPIO_ACTIVE_HIGH>; + + regulators { + vreg_pmu_rfa_cmn: ldo0 { + regulator-name = "vreg_pmu_rfa_cmn"; + }; + + vreg_pmu_aon_0p59: ldo1 { + regulator-name = "vreg_pmu_aon_0p59"; + }; + + vreg_pmu_wlcx_0p8: ldo2 { + regulator-name = "vreg_pmu_wlcx_0p8"; + }; + + vreg_pmu_wlmx_0p85: ldo3 { + regulator-name = "vreg_pmu_wlmx_0p85"; + }; + + vreg_pmu_btcmx_0p85: ldo4 { + regulator-name = "vreg_pmu_btcmx_0p85"; + }; + + vreg_pmu_rfa_0p8: ldo5 { + regulator-name = "vreg_pmu_rfa_0p8"; + }; + + vreg_pmu_rfa_1p2: ldo6 { + regulator-name = "vreg_pmu_rfa_1p2"; + }; + + vreg_pmu_rfa_1p7: ldo7 { + regulator-name = "vreg_pmu_rfa_1p7"; + }; + + vreg_pmu_pcie_0p9: ldo8 { + regulator-name = "vreg_pmu_pcie_0p9"; + }; + + vreg_pmu_pcie_1p8: ldo9 { + regulator-name = "vreg_pmu_pcie_1p8"; + }; + }; + }; + thermal-zones { conn-thermal { polling-delay-passive = <0>; @@ -734,6 +795,23 @@ &pcie0_phy { vdda-pll-supply = <&vreg_l9a_1p2>; }; +&pcieport0 { + wifi@0 { + compatible = "pci17cb,1101"; + reg = <0x10000 0x0 0x0 0x0 0x0>; + + vddrfacmn-supply = <&vreg_pmu_rfa_cmn>; + vddaon-supply = <&vreg_pmu_aon_0p59>; + vddwlcx-supply = <&vreg_pmu_wlcx_0p8>; + vddwlmx-supply = <&vreg_pmu_wlmx_0p85>; + vddrfa0p8-supply = <&vreg_pmu_rfa_0p8>; + vddrfa1p2-supply = <&vreg_pmu_rfa_1p2>; + vddrfa1p7-supply = <&vreg_pmu_rfa_1p7>; + vddpcie0p9-supply = <&vreg_pmu_pcie_0p9>; + vddpcie1p8-supply = <&vreg_pmu_pcie_1p8>; + }; +}; + &pcie1 { status = "okay"; }; @@ -1303,6 +1381,14 @@ sdc2_card_det_n: sd-card-det-n-state { function = "gpio"; bias-pull-up; }; + + wlan_en_state: wlan-default-state { + pins = "gpio20"; + function = "gpio"; + drive-strength = <16>; + output-low; + bias-pull-up; + }; }; &uart6 { @@ -1311,17 +1397,12 @@ &uart6 { bluetooth { compatible = "qcom,qca6390-bt"; - pinctrl-names = "default"; - pinctrl-0 = <&bt_en_state>; - - enable-gpios = <&tlmm 21 GPIO_ACTIVE_HIGH>; - - vddio-supply = <&vreg_s4a_1p8>; - vddpmu-supply = <&vreg_s2f_0p95>; - vddaon-supply = <&vreg_s6a_0p95>; - vddrfa0p9-supply = <&vreg_s2f_0p95>; - vddrfa1p3-supply = <&vreg_s8c_1p3>; - vddrfa1p9-supply = <&vreg_s5a_1p9>; + vddrfacmn-supply = <&vreg_pmu_rfa_cmn>; + vddaon-supply = <&vreg_pmu_aon_0p59>; + vddbtcmx-supply = <&vreg_pmu_btcmx_0p85>; + vddrfa0p8-supply = <&vreg_pmu_rfa_0p8>; + vddrfa1p2-supply = <&vreg_pmu_rfa_1p2>; + vddrfa1p7-supply = <&vreg_pmu_rfa_1p7>; }; }; diff --git a/arch/arm64/boot/dts/qcom/sm8250.dtsi b/arch/arm64/boot/dts/qcom/sm8250.dtsi index 759e0822b3ac..b32bd849df44 100644 --- a/arch/arm64/boot/dts/qcom/sm8250.dtsi +++ b/arch/arm64/boot/dts/qcom/sm8250.dtsi @@ -2204,7 +2204,7 @@ pcie0: pcie@1c00000 { status = "disabled"; - pcie@0 { + pcieport0: pcie@0 { device_type = "pci"; reg = <0x0 0x0 0x0 0x0 0x0>; bus-range = <0x01 0xff>; -- 2.43.0