On ipq9574, there are 4 PCIe controllers. Describe the pcie2 and pcie3
nodes, and their PHYs in devicetree.
The pcie0 and pcie1 controllers use a gen3x1 PHY, which is not
currently supported. Hence, only pcie2 and pcie3 are described. Only
pcie2 was tested because my devboard only has conenctions to pcie2.
Signed-off-by: Alexandru Gagniuc <mr.nuke.me@xxxxxxxxx>
---
arch/arm64/boot/dts/qcom/ipq9574.dtsi | 178 +++++++++++++++++++++++++-
1 file changed, 176 insertions(+), 2 deletions(-)
diff --git a/arch/arm64/boot/dts/qcom/ipq9574.dtsi b/arch/arm64/boot/dts/qcom/ipq9574.dtsi
index 7f2e5cbf3bbb..c391886cf9ab 100644
--- a/arch/arm64/boot/dts/qcom/ipq9574.dtsi
+++ b/arch/arm64/boot/dts/qcom/ipq9574.dtsi
@@ -300,8 +300,8 @@ gcc: clock-controller@1800000 {
<0>,
<0>,
<0>,
- <0>,
- <0>,
+ <&pcie2_phy>,
+ <&pcie3_phy>,
<0>;
#clock-cells = <1>;
#reset-cells = <1>;
@@ -745,6 +745,180 @@ frame@b128000 {
status = "disabled";
};
};
+
+ pcie2_phy: phy@8c000 {
+ compatible = "qcom,ipq9574-qmp-gen3x2-pcie-phy";
+ reg = <0x0008c000 0x14f4>;
+
+ clocks = <&gcc GCC_PCIE2_AUX_CLK>,
+ <&gcc GCC_PCIE2_AHB_CLK>,
+ <&gcc GCC_PCIE2_PIPE_CLK>;
+ clock-names = "aux",
+ "cfg_ahb",
+ "pipe";
+
+ clock-output-names = "pcie_phy2_pipe_clk";
+ #clock-cells = <0>;
+ #phy-cells = <0>;
+
+ resets = <&gcc GCC_PCIE2_PHY_BCR>,
+ <&gcc GCC_PCIE2PHY_PHY_BCR>;
+ reset-names = "phy",
+ "common";
+ status = "disabled";
+ };
+
+ pcie3_phy: phy@f4000 {
+ compatible = "qcom,ipq9574-qmp-gen3x2-pcie-phy";
+ reg = <0x000f4000 0x14f4>;
+
+ clocks = <&gcc GCC_PCIE3_AUX_CLK>,
+ <&gcc GCC_PCIE3_AHB_CLK>,
+ <&gcc GCC_PCIE3_PIPE_CLK>;
+ clock-names = "aux",
+ "cfg_ahb",
+ "pipe";
+
+ clock-output-names = "pcie_phy3_pipe_clk";
+ #clock-cells = <0>;
+ #phy-cells = <0>;
+
+ resets = <&gcc GCC_PCIE3_PHY_BCR>,
+ <&gcc GCC_PCIE3PHY_PHY_BCR>;
+ reset-names = "phy",
+ "common";
+ status = "disabled";
+ };
+
+ /* TODO: Populate pcie0/pcie1 when gen3x1 phy support is added. */
+
+ pcie2: pcie@20000000 {
+ compatible = "qcom,pcie-ipq9574";
+ reg = <0x20000000 0xf1d>,
+ <0x20000f20 0xa8>,
+ <0x20001000 0x1000>,
+ <0x00088000 0x4000>,
+ <0x20100000 0x1000>;
+ reg-names = "dbi", "elbi", "atu", "parf", "config";
+
+ ranges = <0x81000000 0x0 0x20200000 0x20200000 0x0 0x00100000>,
+ <0x82000000 0x0 0x20300000 0x20300000 0x0 0x07d00000>;
+
+ device_type = "pci";
+ linux,pci-domain = <3>;
+ bus-range = <0x00 0xff>;
+ num-lanes = <2>;
+ max-link-speed = <3>;
+ #address-cells = <3>;
+ #size-cells = <2>;
+
+ phys = <&pcie2_phy>;
+ phy-names = "pciephy";
+
+ interrupts = <GIC_SPI 126 IRQ_TYPE_LEVEL_HIGH>;
+ interrupt-names = "msi";
+
+ #interrupt-cells = <1>;
+ interrupt-map-mask = <0 0 0 0x7>;
+ interrupt-map = <0 0 0 1 &intc 0 0 164 IRQ_TYPE_LEVEL_HIGH>,
+ <0 0 0 2 &intc 0 0 165 IRQ_TYPE_LEVEL_HIGH>,
+ <0 0 0 3 &intc 0 0 186 IRQ_TYPE_LEVEL_HIGH>,
+ <0 0 0 4 &intc 0 0 187 IRQ_TYPE_LEVEL_HIGH>;
+
+ clocks = <&gcc GCC_PCIE2_AXI_M_CLK>,
+ <&gcc GCC_PCIE2_AXI_S_CLK>,
+ <&gcc GCC_PCIE2_AXI_S_BRIDGE_CLK>,
+ <&gcc GCC_ANOC_PCIE2_2LANE_M_CLK>,
+ <&gcc GCC_SNOC_PCIE2_2LANE_S_CLK>,
+ <&gcc GCC_PCIE2_RCHNG_CLK>;
+ clock-names = "axi_m",
+ "axi_s",
+ "axi_bridge",
+ "rchng";
+
+ resets = <&gcc GCC_PCIE2_PIPE_ARES>,
+ <&gcc GCC_PCIE2_AUX_ARES>,
+ <&gcc GCC_PCIE2_CORE_STICKY_ARES>,
+ <&gcc GCC_PCIE2_AXI_M_ARES>,
+ <&gcc GCC_PCIE2_AXI_S_ARES>,
+ <&gcc GCC_PCIE2_AXI_S_STICKY_ARES>,
+ <&gcc GCC_PCIE2_AXI_M_STICKY_ARES>,
+ <&gcc GCC_PCIE2_AHB_ARES>;
+ reset-names = "pipe",
+ "aux",
+ "sticky",
+ "axi_m",
+ "axi_s",
+ "axi_s_sticky",
+ "axi_m_sticky",
+ "ahb";
+ status = "disabled";
+ };
+
+ pcie3: pcie@18000000 {
+ compatible = "qcom,pcie-ipq9574";
+ reg = <0x18000000 0xf1d>,
+ <0x18000f20 0xa8>,
+ <0x18001000 0x1000>,
+ <0x000f0000 0x4000>,
+ <0x18100000 0x1000>;
+ reg-names = "dbi", "elbi", "atu", "parf", "config";
+
+ ranges = <0x81000000 0x0 0x18200000 0x18200000 0x0 0x00100000>,
+ <0x82000000 0x0 0x18300000 0x18300000 0x0 0x07d00000>;
+
+ device_type = "pci";
+ linux,pci-domain = <4>;
+ bus-range = <0x00 0xff>;
+ num-lanes = <2>;
+ max-link-speed = <3>;
+ #address-cells = <3>;
+ #size-cells = <2>;
+
+ phys = <&pcie3_phy>;
+ phy-names = "pciephy";
+
+ interrupts = <GIC_SPI 189 IRQ_TYPE_LEVEL_HIGH>;
+ interrupt-names = "msi";
+
+ #interrupt-cells = <1>;
+ interrupt-map-mask = <0 0 0 0x7>;
+ interrupt-map = <0 0 0 1 &intc 0 0 189 IRQ_TYPE_LEVEL_HIGH>,
+ <0 0 0 2 &intc 0 0 190 IRQ_TYPE_LEVEL_HIGH>,
+ <0 0 0 3 &intc 0 0 192 IRQ_TYPE_LEVEL_HIGH>,
+ <0 0 0 4 &intc 0 0 192 IRQ_TYPE_LEVEL_HIGH>;
+
+ clocks = <&gcc GCC_PCIE3_AXI_M_CLK>,
+ <&gcc GCC_PCIE3_AXI_S_CLK>,
+ <&gcc GCC_PCIE3_AXI_S_BRIDGE_CLK>,
+ <&gcc GCC_ANOC_PCIE3_2LANE_M_CLK>,
+ <&gcc GCC_SNOC_PCIE3_2LANE_S_CLK>,
+ <&gcc GCC_PCIE3_RCHNG_CLK>;
+ clock-names = "axi_m",
+ "axi_s",
+ "axi_bridge",
+ "anoc",
+ "snoc",
+ "rchng";
+
+ resets = <&gcc GCC_PCIE3_PIPE_ARES>,
+ <&gcc GCC_PCIE3_AUX_ARES>,
+ <&gcc GCC_PCIE3_CORE_STICKY_ARES>,
+ <&gcc GCC_PCIE3_AXI_M_ARES>,
+ <&gcc GCC_PCIE3_AXI_S_ARES>,
+ <&gcc GCC_PCIE3_AXI_S_STICKY_ARES>,
+ <&gcc GCC_PCIE3_AXI_M_STICKY_ARES>,
+ <&gcc GCC_PCIE3_AHB_ARES>;
+ reset-names = "pipe",
+ "aux",
+ "sticky",
+ "axi_m",
+ "axi_s",
+ "axi_s_sticky",
+ "axi_m_sticky",
+ "ahb";
+ status = "disabled";
+ };
};
thermal-zones {
--
2.40.1
