On 01/21/2016 12:43 PM, Archit Taneja wrote:
Add DT bindings document for the Qualcomm NAND controller driver.
Missed on inserting a "Reviewed-by" from Boris here.
Acked-by: Rob Herring <robh@xxxxxxxxxx>
Signed-off-by: Archit Taneja <architt@xxxxxxxxxxxxxx>
---
.../devicetree/bindings/mtd/qcom_nandc.txt | 86 ++++++++++++++++++++++
1 file changed, 86 insertions(+)
create mode 100644 Documentation/devicetree/bindings/mtd/qcom_nandc.txt
diff --git a/Documentation/devicetree/bindings/mtd/qcom_nandc.txt b/Documentation/devicetree/bindings/mtd/qcom_nandc.txt
new file mode 100644
index 0000000..70dd511
--- /dev/null
+++ b/Documentation/devicetree/bindings/mtd/qcom_nandc.txt
@@ -0,0 +1,86 @@
+* Qualcomm NAND controller
+
+Required properties:
+- compatible: should be "qcom,ipq806x-nand"
+- reg: MMIO address range
+- clocks: must contain core clock and always on clock
+- clock-names: must contain "core" for the core clock and "aon" for the
+ always on clock
+- dmas: DMA specifier, consisting of a phandle to the ADM DMA
+ controller node and the channel number to be used for
+ NAND. Refer to dma.txt and qcom_adm.txt for more details
+- dma-names: must be "rxtx"
+- qcom,cmd-crci: must contain the ADM command type CRCI block instance
+ number specified for the NAND controller on the given
+ platform
+- qcom,data-crci: must contain the ADM data type CRCI block instance
+ number specified for the NAND controller on the given
+ platform
+- #address-cells: <1> - subnodes give the chip-select number
+- #size-cells: <0>
+
+* NAND chip-select
+
+Each controller may contain one or more subnodes to represent enabled
+chip-selects which (may) contain NAND flash chips. Their properties are as
+follows.
+
+Required properties:
+- compatible: should contain "qcom,nandcs"
+- reg: a single integer representing the chip-select
+ number (e.g., 0, 1, 2, etc.)
+- #address-cells: see partition.txt
+- #size-cells: see partition.txt
+- nand-ecc-strength: see nand.txt
+- nand-ecc-step-size: must be 512. see nand.txt for more details.
+
+Optional properties:
+- nand-bus-width: see nand.txt
+
+Each nandcs device node may optionally contain a 'partitions' sub-node, which
+further contains sub-nodes describing the flash partition mapping. See
+partition.txt for more detail.
+
+Example:
+
+nand@1ac00000 {
+ compatible = "qcom,ebi2-nandc";
+ reg = <0x1ac00000 0x800>;
+
+ clocks = <&gcc EBI2_CLK>,
+ <&gcc EBI2_AON_CLK>;
+ clock-names = "core", "aon";
+
+ dmas = <&adm_dma 3>;
+ dma-names = "rxtx";
+ qcom,cmd-crci = <15>;
+ qcom,data-crci = <3>;
+
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ nandcs@0 {
+ compatible = "qcom,nandcs";
+ reg = <0>;
+
+ nand-ecc-strength = <4>;
+ nand-ecc-step-size = <512>;
+ nand-bus-width = <8>;
+
+ partitions {
+ compatible = "fixed-partitions";
+ #address-cells = <1>;
+ #size-cells = <1>;
+
+ partition@0 {
+ label = "boot-nand";
+ reg = <0 0x58a0000>;
+ };
+
+ partition@58a0000 {
+ label = "fs-nand";
+ reg = <0x58a0000 0x4000000>;
+ };
+ };
+ };
+};
--
The Qualcomm Innovation Center, Inc. is a member of the Code Aurora
Forum, hosted by The Linux Foundation
--
To unsubscribe from this list: send the line "unsubscribe linux-arm-msm" in
the body of a message to majordomo@xxxxxxxxxxxxxxx
More majordomo info at http://vger.kernel.org/majordomo-info.html
