Re: [PATCH V6 0/6] i2c: qup: Add support for v2 tags and bam dma

[Date Prev][Date Next][Thread Prev][Thread Next][Date Index][Thread Index]

 



Added SMB support on top of these patches and tested  i2c with ipmitool.
It works as expected.
Tested-by: ntelkar@xxxxxxxxxxxxxx

> i2c: qup: Add support for v2 tags and bam dma
>
> QUP from version 2.1.1 onwards, supports a new format of i2c command tags.
> Tag codes instructs the controller to perform a operation like read/write.
> This new tagging version supports and is required for adding bam dma
> capabilities. V2 tags supports transfer of more than 256 bytes in a single
> i2c
> transaction. Also adding bam dma support facilitates transferring each
> i2c_msg
> in i2c_msgs without a 'stop' bit in between which is required for some of
> the clients.
>
> Tested this series on apq8074 dragon board eeprom client on i2c bus1
>
> [V6] Added review tags and fixed a checkpatch warning in patch 4/6.
>
> [V5] Addressed few more comments from Ivan T. Ivanov.
>      Squashed patch 2 and 3 as no point in having only few lines of
>      common code between v1 and v2 tags for increased complexity.
>      Couple of non functional review comments fixes in patch 3, 4.
>      Added a change in patch 4 to have proper transfer completion in
>      a corner case. patch 5, 6 unchanged.
>
> [V4] Added a patch to factor out some common code.
>      Removed support for freq > 400KHZ as per comments.
>      Addressed comments from Ivan T. Ivanov to keep the code for
>      V2 support in a separate path.
>      Changed the authorship of V2 tags support patch.
>
> [V3] Added support to coalesce each i2c_msg in i2c_msgs for fifo and
>      block mode in Patch 2. Also addressed further code comments.
>
>      http://comments.gmane.org/gmane.linux.drivers.i2c/22497
>
> [V2] Addressed comments from Ivan T. Ivanov, Andy Gross [v1] Initial
> Version
>
> Sricharan R (6):
>   i2c: qup: Change qup_wait_writeready function to use for all timeouts
>   i2c: qup: Add V2 tags support
>   i2c: qup: Transfer each i2c_msg in i2c_msgs without a stop bit
>   i2c: qup: Add bam dma capabilities
>   dts: msm8974: Add blsp2_bam dma node
>   dts: msm8974: Add dma channels for blsp2_i2c1 node
>
>  arch/arm/boot/dts/qcom-msm8974.dtsi |  14 +-
>  drivers/i2c/busses/i2c-qup.c        | 922
> ++++++++++++++++++++++++++++++++++--
>  2 files changed, 887 insertions(+), 49 deletions(-)
>
> --
> QUALCOMM INDIA, on behalf of Qualcomm Innovation Center, Inc. is a member
> of Code Aurora Forum, hosted by The Linux Foundation
>
>


--
To unsubscribe from this list: send the line "unsubscribe linux-arm-msm" in
the body of a message to majordomo@xxxxxxxxxxxxxxx
More majordomo info at  http://vger.kernel.org/majordomo-info.html



[Index of Archives]     [Linux ARM Kernel]     [Linux ARM]     [Linux Omap]     [Fedora ARM]     [Linux for Sparc]     [IETF Annouce]     [Security]     [Bugtraq]     [Linux MIPS]     [ECOS]     [Asterisk Internet PBX]     [Linux API]

  Powered by Linux