On 11/30/2023 11:05 PM, Dmitry Baryshkov wrote:
On Fri, 1 Dec 2023 at 01:36, Abhinav Kumar <quic_abhinavk@xxxxxxxxxxx> wrote:
On 8/30/2023 5:00 PM, Dmitry Baryshkov wrote:
On Thu, 31 Aug 2023 at 01:50, Abhinav Kumar <quic_abhinavk@xxxxxxxxxxx> wrote:
CDM block comes with its own set of registers and operations
which can be done. In-line with other hardware sub-blocks, this
change adds the dpu_hw_cdm abstraction for the CDM block.
Signed-off-by: Abhinav Kumar <quic_abhinavk@xxxxxxxxxxx>
---
drivers/gpu/drm/msm/Makefile | 1 +
drivers/gpu/drm/msm/disp/dpu1/dpu_hw_cdm.c | 272 ++++++++++++++++++++
drivers/gpu/drm/msm/disp/dpu1/dpu_hw_cdm.h | 135 ++++++++++
drivers/gpu/drm/msm/disp/dpu1/dpu_hw_mdss.h | 1 +
4 files changed, 409 insertions(+)
create mode 100644 drivers/gpu/drm/msm/disp/dpu1/dpu_hw_cdm.c
create mode 100644 drivers/gpu/drm/msm/disp/dpu1/dpu_hw_cdm.h
diff --git a/drivers/gpu/drm/msm/Makefile b/drivers/gpu/drm/msm/Makefile
index 8d02d8c33069..2010cb1ca995 100644
--- a/drivers/gpu/drm/msm/Makefile
+++ b/drivers/gpu/drm/msm/Makefile
@@ -63,6 +63,7 @@ msm-$(CONFIG_DRM_MSM_DPU) += \
disp/dpu1/dpu_encoder_phys_wb.o \
disp/dpu1/dpu_formats.o \
disp/dpu1/dpu_hw_catalog.o \
+ disp/dpu1/dpu_hw_cdm.o \
disp/dpu1/dpu_hw_ctl.o \
disp/dpu1/dpu_hw_dsc.o \
disp/dpu1/dpu_hw_dsc_1_2.o \
diff --git a/drivers/gpu/drm/msm/disp/dpu1/dpu_hw_cdm.c b/drivers/gpu/drm/msm/disp/dpu1/dpu_hw_cdm.c
new file mode 100644
index 000000000000..a2f7ee8f54e4
--- /dev/null
+++ b/drivers/gpu/drm/msm/disp/dpu1/dpu_hw_cdm.c
@@ -0,0 +1,272 @@
+// SPDX-License-Identifier: GPL-2.0-only
+/*
+ * Copyright (c) 2023, The Linux Foundation. All rights reserved.
+ */
+
+#include <drm/drm_managed.h>
+
+#include "dpu_hw_mdss.h"
+#include "dpu_hw_util.h"
+#include "dpu_hw_catalog.h"
+#include "dpu_hw_cdm.h"
+#include "dpu_kms.h"
+
+#define CDM_CSC_10_OPMODE 0x000
+#define CDM_CSC_10_BASE 0x004
+
+#define CDM_CDWN2_OP_MODE 0x100
+#define CDM_CDWN2_CLAMP_OUT 0x104
+#define CDM_CDWN2_PARAMS_3D_0 0x108
+#define CDM_CDWN2_PARAMS_3D_1 0x10C
+#define CDM_CDWN2_COEFF_COSITE_H_0 0x110
+#define CDM_CDWN2_COEFF_COSITE_H_1 0x114
+#define CDM_CDWN2_COEFF_COSITE_H_2 0x118
+#define CDM_CDWN2_COEFF_OFFSITE_H_0 0x11C
+#define CDM_CDWN2_COEFF_OFFSITE_H_1 0x120
+#define CDM_CDWN2_COEFF_OFFSITE_H_2 0x124
+#define CDM_CDWN2_COEFF_COSITE_V 0x128
+#define CDM_CDWN2_COEFF_OFFSITE_V 0x12C
+#define CDM_CDWN2_OUT_SIZE 0x130
+
+#define CDM_HDMI_PACK_OP_MODE 0x200
+#define CDM_CSC_10_MATRIX_COEFF_0 0x004
+
+#define CDM_MUX 0x224
+
+/**
+ * Horizontal coefficients for cosite chroma downscale
+ * s13 representation of coefficients
+ */
+static u32 cosite_h_coeff[] = {0x00000016, 0x000001cc, 0x0100009e};
+
+/**
+ * Horizontal coefficients for offsite chroma downscale
+ */
+static u32 offsite_h_coeff[] = {0x000b0005, 0x01db01eb, 0x00e40046};
+
+/**
+ * Vertical coefficients for cosite chroma downscale
+ */
+static u32 cosite_v_coeff[] = {0x00080004};
+/**
+ * Vertical coefficients for offsite chroma downscale
+ */
+static u32 offsite_v_coeff[] = {0x00060002};
+
+static int dpu_hw_cdm_setup_csc_10bit(struct dpu_hw_cdm *ctx, struct dpu_csc_cfg *data)
+{
+ dpu_hw_csc_setup(&ctx->hw, CDM_CSC_10_MATRIX_COEFF_0, data, true);
Where was this defined?
Its in this file itself
+#define CDM_CSC_10_MATRIX_COEFF_0 0x004
+
+ return 0;
+}
+
+static int dpu_hw_cdm_setup_cdwn(struct dpu_hw_cdm *ctx, struct dpu_hw_cdm_cfg *cfg)
+{
+ struct dpu_hw_blk_reg_map *c = &ctx->hw;
+ u32 opmode = 0;
+ u32 out_size = 0;
+
+ if (cfg->output_bit_depth == CDM_CDWN_OUTPUT_10BIT)
+ opmode &= ~BIT(7);
+ else
+ opmode |= BIT(7);
+
+ /* ENABLE DWNS_H bit */
+ opmode |= BIT(1);
+
+ switch (cfg->h_cdwn_type) {
+ case CDM_CDWN_DISABLE:
+ /* CLEAR METHOD_H field */
+ opmode &= ~(0x18);
+ /* CLEAR DWNS_H bit */
+ opmode &= ~BIT(1);
+ break;
+ case CDM_CDWN_PIXEL_DROP:
+ /* Clear METHOD_H field (pixel drop is 0) */
+ opmode &= ~(0x18);
+ break;
+ case CDM_CDWN_AVG:
+ /* Clear METHOD_H field (Average is 0x1) */
+ opmode &= ~(0x18);
+ opmode |= (0x1 << 0x3);
+ break;
+ case CDM_CDWN_COSITE:
+ /* Clear METHOD_H field (Average is 0x2) */
+ opmode &= ~(0x18);
+ opmode |= (0x2 << 0x3);
+ /* Co-site horizontal coefficients */
+ DPU_REG_WRITE(c, CDM_CDWN2_COEFF_COSITE_H_0,
+ cosite_h_coeff[0]);
+ DPU_REG_WRITE(c, CDM_CDWN2_COEFF_COSITE_H_1,
+ cosite_h_coeff[1]);
+ DPU_REG_WRITE(c, CDM_CDWN2_COEFF_COSITE_H_2,
+ cosite_h_coeff[2]);
+ break;
+ case CDM_CDWN_OFFSITE:
+ /* Clear METHOD_H field (Average is 0x3) */
+ opmode &= ~(0x18);
+ opmode |= (0x3 << 0x3);
+
+ /* Off-site horizontal coefficients */
+ DPU_REG_WRITE(c, CDM_CDWN2_COEFF_OFFSITE_H_0,
+ offsite_h_coeff[0]);
+ DPU_REG_WRITE(c, CDM_CDWN2_COEFF_OFFSITE_H_1,
+ offsite_h_coeff[1]);
+ DPU_REG_WRITE(c, CDM_CDWN2_COEFF_OFFSITE_H_2,
+ offsite_h_coeff[2]);
+ break;
+ default:
+ pr_err("%s invalid horz down sampling type\n", __func__);
+ return -EINVAL;
+ }
+
+ /* ENABLE DWNS_V bit */
+ opmode |= BIT(2);
+
+ switch (cfg->v_cdwn_type) {
+ case CDM_CDWN_DISABLE:
+ /* CLEAR METHOD_V field */
+ opmode &= ~(0x60);
#define, GENMASK
+ /* CLEAR DWNS_V bit */
+ opmode &= ~BIT(2);
+ break;
+ case CDM_CDWN_PIXEL_DROP:
+ /* Clear METHOD_V field (pixel drop is 0) */
+ opmode &= ~(0x60);
+ break;
+ case CDM_CDWN_AVG:
+ /* Clear METHOD_V field (Average is 0x1) */
+ opmode &= ~(0x60);
+ opmode |= (0x1 << 0x5);
#define
+ break;
+ case CDM_CDWN_COSITE:
+ /* Clear METHOD_V field (Average is 0x2) */
+ opmode &= ~(0x60);
+ opmode |= (0x2 << 0x5);
+ /* Co-site vertical coefficients */
+ DPU_REG_WRITE(c,
+ CDM_CDWN2_COEFF_COSITE_V,
+ cosite_v_coeff[0]);
align to opening bracket
+ break;
+ case CDM_CDWN_OFFSITE:
+ /* Clear METHOD_V field (Average is 0x3) */
+ opmode &= ~(0x60);
+ opmode |= (0x3 << 0x5);
+
+ /* Off-site vertical coefficients */
+ DPU_REG_WRITE(c,
+ CDM_CDWN2_COEFF_OFFSITE_V,
+ offsite_v_coeff[0]);
align to opening bracket
+ break;
+ default:
+ return -EINVAL;
+ }
+
+ if (cfg->v_cdwn_type || cfg->h_cdwn_type)
+ opmode |= BIT(0); /* EN CDWN module */
#define
Ack to all comments about GENMASK and #define
+ else
+ opmode &= ~BIT(0);
+
+ out_size = (cfg->output_width & 0xFFFF) |
+ ((cfg->output_height & 0xFFFF) << 16);
+ DPU_REG_WRITE(c, CDM_CDWN2_OUT_SIZE, out_size);
+ DPU_REG_WRITE(c, CDM_CDWN2_OP_MODE, opmode);
+ DPU_REG_WRITE(c, CDM_CDWN2_CLAMP_OUT,
+ ((0x3FF << 16) | 0x0));
+
+ return 0;
+}
+
+int dpu_hw_cdm_enable(struct dpu_hw_cdm *ctx, struct dpu_hw_cdm_cfg *cdm)
+{
+ struct dpu_hw_blk_reg_map *c = &ctx->hw;
+ const struct dpu_format *fmt;
+ u32 opmode = 0;
+ u32 csc = 0;
+
+ if (!ctx || !cdm)
+ return -EINVAL;
+
+ fmt = cdm->output_fmt;
+
+ if (!DPU_FORMAT_IS_YUV(fmt))
+ return -EINVAL;
+
+ if (cdm->output_type == CDM_CDWN_OUTPUT_HDMI) {
+ if (fmt->chroma_sample != DPU_CHROMA_H1V2)
+ return -EINVAL; /*unsupported format */
+ opmode = BIT(0);
+ opmode |= (fmt->chroma_sample << 1);
+ }
+
+ csc |= BIT(2);
+ csc &= ~BIT(1);
+ csc |= BIT(0);
Can we get some sensible #defines for all this magic, please?
Ack, will do.
+
+ if (ctx && ctx->ops.bind_pingpong_blk)
+ ctx->ops.bind_pingpong_blk(ctx, true,
+ cdm->pp_id);
+
+ DPU_REG_WRITE(c, CDM_CSC_10_OPMODE, csc);
+ DPU_REG_WRITE(c, CDM_HDMI_PACK_OP_MODE, opmode);
+ return 0;
+}
+
+void dpu_hw_cdm_disable(struct dpu_hw_cdm *ctx)
+{
+ if (!ctx)
+ return;
+
+ if (ctx && ctx->ops.bind_pingpong_blk)
+ ctx->ops.bind_pingpong_blk(ctx, false, 0);
PINGPONG_NONE.
+}
+
+static void dpu_hw_cdm_bind_pingpong_blk(struct dpu_hw_cdm *ctx, bool enable,
+ const enum dpu_pingpong pp)
+{
+ struct dpu_hw_blk_reg_map *c;
+ int mux_cfg = 0xF;
+
+ if (!ctx || (enable && (pp < PINGPONG_0 || pp >= PINGPONG_MAX)))
+ return;
I'd say, this is useless. We don't have such checks in other
bind_pingpong_blk() callbacks.
Also there should be a guarding check for DPU >= 5.0 either here or at
the ops init.
Will add it at ops init
+
+ c = &ctx->hw;
+
+ if (enable)
+ mux_cfg = (pp - PINGPONG_0) & 0x7;
+
+ DPU_REG_WRITE(c, CDM_MUX, mux_cfg);
+}
+
+static void _setup_cdm_ops(struct dpu_hw_cdm_ops *ops, unsigned long features)
Please inline
OK
+{
+ ops->setup_csc_data = dpu_hw_cdm_setup_csc_10bit;
+ ops->setup_cdwn = dpu_hw_cdm_setup_cdwn;
+ ops->enable = dpu_hw_cdm_enable;
+ ops->disable = dpu_hw_cdm_disable;
+ ops->bind_pingpong_blk = dpu_hw_cdm_bind_pingpong_blk;
As you seem to call this function directly, we might as well drop the
callback from the ops.
There are two paths for the bind_pingpong_blk(). One is absorbed within
cdm_enable and cdm_disable calls to bind and unbind the pingpong resp.
And yes, for that we dont need a separate ops as its within the same file.
This will handle cases where we transition from YUV to non-YUV cases and
vice-versa without an encoder disable in between which I believe happens
in the IGT cases.
But the dpu_encoder_helper_phys_cleanup() path is only in the encoder
disable() path without a non-YUV frame in the middle so lets say we were
in YUV mode but then just disabled the encoder we do need the cleanup
there and since thats outside of the dpu_hw_cdm, we do need this op.
I agree we need to protect this with the DPU revision check.
+}
+
+struct dpu_hw_cdm *dpu_hw_cdm_init(const struct dpu_cdm_cfg *cfg, void __iomem *addr)
+{
+ struct dpu_hw_cdm *c;
+
+ c = kzalloc(sizeof(*c), GFP_KERNEL);
+ if (!c)
+ return ERR_PTR(-ENOMEM);
+
+ c->hw.blk_addr = addr + cfg->base;
+ c->hw.log_mask = DPU_DBG_MASK_CDM;
+
+ /* Assign ops */
+ c->idx = cfg->id;
+ c->caps = cfg;
+ _setup_cdm_ops(&c->ops, c->caps->features);
+
+ return c;
+}
+
+void dpu_hw_cdm_destroy(struct dpu_hw_cdm *cdm)
+{
+ kfree(cdm);
I'd prefer not to introduce another manual kzalloc/kfree pair, see
https://patchwork.freedesktop.org/series/120366/
I recall I did not want to have a manual kzalloc/kfree pair. But the
issue was I think this series was not merged that time (and is isnt
merged now either)
No response, no reviews since 15th August. Today is the 1st of December.
I'm close to deciding that unreviewed series have no issues and start
showing them to -next after a grace period of 1 month.
and this is the one which passes drm_dev to
dpu_rm_init. I thought maybe it was easier for you to absorb this change
into that series instead of me pulling that whole series to make this
one compile as we will not be adding new HW blocks after this for the
next 2 cycles. It will only be using existing ones.
If its too much trouble for you, I will rebase on top of that series but
I am pretty sure you will have to rebase and post that again anyway on
top of the current msm-next.
I am also going to do the same thing now with this series.
There were 4 patches in that series which didnt get a R-b. Perhaps
jessica can finish the reviews which she started on that one.
Leaving her a note on IRC would not have hurt like its a common practice
sometimes with other reviewers.
Now, do you want to rebase this on msm-next and re-send so that I can
rebase on top of yours?
So we can just decide that in whose rebase we will handle it.
+}
diff --git a/drivers/gpu/drm/msm/disp/dpu1/dpu_hw_cdm.h b/drivers/gpu/drm/msm/disp/dpu1/dpu_hw_cdm.h
new file mode 100644
index 000000000000..da60893a5c02
--- /dev/null
+++ b/drivers/gpu/drm/msm/disp/dpu1/dpu_hw_cdm.h
@@ -0,0 +1,135 @@
+/* SPDX-License-Identifier: GPL-2.0-only */
+/*
+ * Copyright (c) 2023, The Linux Foundation. All rights reserved.
+ */
+
+#ifndef _DPU_HW_CDM_H
+#define _DPU_HW_CDM_H
+
+#include "dpu_hw_mdss.h"
+#include "dpu_hw_top.h"
+
+struct dpu_hw_cdm;
+
+struct dpu_hw_cdm_cfg {
+ u32 output_width;
+ u32 output_height;
+ u32 output_bit_depth;
+ u32 h_cdwn_type;
+ u32 v_cdwn_type;
+ const struct dpu_format *output_fmt;
+ u32 output_type;
+ int pp_id;
+};
+
+enum dpu_hw_cdwn_type {
+ CDM_CDWN_DISABLE,
+ CDM_CDWN_PIXEL_DROP,
+ CDM_CDWN_AVG,
+ CDM_CDWN_COSITE,
+ CDM_CDWN_OFFSITE,
+};
+
+enum dpu_hw_cdwn_output_type {
+ CDM_CDWN_OUTPUT_HDMI,
+ CDM_CDWN_OUTPUT_WB,
+};
+
+enum dpu_hw_cdwn_output_bit_depth {
+ CDM_CDWN_OUTPUT_8BIT,
+ CDM_CDWN_OUTPUT_10BIT,
+};
+
+/**
+ * struct dpu_hw_cdm_ops : Interface to the chroma down Hw driver functions
+ * Assumption is these functions will be called after
+ * clocks are enabled
+ * @setup_csc: Programs the csc matrix
+ * @setup_cdwn: Sets up the chroma down sub module
+ * @enable: Enables the output to interface and programs the
+ * output packer
+ * @disable: Puts the cdm in bypass mode
+ * @bind_pingpong_blk: enable/disable the connection with pingpong which
+ * will feed pixels to this cdm
+ */
+struct dpu_hw_cdm_ops {
+ /**
+ * Programs the CSC matrix for conversion from RGB space to YUV space,
+ * it is optional to call this function as this matrix is automatically
+ * set during initialization, user should call this if it wants
+ * to program a different matrix than default matrix.
+ * @cdm: Pointer to the chroma down context structure
+ * @data Pointer to CSC configuration data
+ * return: 0 if success; error code otherwise
+ */
+ int (*setup_csc_data)(struct dpu_hw_cdm *cdm, struct dpu_csc_cfg *data);
+
+ /**
+ * Programs the Chroma downsample part.
+ * @cdm Pointer to chroma down context
+ * @cfg Pointer to the cdm configuration data
+ */
+ int (*setup_cdwn)(struct dpu_hw_cdm *cdm, struct dpu_hw_cdm_cfg *cfg);
+
+ /**
+ * Enable the CDM module
+ * @cdm Pointer to chroma down context
+ */
+ int (*enable)(struct dpu_hw_cdm *cdm, struct dpu_hw_cdm_cfg *cfg);
+
+ /**
+ * Disable the CDM module
+ * @cdm Pointer to chroma down context
+ */
+ void (*disable)(struct dpu_hw_cdm *cdm);
+
+ /**
+ * Enable/disable the connection with pingpong
+ * @cdm Pointer to chroma down context
+ * @enable Enable/disable control
+ * @pp pingpong block id.
+ */
+ void (*bind_pingpong_blk)(struct dpu_hw_cdm *cdm, bool enable,
+ const enum dpu_pingpong pp);
+};
+
+/**
+ * struct dpu_hw_cdm - cdm description
+ * @base: Hardware block base structure
+ * @hw: Block hardware details
+ * @idx: CDM index
+ * @caps: Pointer to cdm_cfg
+ * @ops: handle to operations possible for this CDM
+ */
+struct dpu_hw_cdm {
+ struct dpu_hw_blk base;
+ struct dpu_hw_blk_reg_map hw;
+
+ /* chroma down */
+ const struct dpu_cdm_cfg *caps;
+ enum dpu_cdm idx;
+
+ /* ops */
+ struct dpu_hw_cdm_ops ops;
+};
+
+/**
+ * dpu_hw_cdm_init - initializes the cdm hw driver object.
+ * should be called once before accessing every cdm.
+ * @cdm: CDM catalog entry for which driver object is required
+ * @addr : mapped register io address of MDSS
+ */
+struct dpu_hw_cdm *dpu_hw_cdm_init(const struct dpu_cdm_cfg *cdm, void __iomem *addr);
+
+/**
+ * dpu_hw_cdm_destroy - destroys cdm driver context
+ * @cdm: Pointer to cdm driver context returned by dpu_hw_cdm_init
+ */
+void dpu_hw_cdm_destroy(struct dpu_hw_cdm *cdm);
+
+static inline struct dpu_hw_cdm *to_dpu_hw_cdm(struct dpu_hw_blk *hw)
+{
+ return container_of(hw, struct dpu_hw_cdm, base);
+}
+
+#endif /*_DPU_HW_CDM_H */
diff --git a/drivers/gpu/drm/msm/disp/dpu1/dpu_hw_mdss.h b/drivers/gpu/drm/msm/disp/dpu1/dpu_hw_mdss.h
index 4d6dba18caf0..34f943102499 100644
--- a/drivers/gpu/drm/msm/disp/dpu1/dpu_hw_mdss.h
+++ b/drivers/gpu/drm/msm/disp/dpu1/dpu_hw_mdss.h
@@ -463,6 +463,7 @@ struct dpu_mdss_color {
#define DPU_DBG_MASK_ROT (1 << 9)
#define DPU_DBG_MASK_DSPP (1 << 10)
#define DPU_DBG_MASK_DSC (1 << 11)
+#define DPU_DBG_MASK_CDM (1 << 12)
/**
* struct dpu_hw_tear_check - Struct contains parameters to configure
--
2.40.1
--
With best wishes
Dmitry
