Re: [PATCH v3 5/6] arm64: dts: qcom: sdm845: Add OPP table support to UFSHC

[Date Prev][Date Next][Thread Prev][Thread Next][Date Index][Thread Index]

 



On Mon, Sep 11, 2023 at 04:15:10PM +0300, Dmitry Baryshkov wrote:
> On 31/07/2023 19:33, Manivannan Sadhasivam wrote:
> > From: Krzysztof Kozlowski <krzysztof.kozlowski@xxxxxxxxxx>
> > 
> > UFS host controller, when scaling gears, should choose appropriate
> > performance state of RPMh power domain controller along with clock
> > frequency. So let's add the OPP table support to specify both clock
> > frequency and RPMh performance states replacing the old "freq-table-hz"
> > property.
> > 
> > Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@xxxxxxxxxx>
> > [mani: Splitted pd change and used rpmhpd_opp_low_svs]
> > Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@xxxxxxxxxx>
> > ---
> >   arch/arm64/boot/dts/qcom/sdm845.dtsi | 42 +++++++++++++++++++++-------
> >   1 file changed, 32 insertions(+), 10 deletions(-)
> > 
> > diff --git a/arch/arm64/boot/dts/qcom/sdm845.dtsi b/arch/arm64/boot/dts/qcom/sdm845.dtsi
> > index 055ca80c0075..2ea6eb44953e 100644
> > --- a/arch/arm64/boot/dts/qcom/sdm845.dtsi
> > +++ b/arch/arm64/boot/dts/qcom/sdm845.dtsi
> > @@ -2605,22 +2605,44 @@ ufs_mem_hc: ufshc@1d84000 {
> >   				<&gcc GCC_UFS_PHY_RX_SYMBOL_0_CLK>,
> >   				<&gcc GCC_UFS_PHY_RX_SYMBOL_1_CLK>,
> >   				<&gcc GCC_UFS_PHY_ICE_CORE_CLK>;
> > -			freq-table-hz =
> > -				<50000000 200000000>,
> > -				<0 0>,
> > -				<0 0>,
> > -				<37500000 150000000>,
> > -				<0 0>,
> > -				<0 0>,
> > -				<0 0>,
> > -				<0 0>,
> > -				<75000000 300000000>;
> > +
> > +			operating-points-v2 = <&ufs_opp_table>;
> >   			interconnects = <&aggre1_noc MASTER_UFS_MEM 0 &mem_noc SLAVE_EBI1 0>,
> >   					<&gladiator_noc MASTER_APPSS_PROC 0 &config_noc SLAVE_UFS_MEM_CFG 0>;
> >   			interconnect-names = "ufs-ddr", "cpu-ufs";
> >   			status = "disabled";
> > +
> > +			ufs_opp_table: opp-table {
> > +				compatible = "operating-points-v2";
> > +
> > +				opp-50000000 {
> > +					opp-hz = /bits/ 64 <50000000>,
> > +						 /bits/ 64 <0>,
> > +						 /bits/ 64 <0>,
> > +						 /bits/ 64 <37500000>,
> > +						 /bits/ 64 <0>,
> > +						 /bits/ 64 <0>,
> > +						 /bits/ 64 <0>,
> > +						 /bits/ 64 <0>,
> > +						 /bits/ 64 <75000000>;
> > +					required-opps = <&rpmhpd_opp_low_svs>;
> > +				};
> 
> I'd say, I'm still slightly unhappy about the 0 clock rates here.

Neither do I. But it is the only viable option I could found.

> We need only three clocks here: core, core_clk_unipro and optional
> ice_core_clk. Can we modify ufshcd_parse_operating_points() to pass only
> these two or three clock names to devm_pm_opp_set_config() ? The OPP core
> doesn't need to know about all the rest of the clocks.
> 

We need to enable/disable all of the clocks, but only need to control the rate
for these 3 clocks. So we cannot just use 3 clocks.

If the OPP table has only 3 entries (omitting the gate-only clocks), then we
need some hack in the driver to match the rates against the clock entries. Doing
so will result in hardcoding the clock info in the driver which I do not want to
do.

If we have something like "opp-hz-names" to relate the rates to clock-names, it
might do the job. But it needs some input from Viresh.

- Mani

> > +
> > +				opp-200000000 {
> > +					opp-hz = /bits/ 64 <200000000>,
> > +						 /bits/ 64 <0>,
> > +						 /bits/ 64 <0>,
> > +						 /bits/ 64 <150000000>,
> > +						 /bits/ 64 <0>,
> > +						 /bits/ 64 <0>,
> > +						 /bits/ 64 <0>,
> > +						 /bits/ 64 <0>,
> > +						 /bits/ 64 <300000000>;
> > +					required-opps = <&rpmhpd_opp_nom>;
> > +				};
> > +			};
> >   		};
> >   		ufs_mem_phy: phy@1d87000 {
> 
> -- 
> With best wishes
> Dmitry
> 

-- 
மணிவண்ணன் சதாசிவம்



[Index of Archives]     [Linux ARM Kernel]     [Linux ARM]     [Linux Omap]     [Fedora ARM]     [Linux for Sparc]     [IETF Annouce]     [Security]     [Bugtraq]     [Linux MIPS]     [ECOS]     [Asterisk Internet PBX]     [Linux API]

  Powered by Linux