Re: [PATCH 4/5] arm64: dts: qcom: ipq5018: Add USB related nodes

[Date Prev][Date Next][Thread Prev][Thread Next][Date Index][Thread Index]

 




On 8/31/2023 1:45 AM, Dmitry Baryshkov wrote:
On Fri, 25 Aug 2023 at 12:37, Nitheesh Sekar <quic_nsekar@xxxxxxxxxxx> wrote:
Add USB phy and controller nodes.

Co-developed-by: Amandeep Singh <quic_amansing@xxxxxxxxxxx>
Signed-off-by: Amandeep Singh <quic_amansing@xxxxxxxxxxx>
Signed-off-by: Nitheesh Sekar <quic_nsekar@xxxxxxxxxxx>
---
  arch/arm64/boot/dts/qcom/ipq5018.dtsi | 54 +++++++++++++++++++++++++++
  1 file changed, 54 insertions(+)

diff --git a/arch/arm64/boot/dts/qcom/ipq5018.dtsi b/arch/arm64/boot/dts/qcom/ipq5018.dtsi
index 9f13d2dcdfd5..ff477923a823 100644
--- a/arch/arm64/boot/dts/qcom/ipq5018.dtsi
+++ b/arch/arm64/boot/dts/qcom/ipq5018.dtsi
@@ -238,6 +238,60 @@
                                 status = "disabled";
                         };
                 };
+
+               usbphy0: phy@5b000 {
+                       compatible = "qcom,ipq5018-usb-hsphy";
+                       reg = <0x0005b000 0x120>;
+
+                       clocks = <&gcc GCC_USB0_PHY_CFG_AHB_CLK>;
+
+                       resets = <&gcc GCC_QUSB2_0_PHY_BCR>;
+
+                       #phy-cells = <0>;
+
+                       status = "disabled";
+               };
+
+               usb: usb2@8a00000 {
+                       compatible = "qcom,ipq5018-dwc3", "qcom,dwc3";
+                       reg = <0x08af8800 0x400>;
+
+                       interrupts = <GIC_SPI 62 IRQ_TYPE_LEVEL_HIGH>;
+                       interrupt-names = "hs_phy_irq";
+
+                       clocks = <&gcc GCC_USB0_MASTER_CLK>,
+                                <&gcc GCC_SYS_NOC_USB0_AXI_CLK>,
+                                <&gcc GCC_USB0_SLEEP_CLK>,
+                                <&gcc GCC_USB0_MOCK_UTMI_CLK>;
+                       clock-names = "core",
+                                     "iface",
+                                     "sleep",
+                                     "mock_utmi";
+
+                       resets = <&gcc GCC_USB0_BCR>;
+
+                       qcom,select-utmi-as-pipe-clk;
+                       #address-cells = <1>;
+                       #size-cells = <1>;
+                       ranges;
+
+                       status = "disabled";
+
+                       usb2_0_dwc: usb@8a00000 {
Could you please remove the `2_0' part of the label?
Sure.

Regards,
Nitheesh



[Index of Archives]     [Linux ARM Kernel]     [Linux ARM]     [Linux Omap]     [Fedora ARM]     [Linux for Sparc]     [IETF Annouce]     [Security]     [Bugtraq]     [Linux MIPS]     [ECOS]     [Asterisk Internet PBX]     [Linux API]

  Powered by Linux