On Tue, May 16, 2023 at 03:22:41AM +0200, Konrad Dybcio wrote:
>
>
> On 9.05.2023 05:01, Bjorn Andersson wrote:
> > The CRD has Micro SD slot, introduce the necessary DeviceTree nodes for
> > enabling this.
> >
> > Signed-off-by: Bjorn Andersson <quic_bjorande@xxxxxxxxxxx>
> > ---
> > arch/arm64/boot/dts/qcom/sc8280xp-crd.dts | 80 +++++++++++++++++++++++
> > arch/arm64/boot/dts/qcom/sc8280xp.dtsi | 39 +++++++++++
> > 2 files changed, 119 insertions(+)
> >
> > diff --git a/arch/arm64/boot/dts/qcom/sc8280xp-crd.dts b/arch/arm64/boot/dts/qcom/sc8280xp-crd.dts
> > index 5b25d54b9591..f83411e0e7f8 100644
> > --- a/arch/arm64/boot/dts/qcom/sc8280xp-crd.dts
> > +++ b/arch/arm64/boot/dts/qcom/sc8280xp-crd.dts
> > @@ -308,6 +308,13 @@ vreg_l1c: ldo1 {
> > regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
> > };
> >
> > + vreg_l6c: ldo6 {
> > + regulator-name = "vreg_l6c";
> > + regulator-min-microvolt = <1800000>;
> > + regulator-max-microvolt = <2960000>;
> > + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
> > + };
> > +
> > vreg_l7c: ldo7 {
> > regulator-name = "vreg_l7c";
> > regulator-min-microvolt = <2504000>;
> > @@ -318,6 +325,13 @@ vreg_l7c: ldo7 {
> > RPMH_REGULATOR_MODE_HPM>;
> > };
> >
> > + vreg_l9c: ldo9 {
> > + regulator-name = "vreg_l9c";
> > + regulator-min-microvolt = <2960000>;
> > + regulator-max-microvolt = <2960000>;
> > + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
> Generally I ask people to add the missing regulator-allow-set-load,
> but in case of the RPMh driver, should we also consider allowing LPM?
>
I prefer to avoid LPM and dynamic load management, because I don't think
we're doing a good enough job across the kernel to ensure we get back to
HPM when needed.
At some point this needs to be re-evaluated though.
> > + };
> > +
> > vreg_l13c: ldo13 {
> > regulator-name = "vreg_l13c";
> > regulator-min-microvolt = <3072000>;
> > @@ -600,6 +614,18 @@ &remoteproc_nsp0 {
> > status = "okay";
> > };
> >
> > +&sdc2 {
> > + cd-gpios = <&tlmm 131 GPIO_ACTIVE_LOW>;
> > + pinctrl-names = "default", "sleep";
> > + pinctrl-0 = <&sdc2_default_state>;
> > + pinctrl-1 = <&sdc2_sleep_state>;
> pinctrl-n
> pinctrl-names
>
> please
That's ugly, but I see the symmetry to other -# vs -names
> > + vmmc-supply = <&vreg_l9c>;
> > + vqmmc-supply = <&vreg_l6c>;
> > + no-sdio;
> > + no-mmc;
> > + status = "okay";
> > +};
> > +
> > &uart17 {
> > compatible = "qcom,geni-debug-uart";
> >
> > @@ -842,6 +868,60 @@ wake-n-pins {
> > };
> > };
> >
> > + sdc2_default_state: sdc2-default-state {
> > + clk-pins {
> > + pins = "sdc2_clk";
> > + drive-strength = <16>;
> > + bias-disable;
> > + };
> > +
> > + cmd-pins {
> > + pins = "sdc2_cmd";
> > + drive-strength = <16>;
> > + bias-pull-up;
> > + };
> > +
> > + data-pins {
> > + pins = "sdc2_data";
> > + drive-strength = <16>;
> > + bias-pull-up;
> > + };
> > +
> > + card-detect-pins {
> > + pins = "gpio131";
> > + function = "gpio";
> > + drive-strength = <2>;
> > + bias-disable;
> > + };
> > + };
> > +
> > + sdc2_sleep_state: sdc2-sleep-state {
> > + clk-pins {
> > + pins = "sdc2_clk";
> > + drive-strength = <2>;
> > + bias-disable;
> > + };
> > +
> > + cmd-pins {
> > + pins = "sdc2_cmd";
> > + drive-strength = <2>;
> > + bias-pull-up;
> > + };
> > +
> > + data-pins {
> > + pins = "sdc2_data";
> > + drive-strength = <2>;
> > + bias-pull-up;
> > + };
> > +
> > + card-detect-pins {
> > + pins = "gpio131";
> > + function = "gpio";
> > + drive-strength = <2>;
> > + bias-disable;
> > + };
> > + };
> That's totally SoC-specific, modulo the CD pin which can have
> its own separate node and label
>
The drive-strength and bias properties are board specific. Also, at this
time the CRD is the only board I'm aware of having the SD-card slot.
I suggest that we move it out of here once there's another user...
> > +
> > tpad_default: tpad-default-state {
> > int-n-pins {
> > pins = "gpio182";
> > diff --git a/arch/arm64/boot/dts/qcom/sc8280xp.dtsi b/arch/arm64/boot/dts/qcom/sc8280xp.dtsi
> > index 8fa9fbfe5d00..21dfb48d923c 100644
> > --- a/arch/arm64/boot/dts/qcom/sc8280xp.dtsi
> > +++ b/arch/arm64/boot/dts/qcom/sc8280xp.dtsi
> > @@ -2815,6 +2815,45 @@ data-pins {
> > };
> > };
> >
> > + sdc2: mmc@8804000 {
> > + compatible = "qcom,sc8280xp-sdhci", "qcom,sdhci-msm-v5";
> > + reg = <0 0x08804000 0 0x1000>;
> > +
> > + interrupts = <GIC_SPI 207 IRQ_TYPE_LEVEL_HIGH>,
> > + <GIC_SPI 223 IRQ_TYPE_LEVEL_HIGH>;
> > + interrupt-names = "hc_irq", "pwr_irq";
> > +
> > + clocks = <&gcc GCC_SDCC2_AHB_CLK>,
> > + <&gcc GCC_SDCC2_APPS_CLK>,
> > + <&rpmhcc RPMH_CXO_CLK>;
> > + clock-names = "iface", "core", "xo";
> > + resets = <&gcc GCC_SDCC4_BCR>;
> 4?
>
That's a typo. Thanks.
> > + interconnects = <&aggre2_noc MASTER_SDCC_2 0 &mc_virt SLAVE_EBI1 0>,
> > + <&gem_noc MASTER_APPSS_PROC 0 &config_noc SLAVE_SDCC_2 0>;
> > + interconnect-names = "sdhc-ddr","cpu-sdhc";
> > + iommus = <&apps_smmu 0x4e0 0x0>;
> > + power-domains = <&rpmhpd SC8280XP_CX>;
> > + operating-points-v2 = <&sdc2_opp_table>;
> > + bus-width = <4>;
> > + dma-coherent;
> > +
> > + status = "disabled";
> > +
> > + sdc2_opp_table: opp-table {
> > + compatible = "operating-points-v2";
> > +
> > + opp-100000000 {
> > + opp-hz = /bits/ 64 <100000000>;
> > + required-opps = <&rpmhpd_opp_low_svs>;
> You specified interconnects, but no bw values.. was that on purpose?
>
Assumed the driver did something clever, when I didn't see anything for
the other boards I looked at either. Will reconsider.
> Other than these nits, lgtm
> (generally, my dt sources don't even have sdhci to compare)
>
Thanks,
Bjorn
> Konrad
> > + };
> > +
> > + opp-202000000 {
> > + opp-hz = /bits/ 64 <202000000>;
> > + required-opps = <&rpmhpd_opp_svs_l1>;
> > + };
> > + };
> > + };
> > +
> > usb_0_qmpphy: phy@88eb000 {
> > compatible = "qcom,sc8280xp-qmp-usb43dp-phy";
> > reg = <0 0x088eb000 0 0x4000>;
