This is a continue of [1]. It was decided to take a more gradual approach to implement LEDs support for switch and phy starting with basic support and then implementing the hw control part when we have all the prereq done. This series implements only the brightness_set() and blink_set() ops. An example of switch implementation is done with qca8k. For PHY a more generic approach is used with implementing the LED support in PHY core and with the user (in this case marvell) adding all the required functions. Currently we set the default-state as "keep" to not change the default configuration of the declared LEDs since almost every switch have a default configuration. [1] https://lore.kernel.org/lkml/20230216013230.22978-1-ansuelsmth@xxxxxxxxx/ Changes in new series v3: - Move QCA8K_LEDS Kconfig option from tristate to bool - Use new helper led_init_default_state_get for default-state in qca8k - Drop cled_qca8k_brightness_get() as there isn't a good way to describe the mode the led is currently in - Rework qca8k_led_brightness_get() to return true only when LED is set to always ON Changes in new series v2: - Add LEDs node for rb3011 - Fix rb3011 switch node unevaluated properties while running make dtbs_check - Fix a copypaste error in qca8k-leds.c for port 4 required shift - Drop phy-handle usage for qca8k and use qca8k_port_to_phy() - Add review tag from Andrew - Add Christian Marangi SOB in each Andrew patch - Add extra description for dsa-port stressing that PHY have no access and LED are controlled by the related MAC - Add missing additionalProperties for dsa-port.yaml and ethernet-phy.yaml Changes from the old v8 series: - Drop linux,default-trigger set to netdev. - Dropped every hw control related patch and implement only blink_set and brightness_set - Add default-state to "keep" for each LED node example Andrew Lunn (6): net: phy: Add a binding for PHY LEDs net: phy: phy_device: Call into the PHY driver to set LED brightness. net: phy: marvell: Add software control of the LEDs net: phy: phy_device: Call into the PHY driver to set LED blinking. net: phy: marvell: Implement led_blink_set() arm: mvebu: dt: Add PHY LED support for 370-rd WAN port Christian Marangi (8): net: dsa: qca8k: move qca8k_port_to_phy() to header net: dsa: qca8k: add LEDs basic support net: dsa: qca8k: add LEDs blink_set() support dt-bindings: net: dsa: dsa-port: Document support for LEDs node dt-bindings: net: dsa: qca8k: add LEDs definition example arm: qcom: dt: Drop unevaluated properties in switch nodes for rb3011 arm: qcom: dt: Add Switch LED for each port for rb3011 dt-bindings: net: phy: Document support for LEDs node .../devicetree/bindings/net/dsa/dsa-port.yaml | 21 ++ .../devicetree/bindings/net/dsa/qca8k.yaml | 24 ++ .../devicetree/bindings/net/ethernet-phy.yaml | 31 +++ arch/arm/boot/dts/armada-370-rd.dts | 14 ++ arch/arm/boot/dts/qcom-ipq8064-rb3011.dts | 124 +++++++++- drivers/net/dsa/qca/Kconfig | 7 + drivers/net/dsa/qca/Makefile | 1 + drivers/net/dsa/qca/qca8k-8xxx.c | 19 +- drivers/net/dsa/qca/qca8k-leds.c | 229 ++++++++++++++++++ drivers/net/dsa/qca/qca8k.h | 83 +++++++ drivers/net/phy/marvell.c | 81 ++++++- drivers/net/phy/phy_device.c | 115 +++++++++ include/linux/phy.h | 33 +++ 13 files changed, 758 insertions(+), 24 deletions(-) create mode 100644 drivers/net/dsa/qca/qca8k-leds.c -- 2.39.2
