Hi! v3 -> v4 changelog: - Drop "Always set QoS params on QNoC", it only causes issues.. this can be investigated another day, as it's not necessary for operation - Drop "Add a way to always set QoS registers", same as /\ - Add a way (and use it) to have no bus_clocks (the ones we set rate on), as at least msm8996 has a bus (A0NoC) that doesn't have any and does all the scaling through RPM requests - Promote 8996 icc to core_initcall - Introduce keep_alive (see patch [11/12]) (important!, will be used by at least 6375) - Allow negative QoS offsets in preparation for introducing 8998 icc [12/12] Link to v3: https://lore.kernel.org/linux-arm-msm/20230116132152.405535-1-konrad.dybcio@xxxxxxxxxx/ v2 -> v3 changelog: - Drop "Don't set QoS params before non-zero bw is requested" - Rebase on next - [1/9] ("..make QoS INVALID default.."): remove unused define for MODE_INVALID_VAL - Pick up tags v1 -> v2 changelog: - reorder "make QoS INVALID default", makes more sense to have it before "Always set QoS params on QNoC" - Limit ap_owned-independent QoS setting to QNoC only - Add new patches for handling the 8996-and-friends clocks situation and optional BIMC regardless-of-ap_owned QoS programming [1] https://lore.kernel.org/linux-arm-msm/14e06574-f95e-8960-0243-8c95a1c294e9@xxxxxxxxxx/T/#m056692bea71d4c272968d5e07afbd9eb07a88123 [2] https://lore.kernel.org/linux-arm-msm/20230110132202.956619-1-konrad.dybcio@xxxxxxxxxx/ This series grew quite a bit bigger than the previous [1] attempt, so I decided to also add a cover letter. Link to v2: [2] It addresses a few things that were not quite right: - Setting QoS params before a "real" (non-zero) bandwidth request makes little sense (since there's no data supposed to flow through the bus, why would the QoS matter) and (at least newer) downstream prevents that from happening. Do the same in Patch 1. - QNoC type buses expect to always have their QoS registers set as long as there's a non-INVALID QoS mode set; ap_owned is not really a thing on these anymore, Patch 3 handles that. - The recent MSM8996 boot fix was done quickly and not quite properly, leading to possibly setting the aggregate bus rate on "normal" hardware interface clocks; this series handles that by limiting the number of bus_clocks to 2 (which is the maximum that makes sense, anyway) and handling the rest as "intf_clocks", which are required to access the hardware at the other end. Patches 5-8 take care of that and Patch 10 reverts the _optional moniker in clk_get_ to make sure we always have the bus scaling clocks, as they're well, kind of important ;) - Similarly to QNoC, BIMC on "newer" (which can be loosely approximated by "new enough" == "has only BIMC and QNoC hosts") SoCs expects to always receive QoS programming, whereas BIMC on "older" SoCs cries like a wild boar and crashes the platform when trying to do so unconditionally. Patch 9 adds a way to take care of that for newer SoCs (like SM6375) - QoS mode INVALID was assumed by developers before to be the default ("I didn't specify any QoS settings, so the driver can't assume I did.. right? right!?" - wrong, partial struct initialization led to 0 being set and 0 corresponded to QoS mode FIXED). Make it so, as that's the logical choice. This allows the "Always set QoS params on QNoC" patch to work without setting tons of what-should- -obviously-be-the-default values everywhere, as well as fixes older drivers that set ap_owned = true but left the QoS mode field unset. Patch 2 cleans that up. - Some nodes are physically connected over more than one channel (usually DDR or other high-throughput paths). Patch 4 allows that to be reflected in calculations. This will be required for at least MSM8998 and SM6375 (which will be submitted soon after this lands) Konrad Dybcio (12): interconnect: qcom: rpm: make QoS INVALID default, separate out driver data interconnect: qcom: rpm: Add support for specifying channel num interconnect: qcom: Sort kerneldoc entries interconnect: qcom: rpm: Rename icc desc clocks to bus_blocks interconnect: qcom: rpm: Rename icc provider num_clocks to num_bus_clocks interconnect: qcom: rpm: Handle interface clocks interconnect: qcom: icc-rpm: Allow negative num_bus_clocks interconnect: qcom: msm8996: Specify no bus clock scaling on A0NoC interconnect: qcom: rpm: Don't use clk_get_optional for bus clocks anymore interconnect: qcom: msm8996: Promote to core_initcall interconnect: qcom: icc-rpm: Introduce keep_alive interconnect: qcom: icc-rpm: Allow negative QoS offset drivers/interconnect/qcom/icc-rpm.c | 101 ++++++++++++++++++++-------- drivers/interconnect/qcom/icc-rpm.h | 41 +++++++---- drivers/interconnect/qcom/msm8996.c | 35 ++++++---- drivers/interconnect/qcom/sdm660.c | 16 ++--- 4 files changed, 126 insertions(+), 67 deletions(-) -- 2.39.1
