These patches provide cpufreq scaling on devices with Krait CPUs. In Krait CPU designs there's one PLL and two muxes per CPU, allowing us to switch CPU frequencies independently. secondary +-----+ + | QSB |-------+------------|\ +-----+ | | |-+ | +-------|/ | | | + | +-----+ | | | | PLL |----+-------+ | primary +-----+ | | | + | | +-----|\ +------+ +-------+ | | | \ | | | HFPLL |----------+-----------------| |-----| CPU0 | +-------+ | | | | | | | | | | +-----+ | / +------+ | | +-| / 2 |---------|/ | | +-----+ + | | secondary | | + | +------------|\ | | |-+ +---------------|/ | primary + | + +-----|\ +------+ +-------+ | \ | | | HFPLL |----------------------------| |-----| CPU1 | +-------+ | | | | | | +-----+ | / +------+ +-| / 2 |---------|/ +-----+ + To support this in the common clock framework we model the muxes, dividers, and PLLs as different clocks. CPUfreq only interacts with the primary mux (farthest right in the diagram). When CPUfreq sets a rate, the mux code finds the best parent that can provide the rate. Due to the design, QSB and the top PLL are always a fixed rate and thus only support one frequency each. These sources provide the lowest frequencies for the CPUs. The HFPLLs are where we can make the CPU go faster (GHz range). Sometimes we need to run the HFPLL twice as fast and divide it by two to get a particular frequency. When switching rates we can't leave the CPU clocked by the HFPLL because we need to turn off the output of the PLL when changing its frequency. This means we have to switch over to the secondary mux and use one of the fixed sources. This is why we need something like the safe parent patch. I plan to submit the DTS changes through arm-soc, but I've included everything here to make it easier to pick things up for testing, etc. If anything can be picked up right now it would be better to reduce the churn over time as other pieces settle. Some things are not done, but I'm posting this now to get it out there and because the clock framework patches needed some rework due to recent changes. Changes since v2: * Switched to cpufreq-dt * Ported over PVS binding * Stripped out cpu logical map to make modules work * Dropped patches that merged upstream Changes since v1: * Added IPQ and APQ8064 support * Switched to cpufreq-generic * Added OPP parsing from DT (need to write binding though) * New patches to make clk-generic.c go away * Made mux and divider reusable for non-MMIO devices * Added a mux_determine_rate_closest (not sure if this is really needed) * Added unregistration of muxes * New patch to avoid sending high frequencies down to devices using clocks TODO: * Add Krait regulator voltage scaling (not strictly necessary) * Add some thermal awareness * Use efuse/eeprom API instead of hardcoding the location in the driver * Figure out how to express number of CPUs without relying on linux's concept of number of CPUs and logical CPU mapping * Trim down the probe code for krait-cc so that we just register clocks and don't enable or set rates Stephen Boyd (13): ARM: Add Krait L2 register accessor functions clk: mux: Split out register accessors for reuse clk: Avoid sending high rates to downstream clocks during set_rate clk: Add safe switch hook clk: qcom: Add support for High-Frequency PLLs (HFPLLs) clk: qcom: Add HFPLL driver clk: qcom: Add MSM8960/APQ8064's HFPLLs clk: qcom: Add IPQ806X's HFPLLs clk: qcom: Add support for Krait clocks clk: qcom: Add KPSS ACC/GCC driver clk: qcom: Add Krait clock controller driver cpufreq: Add module to register cpufreq on Krait CPUs ARM: dts: qcom: Add necessary DT data for Krait cpufreq .../devicetree/bindings/arm/msm/qcom,kpss-acc.txt | 7 + .../devicetree/bindings/arm/msm/qcom,kpss-gcc.txt | 28 ++ .../devicetree/bindings/arm/msm/qcom,pvs.txt | 38 +++ .../devicetree/bindings/clock/qcom,hfpll.txt | 40 +++ .../devicetree/bindings/clock/qcom,krait-cc.txt | 22 ++ arch/arm/boot/dts/qcom-apq8064.dtsi | 230 ++++++++++++++ arch/arm/boot/dts/qcom-msm8960.dtsi | 49 +++ arch/arm/boot/dts/qcom-msm8974.dtsi | 311 +++++++++++++++++- arch/arm/common/Kconfig | 3 + arch/arm/common/Makefile | 1 + arch/arm/common/krait-l2-accessors.c | 58 ++++ arch/arm/include/asm/krait-l2-accessors.h | 20 ++ drivers/clk/clk-mux.c | 76 +++-- drivers/clk/clk.c | 95 ++++-- drivers/clk/qcom/Kconfig | 28 ++ drivers/clk/qcom/Makefile | 5 + drivers/clk/qcom/clk-hfpll.c | 253 +++++++++++++++ drivers/clk/qcom/clk-hfpll.h | 54 ++++ drivers/clk/qcom/clk-krait.c | 166 ++++++++++ drivers/clk/qcom/clk-krait.h | 49 +++ drivers/clk/qcom/gcc-ipq806x.c | 83 +++++ drivers/clk/qcom/gcc-msm8960.c | 172 ++++++++++ drivers/clk/qcom/hfpll.c | 109 +++++++ drivers/clk/qcom/kpss-xcc.c | 95 ++++++ drivers/clk/qcom/krait-cc.c | 352 +++++++++++++++++++++ drivers/cpufreq/Kconfig.arm | 9 + drivers/cpufreq/Makefile | 1 + drivers/cpufreq/qcom-cpufreq.c | 204 ++++++++++++ include/dt-bindings/clock/qcom,gcc-msm8960.h | 2 + include/linux/clk-provider.h | 10 +- 30 files changed, 2515 insertions(+), 55 deletions(-) create mode 100644 Documentation/devicetree/bindings/arm/msm/qcom,kpss-gcc.txt create mode 100644 Documentation/devicetree/bindings/arm/msm/qcom,pvs.txt create mode 100644 Documentation/devicetree/bindings/clock/qcom,hfpll.txt create mode 100644 Documentation/devicetree/bindings/clock/qcom,krait-cc.txt create mode 100644 arch/arm/common/krait-l2-accessors.c create mode 100644 arch/arm/include/asm/krait-l2-accessors.h create mode 100644 drivers/clk/qcom/clk-hfpll.c create mode 100644 drivers/clk/qcom/clk-hfpll.h create mode 100644 drivers/clk/qcom/clk-krait.c create mode 100644 drivers/clk/qcom/clk-krait.h create mode 100644 drivers/clk/qcom/hfpll.c create mode 100644 drivers/clk/qcom/kpss-xcc.c create mode 100644 drivers/clk/qcom/krait-cc.c create mode 100644 drivers/cpufreq/qcom-cpufreq.c -- The Qualcomm Innovation Center, Inc. is a member of the Code Aurora Forum, a Linux Foundation Collaborative Project -- To unsubscribe from this list: send the line "unsubscribe linux-arm-msm" in the body of a message to majordomo@xxxxxxxxxxxxxxx More majordomo info at http://vger.kernel.org/majordomo-info.html
