Re: [PATCH v1 12/14] drm/msm/disp/dpu1: revise timing engine programming to work for DSC

[Date Prev][Date Next][Thread Prev][Thread Next][Date Index][Thread Index]

 



On 24/01/2023 19:55, Kuogee Hsieh wrote:

On 1/24/2023 1:11 AM, Dmitry Baryshkov wrote:
On 23/01/2023 20:24, Kuogee Hsieh wrote:
Current implementation timing engine programming does not consider
compression factors. This patch add consideration of DSC factors
while programming timing engine.

Signed-off-by: Kuogee Hsieh <quic_khsieh@xxxxxxxxxxx>
---
  .../gpu/drm/msm/disp/dpu1/dpu_encoder_phys_vid.c   |   2 +
  drivers/gpu/drm/msm/disp/dpu1/dpu_hw_catalog.h     |  14 ++-
  drivers/gpu/drm/msm/disp/dpu1/dpu_hw_intf.c        | 132 +++++++++++++--------
  drivers/gpu/drm/msm/disp/dpu1/dpu_hw_intf.h        |  10 +-
  drivers/gpu/drm/msm/disp/dpu1/dpu_hw_top.h         |   6 +-
  5 files changed, 110 insertions(+), 54 deletions(-)


[skipped]

@@ -113,82 +124,96 @@ static void dpu_hw_intf_setup_timing_engine(struct dpu_hw_intf *ctx,
      /* read interface_cfg */
      intf_cfg = DPU_REG_READ(c, INTF_CONFIG);
  -    if (ctx->cap->type == INTF_DP)
+    if (ctx->cap->type == INTF_EDP || ctx->cap->type == INTF_DP)
          dp_intf = true;
        hsync_period = p->hsync_pulse_width + p->h_back_porch + p->width +
-    p->h_front_porch;
+            p->h_front_porch;
      vsync_period = p->vsync_pulse_width + p->v_back_porch + p->height +
-    p->v_front_porch;
+            p->v_front_porch;

Actually I went on through the history and found the previous submission, https://patchwork.freedesktop.org/patch/471505/. Exactly the same piece of code. Did you expect that the comments will be different this time?

I really hoped that at that time we already went through this. But it seems I was wrong. That series went through v10 or v12 before being accepted. And it was just adding wide_bus_en. Back at that time we lightly discussed that the code will receive compression support. But I never expected to see the original submission again.

It might sound bad, but could you please find somebody who can do internal review for you? Good internal review.

That said, I really do not expect to see v2 before the whole series is reworked, restructured and prepared for the review on your side.

This timing engine code is derived from our downstream code directly and it has been used at many mobile devices by many vendors for many years already.

On the other words, it had been tested very thorough and works on dsi/dp/hdmi/dsc/widebus applications.

As far as I understand, it has been tested on the recent generations of the hardware. I doubt that anybody retests new techpack drops on previous hardware generations. Correct?

When was the last time this particular code drop was tested on INTF_HDMI? I think it was back in the 4.4 era. Newer vendor kernels do not have hdmi-staging, so at least the claim of testing this codepiece on HDMI is not correct.

What is the earliest chip that has been driven by this particular code instance?

When i brought dsc v1.2 over, I just merged it over and did not consider too much.

Can we adapt this code so that both upstream and down stream shared same timing engine programming so that easier to maintain?

We have been discussing exactly the same piece of code a year ago. Could you please recheck the comments that were provided to your patches. And I actually mean that. There were 12 iterations of wide bus patchset. Timing engine programming patch had 8. I do not want to start again from the very beginning.

The basic idea is that you have to evolve the code rather than flushing us with the 'latest and greatest code dump'. Split this into individual atomic changes that we can review. Provide justification (= motivation) for each change. Previously we haven't seen them.

We know that current function works. We must be able to assume that new instance doesn't break things. Or, if something breaks, understand which particular change broke it. Consider the case that your patch breaks msm8998. Or sdm845. How can we cope? Would you be able to spot the place which did that? I know I wouldn't. The only way would be to revert the patch completely. And inherently the whole series.


        display_v_start = ((p->vsync_pulse_width + p->v_back_porch) *
-    hsync_period) + p->hsync_skew;
+            hsync_period) + p->hsync_skew;
      display_v_end = ((vsync_period - p->v_front_porch) * hsync_period) +
-    p->hsync_skew - 1;
+            p->hsync_skew - 1;
+
+    hsync_ctl = (hsync_period << 16) | p->hsync_pulse_width;
        hsync_start_x = p->h_back_porch + p->hsync_pulse_width;
      hsync_end_x = hsync_period - p->h_front_porch - 1;
  -    if (p->width != p->xres) { /* border fill added */
-        active_h_start = hsync_start_x;
-        active_h_end = active_h_start + p->xres - 1;
-    } else {
-        active_h_start = 0;
-        active_h_end = 0;
-    }
-
-    if (p->height != p->yres) { /* border fill added */
-        active_v_start = display_v_start;
-        active_v_end = active_v_start + (p->yres * hsync_period) - 1;
-    } else {
-        active_v_start = 0;
-        active_v_end = 0;
-    }
-
-    if (active_h_end) {
-        active_hctl = (active_h_end << 16) | active_h_start;
-        intf_cfg |= INTF_CFG_ACTIVE_H_EN;
-    } else {
-        active_hctl = 0;
-    }
-
-    if (active_v_end)
-        intf_cfg |= INTF_CFG_ACTIVE_V_EN;
-
-    hsync_ctl = (hsync_period << 16) | p->hsync_pulse_width;
-    display_hctl = (hsync_end_x << 16) | hsync_start_x;
-
      /*
       * DATA_HCTL_EN controls data timing which can be different from
       * video timing. It is recommended to enable it for all cases, except
       * if compression is enabled in 1 pixel per clock mode
       */
+    if (!p->compression_en || p->wide_bus_en)
+        intf_cfg2 |= INTF_CFG2_DATA_HCTL_EN;
+
      if (p->wide_bus_en)
-        intf_cfg2 |= INTF_CFG2_DATABUS_WIDEN | INTF_CFG2_DATA_HCTL_EN;
+        intf_cfg2 |= INTF_CFG2_DATABUS_WIDEN;
  +    /*
+     * If widebus is disabled:
+     * For uncompressed stream, the data is valid for the entire active
+     * window period.
+     * For compressed stream, data is valid for a shorter time period
+     * inside the active window depending on the compression ratio.
+     *
+     * If widebus is enabled:
+     * For uncompressed stream, data is valid for only half the active
+     * window, since the data rate is doubled in this mode.
+     * p->width holds the adjusted width for DP but unadjusted width for DSI +     * For compressed stream, data validity window needs to be adjusted for
+     * compression ratio and then further halved.
+     */
      data_width = p->width;
  +    if (p->compression_en) {
+        if (p->wide_bus_en)
+            data_width = DIV_ROUND_UP(p->dce_bytes_per_line, 6);
+        else
+            data_width = DIV_ROUND_UP(p->dce_bytes_per_line, 3);
+    } else if (!dp_intf && p->wide_bus_en) {
+        data_width = p->width >> 1;
+    } else {
+        data_width = p->width;
+    }
+
      hsync_data_start_x = hsync_start_x;
      hsync_data_end_x =  hsync_start_x + data_width - 1;
  +    display_hctl = (hsync_end_x << 16) | hsync_start_x;
      display_data_hctl = (hsync_data_end_x << 16) | hsync_data_start_x;
        if (dp_intf) {
          /* DP timing adjustment */
          display_v_start += p->hsync_pulse_width + p->h_back_porch;
          display_v_end   -= p->h_front_porch;
+    }
+
+    intf_cfg |= INTF_CFG_ACTIVE_H_EN;
+    intf_cfg |= INTF_CFG_ACTIVE_V_EN;
+    active_h_start = hsync_start_x;
+    active_h_end = active_h_start + p->xres - 1;
+    active_v_start = display_v_start;
+    active_v_end = active_v_start + (p->yres * hsync_period) - 1;
  -        active_h_start = hsync_start_x;
-        active_h_end = active_h_start + p->xres - 1;
-        active_v_start = display_v_start;
-        active_v_end = active_v_start + (p->yres * hsync_period) - 1;
+    active_hctl = (active_h_end << 16) | active_h_start;
  -        active_hctl = (active_h_end << 16) | active_h_start;
+    if (dp_intf) {
          display_hctl = active_hctl;
  -        intf_cfg |= INTF_CFG_ACTIVE_H_EN | INTF_CFG_ACTIVE_V_EN;
+        if (p->compression_en) {
+            active_data_hctl = (hsync_start_x + p->extra_dto_cycles) << 16;
+            active_data_hctl += hsync_start_x;
+
+            display_data_hctl = active_data_hctl;
+        }
      }
  +    _check_and_set_comp_bit(ctx, p->dsc_4hs_merge, p->compression_en, &intf_cfg2);
+
      den_polarity = 0;
      if (ctx->cap->type == INTF_HDMI) {
          hsync_polarity = p->yres >= 720 ? 0 : 1;
@@ -202,7 +227,7 @@ static void dpu_hw_intf_setup_timing_engine(struct dpu_hw_intf *ctx,


--
With best wishes
Dmitry




[Index of Archives]     [Linux ARM Kernel]     [Linux ARM]     [Linux Omap]     [Fedora ARM]     [Linux for Sparc]     [IETF Annouce]     [Security]     [Bugtraq]     [Linux MIPS]     [ECOS]     [Asterisk Internet PBX]     [Linux API]

  Powered by Linux