Re: [RFC v4 0/5] Add multiport support for DWC3 controllers

[Date Prev][Date Next][Thread Prev][Thread Next][Date Index][Thread Index]

 





On 1/19/2023 9:13 AM, Bjorn Andersson wrote:
On Sun, Jan 15, 2023 at 05:11:41PM +0530, Krishna Kurapati wrote:
Currently the DWC3 driver supports only single port controller which
requires at most two PHYs ie HS and SS PHYs. There are SoCs that has
DWC3 controller with multiple ports that can operate in host mode.
Some of the port supports both SS+HS and other port supports only HS
mode.

This change primarily refactors the Phy logic in core driver to allow
multiport support with Generic Phy's.

Chananges have been tested on  QCOM SoC SA8295P which has 4 ports (2
are HS+SS capable and 2 are HS only capable).


I can confirm that applying this series allow me to use all 6 USB ports
on the ADP. Looking forward to v5.

Thanks,
Bjorn

Thanks Bjorn for testing it out.

Regards,
Krishna,
Changes in v4:
Added DT support for SA8295p.

Changes in v3:
Incase any PHY init fails, then clear/exit the PHYs that
are already initialized.

Changes in v2:
Changed dwc3_count_phys to return the number of PHY Phandles in the node.
This will be used now in dwc3_extract_num_phys to increment num_usb2_phy
and num_usb3_phy.

Added new parameter "ss_idx" in dwc3_core_get_phy_ny_node and changed its
structure such that the first half is for HS-PHY and second half is for
SS-PHY.

In dwc3_core_get_phy, for multiport controller, only if SS-PHY phandle is
present, pass proper SS_IDX else pass -1.

Link to v3: https://lore.kernel.org/all/1654709787-23686-1-git-send-email-quic_harshq@xxxxxxxxxxx/#r
Link to v2: https://lore.kernel.org/all/1653560029-6937-1-git-send-email-quic_harshq@xxxxxxxxxxx/#r

Krishna Kurapati (5):
   dt-bindings: usb: Add bindings to support multiport properties
   usb: dwc3: core: Refactor PHY logic to support Multiport Controller
   usb: dwc3: core: Do not setup event buffers for host only controllers
   usb: dwc3: qcom: Add multiport controller support for qcom wrapper
   arm: dts: msm: Add multiport controller node for usb

  .../devicetree/bindings/usb/snps,dwc3.yaml    |  42 ++-
  arch/arm64/boot/dts/qcom/sa8295p-adp.dts      |  49 +++
  arch/arm64/boot/dts/qcom/sc8280xp.dtsi        |  60 ++++
  drivers/usb/dwc3/core.c                       | 325 +++++++++++++-----
  drivers/usb/dwc3/core.h                       |  15 +-
  drivers/usb/dwc3/drd.c                        |  14 +-
  drivers/usb/dwc3/dwc3-qcom.c                  |  28 +-
  7 files changed, 429 insertions(+), 104 deletions(-)

--
2.39.0




[Index of Archives]     [Linux ARM Kernel]     [Linux ARM]     [Linux Omap]     [Fedora ARM]     [Linux for Sparc]     [IETF Annouce]     [Security]     [Bugtraq]     [Linux MIPS]     [ECOS]     [Asterisk Internet PBX]     [Linux API]

  Powered by Linux