Re: [PATCH v3 12/15] arm64: dts: qcom: msm8916: specify per-sensor calibration cells

[Date Prev][Date Next][Thread Prev][Thread Next][Date Index][Thread Index]

 




On 20.12.2022 03:47, Dmitry Baryshkov wrote:
> Specify pre-parsed per-sensor calibration nvmem cells in the tsens
> device node rather than parsing the whole data blob in the driver.
> 
> Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@xxxxxxxxxx>
> ---
>  arch/arm64/boot/dts/qcom/msm8916.dtsi | 70 ++++++++++++++++++++++++---
>  1 file changed, 64 insertions(+), 6 deletions(-)
> 
> diff --git a/arch/arm64/boot/dts/qcom/msm8916.dtsi b/arch/arm64/boot/dts/qcom/msm8916.dtsi
> index 2ca8e977fc2a..af7ba66bb7cd 100644
> --- a/arch/arm64/boot/dts/qcom/msm8916.dtsi
> +++ b/arch/arm64/boot/dts/qcom/msm8916.dtsi
> @@ -442,11 +442,57 @@ qfprom: qfprom@5c000 {
>  			reg = <0x0005c000 0x1000>;
>  			#address-cells = <1>;
>  			#size-cells = <1>;
> -			tsens_caldata: caldata@d0 {
> -				reg = <0xd0 0x8>;
> +			tsens_base1: base1@d0 {
> +				reg = <0xd0 0x1>;
> +				bits = <0 7>;
>  			};
> -			tsens_calsel: calsel@ec {
> -				reg = <0xec 0x4>;
> +			tsens_s0_p1: s0_p1@d0 {
No underscores in node names.

> +				reg = <0xd0 0x2>;
> +				bits = <7 5>;
> +			};
> +			tsens_s0_p2: s0_p2@d1 {
> +				reg = <0xd1 0x2>;
> +				bits = <4 5>;
> +			};
> +			tsens_s1_p1: s1_p1@d2 {
> +				reg = <0xd2 0x1>;
> +				bits = <1 5>;
> +			};
> +			tsens_s1_p2: s1_p2@d2 {
> +				reg = <0xd2 0x2>;
> +				bits = <6 5>;
> +			};
> +			tsens_s2_p1: s2_p1@d3 {
> +				reg = <0xd3 0x1>;
> +				bits = <3 5>;
> +			};
> +			tsens_s2_p2: s2_p2@d4 {
> +				reg = <0xd4 0x1>;
> +				bits = <0 5>;
> +			};
> +			tsens_s3_p1: s3_p1@d4 {
> +				reg = <0xd4 0x2>;
> +				bits = <5 5>;
> +			};
> +			tsens_s3_p2: s3_p2@d5 {
> +				reg = <0xd5 0x1>;
> +				bits = <2 5>;
> +			};
> +			tsens_s4_p1: s4_p1@d5 {
> +				reg = <0xd5 0x2>;
> +				bits = <7 5>;
> +			};
> +			tsens_s4_p2: s4_p2@d6 {
> +				reg = <0xd6 0x2>;
> +				bits = <4 5>;
> +			};
> +			tsens_base2: base2@d7 {
> +				reg = <0xd7 0x1>;
> +				bits = <1 7>;
> +			};
> +			tsens_mode: mode@ec {
> +				reg = <0xef 0x1>;
> +				bits = <5 3>;
>  			};
I (gotta admin, a bit painfully) went through all of these again
and they all seem correct!

Konrad
>  		};
>  
> @@ -473,8 +519,20 @@ tsens: thermal-sensor@4a9000 {
>  			compatible = "qcom,msm8916-tsens", "qcom,tsens-v0_1";
>  			reg = <0x004a9000 0x1000>, /* TM */
>  			      <0x004a8000 0x1000>; /* SROT */
> -			nvmem-cells = <&tsens_caldata>, <&tsens_calsel>;
> -			nvmem-cell-names = "calib", "calib_sel";
> +			nvmem-cells = <&tsens_mode>,
> +				      <&tsens_base1>, <&tsens_base2>,
> +				      <&tsens_s0_p1>, <&tsens_s0_p2>,
> +				      <&tsens_s1_p1>, <&tsens_s1_p2>,
> +				      <&tsens_s2_p1>, <&tsens_s2_p2>,
> +				      <&tsens_s3_p1>, <&tsens_s3_p2>,
> +				      <&tsens_s4_p1>, <&tsens_s4_p2>;
> +			nvmem-cell-names = "mode",
> +					   "base1", "base2",
> +					   "s0_p1", "s0_p2",
> +					   "s1_p1", "s1_p2",
> +					   "s2_p1", "s2_p2",
> +					   "s3_p1", "s3_p2",
> +					   "s4_p1", "s4_p2";
>  			#qcom,sensors = <5>;
>  			interrupts = <GIC_SPI 184 IRQ_TYPE_LEVEL_HIGH>;
>  			interrupt-names = "uplow";



[Index of Archives]     [Linux ARM Kernel]     [Linux ARM]     [Linux Omap]     [Fedora ARM]     [Linux for Sparc]     [IETF Annouce]     [Security]     [Bugtraq]     [Linux MIPS]     [ECOS]     [Asterisk Internet PBX]     [Linux API]

  Powered by Linux