On 22-11-16 13:28:53, Konrad Dybcio wrote:
>
>
> On 16/11/2022 13:17, Abel Vesa wrote:
> > On SM8550, depending on the Qunipro, we can run with G5 or G4.
> > For now, when the major version is 5 or above, we go with G5.
> > Therefore, we need to specifically tell UFS HC that.
> >
> > Signed-off-by: Abel Vesa <abel.vesa@xxxxxxxxxx>
> > ---
> > drivers/ufs/host/ufs-qcom.c | 4 ++++
> > drivers/ufs/host/ufs-qcom.h | 2 ++
> > 2 files changed, 6 insertions(+)
> >
> > diff --git a/drivers/ufs/host/ufs-qcom.c b/drivers/ufs/host/ufs-qcom.c
> > index ca60a5b0292b..72334aefe81c 100644
> > --- a/drivers/ufs/host/ufs-qcom.c
> > +++ b/drivers/ufs/host/ufs-qcom.c
> > @@ -227,6 +227,10 @@ static void ufs_qcom_select_unipro_mode(struct ufs_qcom_host *host)
> > ufshcd_rmwl(host->hba, QUNIPRO_SEL,
> > ufs_qcom_cap_qunipro(host) ? QUNIPRO_SEL : 0,
> > REG_UFS_CFG1);
> > +
> > + if (host->hw_ver.major == 0x05)
> > + ufshcd_rmwl(host->hba, QUNIPRO_G4_SEL, 0, REG_UFS_CFG0);
> > +
> > /* make sure above configuration is applied before we return */
> > mb();
> > }
> > diff --git a/drivers/ufs/host/ufs-qcom.h b/drivers/ufs/host/ufs-qcom.h
> > index 751ded3e3531..10621055bf7f 100644
> > --- a/drivers/ufs/host/ufs-qcom.h
> > +++ b/drivers/ufs/host/ufs-qcom.h
> > @@ -36,6 +36,7 @@ enum {
> > /* On older UFS revisions, this register is called "RETRY_TIMER_REG" */
> > REG_UFS_PARAM0 = 0xD0,
> > REG_UFS_PA_LINK_STARTUP_TIMER = 0xD8,
> > + REG_UFS_CFG0 = 0xD8,
> Are you sure these two should point to the same register? Maybe it deserves
> some kind of a comment?
The REG_UFS_PA_LINK_STARTUP_TIMER is used by non qunipro variants. (UFS
versions below 2.x)
The REG_UFS_CFG0 is used by qunipro variants. (UFS versions above 2.x).
Will add a comment to the later one that would look like this:
"/* Found on UFS versions above 2.x only */"
Thanks,
Abel
>
> Konrad
> > REG_UFS_CFG1 = 0xDC,
> > REG_UFS_CFG2 = 0xE0,
> > REG_UFS_HW_VERSION = 0xE4,
> > @@ -75,6 +76,7 @@ enum {
> > /* bit definitions for REG_UFS_CFG1 register */
> > #define QUNIPRO_SEL BIT(0)
> > +#define QUNIPRO_G4_SEL BIT(5)
> > #define UFS_PHY_SOFT_RESET BIT(1)
> > #define UTP_DBG_RAMS_EN BIT(17)
> > #define TEST_BUS_EN BIT(18)
