On Mon, Oct 31, 2022 at 11:32:15PM +0530, Manivannan Sadhasivam wrote:
> In the preparation of adding support for new gears, let's move the
> logic that finds the gear for each platform to a new function. This helps
> with code readability and also allows the logic to be used in other places
> of the driver in future.
>
> While at it, let's make it clear that this driver only supports symmetric
> gear setting (hs_tx_gear == hs_rx_gear).
>
> Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@xxxxxxxxxx>
Reviewed-by: Andrew Halaney <ahalaney@xxxxxxxxxx>
> ---
> drivers/ufs/host/ufs-qcom.c | 36 +++++++++++++++++++++++-------------
> 1 file changed, 23 insertions(+), 13 deletions(-)
>
> diff --git a/drivers/ufs/host/ufs-qcom.c b/drivers/ufs/host/ufs-qcom.c
> index 38e2ed749d75..c93d2d38b43e 100644
> --- a/drivers/ufs/host/ufs-qcom.c
> +++ b/drivers/ufs/host/ufs-qcom.c
> @@ -278,6 +278,26 @@ static int ufs_qcom_host_reset(struct ufs_hba *hba)
> return 0;
> }
>
> +static u32 ufs_qcom_get_hs_gear(struct ufs_hba *hba, u32 hs_gear)
> +{
> + struct ufs_qcom_host *host = ufshcd_get_variant(hba);
> +
> + if (host->hw_ver.major == 0x1) {
> + /*
> + * HS-G3 operations may not reliably work on legacy QCOM
> + * UFS host controller hardware even though capability
> + * exchange during link startup phase may end up
> + * negotiating maximum supported gear as G3.
> + * Hence downgrade the maximum supported gear to HS-G2.
> + */
> + if (hs_gear > UFS_HS_G2)
> + return UFS_HS_G2;
> + }
> +
> + /* Default is HS-G3 */
> + return UFS_HS_G3;
> +}
> +
> static int ufs_qcom_power_up_sequence(struct ufs_hba *hba)
> {
> struct ufs_qcom_host *host = ufshcd_get_variant(hba);
> @@ -692,19 +712,9 @@ static int ufs_qcom_pwr_change_notify(struct ufs_hba *hba,
> ufshcd_init_pwr_dev_param(&ufs_qcom_cap);
> ufs_qcom_cap.hs_rate = UFS_QCOM_LIMIT_HS_RATE;
>
> - if (host->hw_ver.major == 0x1) {
> - /*
> - * HS-G3 operations may not reliably work on legacy QCOM
> - * UFS host controller hardware even though capability
> - * exchange during link startup phase may end up
> - * negotiating maximum supported gear as G3.
> - * Hence downgrade the maximum supported gear to HS-G2.
> - */
> - if (ufs_qcom_cap.hs_tx_gear > UFS_HS_G2)
> - ufs_qcom_cap.hs_tx_gear = UFS_HS_G2;
> - if (ufs_qcom_cap.hs_rx_gear > UFS_HS_G2)
> - ufs_qcom_cap.hs_rx_gear = UFS_HS_G2;
> - }
> + /* This driver only supports symmetic gear setting i.e., hs_tx_gear == hs_rx_gear */
> + ufs_qcom_cap.hs_tx_gear = ufs_qcom_cap.hs_rx_gear = ufs_qcom_get_hs_gear(hba,
> + ufs_qcom_cap.hs_tx_gear);
>
> ret = ufshcd_get_pwr_dev_param(&ufs_qcom_cap,
> dev_max_params,
> --
> 2.25.1
>
