Re: [PATCH v4 2/2] iio: vadc: Qualcomm SPMI PMIC voltage ADC driver

[Date Prev][Date Next][Thread Prev][Thread Next][Date Index][Thread Index]

 



On 05/11/14 13:57, Ivan T. Ivanov wrote:
> 
> On Wed, 2014-11-05 at 13:09 +0000, Jonathan Cameron wrote:
>> On 03/11/14 15:24, Ivan T. Ivanov wrote:
>>> From: Stanimir Varbanov <svarbanov@xxxxxxxxxx>
>>>
>>> The voltage ADC is peripheral of Qualcomm SPMI PMIC chips. It has
>>> 15 bits resolution and register space inside PMIC accessible across
>>> SPMI bus.
>>>
>>> The vadc driver registers itself through IIO interface.
>>>
>>> Signed-off-by: Stanimir Varbanov <svarbanov@xxxxxxxxxx>
>>> Signed-off-by: Ivan T. Ivanov <iivanov@xxxxxxxxxx>
>> Hi Ivan,
>>
>> Couple of utterly tiny bits inline.  The biggest one is that
>> you store some info about the calibration that you never actually
>> use... Left over from some debugging perhaps?
>>
>> Jonathan
> 
> <snip>
> 
>>> +
>>> +/*
>>> + * VADC_CALIB_ABSOLUTE: uses the 625mV and 1.25V as reference channels.
>>> + * VADC_CALIB_RATIOMETRIC: uses the reference voltage (1.8V) and GND for
>>> + * calibration.
>>> + */
>>> +enum vadc_calibration {
>>> +       VADC_CALIB_ABSOLUTE = 0,
>>> +       VADC_CALIB_RATIOMETRIC
>>> +};
>>> +
>>> +/**
>>> + * struct vadc_linear_graph - Represent ADC characteristics.
>>> + * @dy: numerator slope to calculate the gain.
>> As dy is always equal to vref-gnd you could drop it and use those
>> directly...
>>
>> Conversly you store vref or grnd and never use them...
> 
> I am not sure I am following you. Please take a look in 
> vadc_measure_ref_points() and vadc_calibrate().
Good point on grnd, but vref is set but never read anywhere that I can find..

> 
>>
>>> + * @dx: denominator slope to calculate the gain.
>>> + * @vref: A/D word of the voltage reference used for the channel.
>>> + * @gnd: A/D word of the ground reference used for the channel.
>>> + *
>>> + * Each ADC device has different offset and gain parameters which are
>>> + * computed to calibrate the device.
>>> + */
>>> +struct vadc_linear_graph {
>>> +       s32 dy;
>>> +       s32 dx;
>>> +       s32 vref;
>>> +       s32 gnd;
>>> +};
>>> +
>>>
> 
> Will address blank line comment.
> 
> Regards,
> Ivan
> --
> To unsubscribe from this list: send the line "unsubscribe linux-iio" in
> the body of a message to majordomo@xxxxxxxxxxxxxxx
> More majordomo info at  http://vger.kernel.org/majordomo-info.html
> 
--
To unsubscribe from this list: send the line "unsubscribe linux-arm-msm" in
the body of a message to majordomo@xxxxxxxxxxxxxxx
More majordomo info at  http://vger.kernel.org/majordomo-info.html




[Index of Archives]     [Linux ARM Kernel]     [Linux ARM]     [Linux Omap]     [Fedora ARM]     [Linux for Sparc]     [IETF Annouce]     [Security]     [Bugtraq]     [Linux MIPS]     [ECOS]     [Asterisk Internet PBX]     [Linux API]

  Powered by Linux